• Coupled systems mechanics
• /
• v.1 no.4
• /
• pp.381-395
• /
• 2012

Dynamic response of Pile Supported Structures is highly depended on Soil Pile Structure Interaction. In this paper, by comparison of experimental and numerical dynamic responses of a prototype jacket offshore platform for both hinge based and pile supported boundary conditions, effect of soil-pile-structure interaction on dynamic characteristics of this platform is studied. Jacket and deck of a prototype platform is installed on a hinge-based case first and then platform is installed on eight skirt piles embedded on continuum monolayer sand. Dynamic characteristics of platform in term of natural frequencies, mode shapes and modal damping are compared for both cases. Effects of adding and removing vertical bracing members in top bay of jacket on dynamic characteristics of platform for both boundary conditions are also studied. Numerical simulation of responses for the studied platform is also performed for both mentioned cases using capability of ABAQUS and SACS software. The 3D model using ABAQUS software is created using solid elements for soil and beam elements for jacket, deck and pile members. Mohr-Coulomb failure criterion and pile-soil interface element are used for considering nonlinear pile soil structure interaction. Simplified modeling of soil-pile-structure interaction effect is also studied using SACS software. It is observed that dynamic characteristics of the system changes significantly due to soil-pile-structure interaction. Meanwhile, both of complex and simplified (ABAQUS and SACS, respectively) models can predict this effect accurately for such platforms subjected to dynamic loading in small range of deformation.

• Journal of Hydrogen and New Energy
• /
• v.29 no.1
• /
• pp.41-55
• /
• 2018

General polymer electrolyte fuel cell (PEMFC) operates at less than $80^{\circ}C$. Therefore liquid phase water resulting from electrochemical reaction accumulates and floods the cell which in turn increases the mass transfer loss. To prevent the flooding, it is common to employ serpentine flow channel, which can efficiently export liquid phase water to the outlet. The major drawback of utilizing serpentine flow channel is the large pressure drop that happens between the inlet and outlet. On the other hand, in the high temperature polymer electrolyte fuel cell (HT-PEMFC), since the operating temperature is 130 to $180^{\circ}C$, the generated water is in the state of gas, so the flooding phenomenon is not taken into consideration. In HT-PEMFCs parallel flow channel with lower pressure drop between the inlet and outlet is employed therefore, in order to circulate hydrogen and air in the cell less pumping power is required. In this study we analyzed HT-PEMFC's different flow channels by parallel computation using previously developed 3-D isothermal model. All the flow channels had an active area of $25cm^2$. Also, we numerically compared the performance of HT-PEMFC parallel flow channel with different manifold area and Rib interval against the original serpentine flow channel. Results of the analysis are shown in the form of three-dimensional contour polarization curves, flow characteristics in the channel, current density distribution in the Membrane, overpotential distribution in the catalyst layer, and hydrogen and oxygen concentration distribution. As a result, the performance of a real area fuel cell was predicted.

• Journal of the Society of Naval Architects of Korea
• /
• v.51 no.5
• /
• pp.409-418
• /
• 2014

Simulation of flow past a complex marine structure requires a fine resolution in the vicinity of the structure, whereas a coarse resolution is enough far away from it. Therefore, a lot of grid cells may be wasted, when a simple Cartesian grid system is used for an Immersed Boundary Method (IBM). To alleviate this problems while maintaining the Cartesian frame work, we adopted an Adaptive Mesh Refinement (AMR) scheme where the grid system dynamically and locally refines as needed. In this study, We implemented a moving IBM and an AMR technique in our basic 3D incompressible Navier-Stokes solver. A Volume Of Fluid (VOF) method was used to effectively treat the free surface, and a recently developed Lagrangian Dynamic Subgrid-scale Model (LDSM) was incorporated in the code for accurate turbulence modeling. To capture vortex induced vibration accurately, the equation for the structure movement and the governing equations for fluid flow were solved at the same time implicitly. Also, We have developed an interface by using AutoLISP, which can properly distribute marker particles for IBM, compute the geometrical information of the object, and transfer it to the solver for the main simulation. To verify our numerical methodology, our results were compared with other authors' numerical and experimental results for the benchmark problems, revealing excellent agreement. Using the verified code, we investigated the following cases. (1) simulating flow around a floating sphere. (2) simulating flow past a marine structure.

• Structural Engineering and Mechanics
• /
• v.72 no.2
• /
• pp.169-180
• /
• 2019

The underlying mechanism of the wind-induced vibration of the hangers of the suspension bridges is still not fully understood at present and hence is comprehensively examined in this study. More specifically, a series of field measurements on the No. 2 hanger of the Xihoumen Bridge was first carefully conducted. Large amplitude vibrations of the hanger were found and the oscillation amplitude of the leeward cable was obviously larger than that of the windward cables. Furthermore, the trajectory of the leeward cable was close to an ellipse, which agreed well with the major characteristics of wake-induced vibration. Then, a theoretical model for the wake-induced vibration based on a 3-D continuous cable was established. To obtain the responses of the leeward cable, the finite difference method (FDM) was adopted to numerically solve the established motion equation. Finally, numerical simulations by using the structural parameters of the No. 2 hanger of the Xihoumen Bridge were carried out within the spatial range of $4{\leq}X{\leq}10$ and $0{\leq}Y{\leq}4$ with a uniform interval of ${\Delta}X={\Delta}Y=0.25$. The results obtained from numerical simulations agreed well with the main features obtained from the field observations on the Xihoumen Bridge. This observation indicates that the wake-induced vibration might be one of the reasons for the hanger oscillation of the suspension bridge. In addition, the effects of damping ratio and windward cable movement on the wake-induced vibration of the leeward cable were numerically investigated.

• Nuclear Engineering and Technology
• /
• v.56 no.9
• /
• pp.3864-3871
• /
• 2024

In case of a hypothetical severe accident in a Sodium-cooled Fast Reactor (SFR), coolability of the debris bed in the post-accident phase plays a vital role in mitigating the accident and ensuring the structural integrity of the reactor vessel. Few numerical studies are reported in literature, in which the boiling heat transfer in debris bed is expressed as equivalent heat conduction using similarity law between heat conduction and two-phase heat transfer. However, these studies assumed steady state mass conservation for the boiling zone and neglected the gravity force. Hence, a detailed study has been carried out for various particle sizes and porosities of SFR debris to investigate the influence of above considerations. The effect of gravity on debris bed coolability is studied using steady state model of Lipinski, which showed that gravity has a non-negligible effect, for particle size of 0.3 mm and porosity of 0.5. However, the gravitation force was found to have a negligible effect in dryout heat flux estimation for the bottom cooled configuration. A transient numerical model is developed for simulating the boiling phenomena in debris beds and validated with the published experimental results. The assumption of steady state mass conservation is verified by carrying out transient analysis, which indicated early prediction of the dryout inception. For time dependent heat generation case, the unsteady mass conservation predicted higher DHF compared to constant heat generation.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.11
• /
• pp.119-127
• /
• 2013

Recently, several researches on the development of new economical foundation types have been performed to support floating structures as many offshore structures have been constructed. This study focused on the evaluation of bearing capacity of group suction piles, which are connected by a concrete pile cap. The offshore floating structures are mainly subjected to horizontal loading, so the horizontal bearing capacities of the group suction piles were analyzed by performing 3-dimensional finite element analyses. The group suction piles are expected to behave as a rigid pile due to its shallow embedded depth. Therefore, the detailed soil modeling was necessary to simulate the bearing behavior of soils under low confining pressure. The modulus and the strength of soils were modelled to increase with effective confining pressure in soils. For the parametric study, the center-to-center spacing between piles was varied and two soil types of clay and sands were applied. The analyses results showed that the yielding load of the group pile increased with the increase of the pile spacing and the yielding load of the group piles with 5D spacing was about 3 times larger than that of the single pile with free rotation.

• Journal of Environmental Science International
• /
• v.26 no.5
• /
• pp.621-638
• /
• 2017

Meteorological characteristics related to variations in ozone ($O_3$) concentrations in the Korean peninsula before, during, and after Typhoon Talas (1112) were analyzed using both observation data and numerical modeling. This case study takes into account a high $O_3$ episode (e.g., a daily maximum of ${\geq}90ppb$) without rainfall. Before the typhoon period, high $O_3$ concentrations in the study areas (e.g., Daejeon, Daegu, and Busan) resulted from the combined effects of stable atmospheric conditions with high temperature under a migratory anticyclone (including subsiding air), and wind convergence due to a change in direction caused by the typhoon. The $O_3$ concentrations during the typhoon period decreased around the study area due to very weak photochemical activity under increased cloud cover and active vertical dispersion under a low pressure system. However, the maximum $O_3$ concentrations during this period were somewhat high (similar to those in the normal period extraneous to the typhoon), possibly because of the relatively slow photochemical loss of $O_3$ by a $H_2O+O(^1D)$ reaction resulting from the low air temperature and low relative humidity. The lowest $O_3$ concentrations during the typhoon period were relatively high compared to the period before and after the typhoon, mainly due to the transport effect resulting from the strong nocturnal winds caused by the typhoon. In addition, the $O_3$ increase observed at night in Daegu and Busan was primarily caused by local wind conditions (e.g., mountain winds) and atmospheric stagnation in the wind convergence zone around inland mountains and valleys.

• Journal of Korea Water Resources Association
• /
• v.55 no.2
• /
• pp.147-157
• /
• 2022

The backward-facing step (BFS) is a benchmark geometry for analyzing flow separation occurred at the edge and resulting development of shear layer and recirculation zone that are occupied by turbulent flow. It is important to accurately reproduce and analyze the mean flow and turbulence statistics of such flows to design physically stable and performance assurance structure. We carried out 3D RANS computations with widely used, two representative turbulence models, k-ω SST and RNG k-ε, to reproduce BFS flow at the Reynolds number of 23,000 and the Froude number of 0.22. The performance of RANS computations is evaluated by comparing numerical results with an experimental measurement. Both RANS computations with two turbulence models appear to reasonably well reproduce mean flow in the shear layer and recirculation zone, while RNG k-ε computation results in about 5% larger velocity between the outer edge of boundary layer and the free surface above the recirculation zone than k-ω SST computation and experiment. Both turbulence models underestimate the shear stress distribution experimentally observed just downstream of the sharp edge of BFS, while shear stresses computed in the boundary layer downstream of reattachment point are agree reasonably well with experimental measurement. RNG k-ε modeling reproduces better shear stress distribution along the bottom boundary layer, but overestimates shear shear stress in the approaching boundary layer and above the bottom boundary layer downstream of the BFS.

• Journal of Hydrogen and New Energy
• /
• v.21 no.3
• /
• pp.227-240
• /
• 2010

Coal gasification is heading for a great future as one of the cleanest energy sources, which can produce not only electricity and heat, but also gaseous and liquid fuels from the synthesis. The work focuses on 300MW shell type one-stage entrained flow coal gasifier which is used in the Integrated coal Gasification Combined Cycle(IGCC) plant as a reactor. As constructing an IGCC plant is considerably complicated and expensive compared with a pulverized-coal power plant, it is important to determine optimum design factors and operating conditions using a computational fluid dynamics (CFD) model. In this study, the results of numerical calculations show that $O_2$/Coal ratio, 0.83, Steam/Coal ratio, 0.05, coal particle diameter, $100{\mu}m$, injection angle, $4^{\circ}$ (clockwise) are the most optimum in this research.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.219-219
• /
• 2021

서해안 중부 아산만 안쪽에 위치하는 평택·당진항에서 장래 개발 예정인 면적 6.9km²의 내항2공구 수역은 내항2공구 외곽호안 - 내항가호안 - 내항2공구 중앙 분리호안으로 둘러싸여 있으며, 투수성 제체인 내항가호안 사석 공극을 통하여 해수가 유통되어 조석 현상이 나타나고 있다. 2020년 8~9월의 2개월간 내항2공구 외곽호안 내·외측에서 조석 관측 결과, 2공구 수역의 최대 조차는 1.97m로서 외측 해역 최대 조차 9.79m의 20.1%이고 내·외측의 순간 수위차는 최대 5.82m에 달한다. 내항가호안은 내항2공구 개발이 거의 완료되는 시기까지 유지될 예정이므로 2공구 개발에 따른 내측 조차와 내·외측 수위차의 변화를 정확하게 예측하는 것은 내항가호안 제체 안전에 매우 중요하다. 이 연구의 목적은 장래 개발단계별 변화 예측에 앞서, 관측이 이루어진 2개월간의 실시간 내측 조석과 내·외측 수위차 시계열을 Delft3D-Flow를 이용하여 기 구축된 아산만 수치모델에서 재현하는 것이다. 내항가호안 제체 통과 유량은 내·외측 수위차에 비례하는 것으로 가정하고, 수위차 - 유량 관계식을 도출하였다. 수위차는 평택 조위관측소와 내항2공구 수역의 1분 간격 관측 조위로부터 산출하였고, 제체 통과 유량은 내측 조위(z, 평택항 DL 기준, m) - 수용적(V, 10⁶m³) 관계식으로 계산하였다. 내측 조위 - 수용적 관계식은 수심측량 성과로부터 V = 0.28z² + 3.73z + 2.96 (r²=1.00)으로 얻어졌다. 다양한 함수식의 적합성을 검토한 결과, 다음과 같은 수위차(𝚫z, m) - 제체 통과 유량(Q, m³/s) 관계식을 도출하였다. [내항가호안 내측으로 유입시] $Q_{IN}=\{\begin{array}{lll}{\exp}\{0.54\;{\ln}({\Delta}z)+6.00\}&&\text{; }{\Delta}z{\leq}1.8\\219.82{\Delta}z+158.56&&\text{; }{\Delta}z>1.8\end{array}\;\;(r^2=0.86)$ [내항가호안 외측으로 유출시] Q_OUT = -exp{0.44 ln(-𝚫z) + 5.70} (r²=0.59) 매 𝚫t 마다 제체 통과 유량을 계산하는 알고리즘을 Delft3D 소스 코드에 추가하고, 8개 분조 합성조석(M₂, S₂, K₁, O₁, N₂, K₂, P₁, Q₁)을 외력조건으로 설정하여 2개월간 조석 수치모델링을 수행하였다. 내항2공구 수역의 매 시별 조위 관측치와 모델치를 비교한 결과, 오차는 -0.37~0.37m의 범위이고, 오차 평균은 0.02m, 절대오차 평균은 0.08m로 상당히 정확하게 실시간 조위 변동을 모의하였다. 보정·검정된 이 모델을 이용하여 향후 내항2공구 개발에 따른 내측 조석과 내·외측 수위차 변화에 대한 예측모의를 진행할 예정이다.