• 열처리공학회지
• /
• 제9권3호
• /
• pp.212-218
• /
• 1996

To clarify the influence of precipitation microstructure and inclusion on the monotonic tensile fracture behaviors in 2090 alloy aged at $180^{\circ}C$, the detailed measurement of hardness, tensile strength, elongation and the observation of scanning electron micrography, transmision electron micrography have been carried out. The transgranular shear ductile fracture has been observed in specimen quenched after solution treatment at $500^{\circ}C$ for 45min. While the under-aged specimen was fractured in both transgranular shear ductile and intergranular fracture mode, the fracture mode of peak-aged and over-aged alloy was predominantly intergranular fracture. The fracture behavior of each ageing condition was influenced by the change of precipitation microstructural features. In the case of peak-aged and over-aged alloys, the coarse and heterogeneous slip band caused by both shearable nature of the ${\delta}^{\prime}(Al_3Li)$ precipitates and PFZ along the high angle grain boundary aid the localization of deformation, resulting in low energy intergranular fracture. It was also estimated that the fractured T-type intermetallic phases (inclusion) and the equilibrium ${\delta}$(AlLi) phases which were formed at grain boundaries palyed an important role in promoting intergranular fracture mode.

• 열처리공학회지
• /
• 제8권2호
• /
• pp.149-154
• /
• 1995

The alloying of 6.5wt % Silicon in iron decreases the magnetization and the anisotropy and minimizes the iron loss noticeably. But it is very difficult to make thin sheets because of its poor ductility which is due to an ordering reaction (body centered cubic to CsCI type crystal structure). However the ordering reaction can be suppressed by rapid solidification method. The cooling rate of rapidly solidified Fe-6.5wt % Si alloy is about $10^3K/s$ and rapidly solidified structure are fine structure, cellular structure, dendrite and equiaxed grain from surface. The precipitates of $DO_3$ Phase emerges on $B_2$ matrix and the coercive force was 0.51 Oe (50cycle, 15KGauss) in Fe-6.5wt% Si alloy which was processed by heat treatment of $1150^{\circ}C$ for 1hr in high vacuum.

• 한국자기학회지
• /
• 제9권3호
• /
• pp.166-172
• /
• 1999

본 연구에서는 마그네트론 스퍼터링 법으로 제작한 Mn-Ir/Ni-Fe/Zr/Si 다층막에서 Mn-Ir의 조성과 증착조건을 변화시키고 또한 Mn-Ir층의 두께를 조절한 후 자기적 특성과 미세구조에 대하여 고찰하였다. Mn-22at% Ir의 조성에서 219Oe의 가장 높은 Hex와 30Oe의 낮은 Hc를 얻을 수 있었다. 초기진공도가 3.0$\times$10-6Torr 이상 일때는 교환이방성이 사라지게 되었으며 이것은 Mn-Ir의 비정질화와 결정립미세화에 의한 것으로 판단된다.

• 한국주조공학회지
• /
• 제40권2호
• /
• pp.7-15
• /
• 2020

The high-temperature stability of Mg-8.0Zn-1.6Y (wt.%) alloys upon the addition of Ca has been investigated by characterizing the ignition temperature, microstructure, tensile and creep properties. The ignition temperature increases with an increase in the Ca content, indicating that an addition of Ca enhances the ignition resistance of the Mg-Zn-Y alloy. The as-cast microstructures of all tested alloys mainly consisted of the dendritic α-Mg matrix and I-phase (Mg₃Zn₆Y) at the grain boundaries. In the Ca-added Mg-8.0Zn-1.6Y alloys, the Ca₂Mg₆Zn₃ phase forms, with this phase fraction increasing with an increase in the Ca contents. However, a high volume fraction of the Ca₂Mg₆Zn₃ phase rather deteriorates the mechanical properties. Therefore, a moderate amount of Ca element in Mg-8.0Zn-1.6Y alloys is effective for improving the tensile and creep properties of the Mg-Zn-Y alloy. The Mg-8.0Zn-1.6Y-0.3Ca alloy exhibits the highest tensile strength and the lowest creep strain among the alloys investigated in the present study. The creep resistance of Mg-Zn-Y-Ca alloys depends on the selection of the secondary solidification phase; i.e., when Ca₂Mg₆Zn₃ forms in an alloy containing a high level of Ca, the creep resistance deteriorates because Ca₂Mg₆Zn₃ is less stable than the I-phase at a high temperature.

• 한국결정성장학회지
• /
• 제22권4호
• /
• pp.178-182
• /
• 2012

결정립 성장은 여러 가지 재료의 성질에 미치는 큰 영향으로 재료공학에서 매우 중요하다. 그래서 본 연구에서는 PC에서 대규모 상장 모델을 사용하여 이방성 결정립 계면에너지의 2차원 결정립 성장에 미치는 효과를 조사하였다. 컴퓨터 모사에서는 $2000{\times}2000$의 그리드 시스템과 약 7300개의 초기 결정립 개수가 사용되었다. 결정립계 에너지의 이방성의 비, ${\sigma}_{max}/{\sigma}_{min}$는 1부터 3까지 변경되었다. 이방성이 증가함에 따라 결정립 성장 지수, n은 2.05에서 2.37로 증가하였다. 결정립 크기의 분포는 등방성인 경우에는 중앙에 평탄한 영역을 보였으나 이방성의 경우에는 중앙의 평탄한 영역이 사라지고 매우 느리게 사라지는 작은 결정립에 기인하여 작은 결정립 크기의 분포가 약간 증가하였다. 마지막으로 모사된 결정립 미세구조가 이방성에 따라 비교, 분석되었다.

• KIEE International Transactions on Electrophysics and Applications
• /
• 제12C권4호
• /
• pp.220-224
• /
• 2002

The electromagnetic properties and thermal behavior of Mn-Zn ferrite cores for the blocking filter of PLC application were investigated as the function of additives. The highest density and permeability were 4.98 g/㎤ and 8,221, respectively and were obtained to the specimen with composition of MnO 24 mol%, ZnO 25 mol% and Fe$_2$O$_3$51 mol%, added MoO$_3$ of 400 ppm, SiO$_2$ of 100 ppm, and CaO of 200 ppm. The uniform grains were organized, and the microstructures were compacted due to reduction of pores in the specimen. The permeability was increased up to 13,904 as the temperature of specimen increased to 110。C. However, it was decreased precipitously under 100 over 110。C. The exothermic behavior was observed in the frequency range from 1 kHz to 1 MHz, and the maximum temperature of specimen was 102。C at 1 MHz. In the consequence, the Mn-Zn ferrite core developed in this research will maintain the stable electromagnetic properties since the temperature of ferrite core rose to 93 。C in the range of 100 kHz to 450 kHz bandwidth qualified for PLC. The blocking filters were designed for single phase and three phases using the in-line and non-contact core. The best attenuation ratios of -46.46 dB and -73.9 dB were measured in the range of 100 kHz to 450 kHz bandwidth, respectively.

• 한국전기전자재료학회논문지
• /
• 제16권6호
• /
• pp.490-495
• /
• 2003

The electromagnetic properties and thermal behavior of Mn-Zn ferrite cores for the blocking filter of Power Line Communication(PLC) application were investigated as a function of additives. The highest density and permeability were 4.98 g/$\textrm{cm}^2$ and 8,221, respectively and were obtained to the specimen with composition of MnO 24 mol%, ZnO 25 mol% and Fe$_2$O$_3$ mol%, added MoO$_3$ of 400 ppm, SiO$_2$ of 100 ppm, and CaO of 200 ppm. The uniform grains were organized, and the microstructures were densified due to reduction of pores in the specimen. The permeability was increased up to 13,904 as the temperature of specimen increased to 110$^{\circ}C$. However, it was decreased precipitously under 100 over 110$^{\circ}C$. The exothermic behavior was observed in the frequency range from 1 kHz to 1 MHz, and the maximum temperature of specimen was 102$^{\circ}C$ at 1 MHz. In the consequence, the Mn-Zn ferrite core developed in this research will maintain the stable electromagnetic properties since the temperature of ferrite core rose to 93$^{\circ}C$ in the range of 100 kHz to 450 kHz bandwidth qualified for PLC. The blocking filters were designed for single phase and three phases using the in-line and non-contact core. The best attenuation ratios of -46.46 dB and -73.9 dB were measured in the range of 100 kHz to 450 kHz bandwidth, respectively.

• 한국표면공학회지
• /
• 제51권3호
• /
• pp.164-171
• /
• 2018

In this study, we have fabricated pure titanium (Ti)/hydroxyapatite (HA) double layer coating on medical grade PEEK from magnetron sputtering system, an investigation was performed whether the surface can be had more improve bio-active for orthopedi/dental applications than that of non-coated one. Pure Ti and HA coating layer were obtained by a radio-frequency and direct current power magnetron sputtering system. The microstructures surface, mechanical properties and wettability of the pure Ti/HA double layer deposited on the PEEK were analyzed by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), nano-indentation, and contact angle test. According to the EDS and XRD results, the composition and crystal structure of pure Ti and HA coated surface were verified. The elastic modulus and hardness value were increased by pure Ti and HA coating, and the pure Ti/HA double layer coating surface has the highest value. The contact angle showed higher value for pure Ti/HA double layered coating specimens than that of non-coated (PEEK) surface.

• 한국지반공학회논문집
• /
• 제27권11호
• /
• pp.93-101
• /
• 2011

X-ray micro-CT를 이용한 지반재료 내부 미세구조 및 공극구조의 정밀한 이미지 처리는 종종 이미지 내에 원천적으로 포함되는 화상결함으로 인해 제약된다. 본 논문에서는 X-ray micro-CT 이미지에 가장 일반적으로 나타나는 화상결함인 패임(영상 외곽과 중심부의 명암 차이) 및 동심원상(영상 중심으로부터 방사방향으로 연속적으로 나타나는 원)을 제거할 수 있는 이미지 보정 기법을 제시한다. 결함 제거는 좌표 변환법, 정규화 및 2차원 푸리에 변환에 의한 저역 통과 필터링 기법의 순차적 적용을 통해 이루어진다. 이미지 처리 기법의 효과를 다공성 현무암의 CT 이미지에서 화상결함들을 제거하고 이진화 후 적층하여 3차원 공극 구조를 추출하는 과정을 통해 설명하였다. 패임 및 동심원상 결함을 제거한 이미지와 원본 이미지의 비교 결과 결함 제거는 대상 재료 공극률의 과대평가를 방지할 수 있으며, 따라서 화상결함의 적절한 보정은 X-ray CT의 지반재료 적용 시 필수적인 과정으로 판단된다.

• 한국세라믹학회지
• /
• 제40권3호
• /
• pp.268-272
• /
• 2003

직류 마그네트론 스퍼터링법을 이용하여 증착압력과 기판온도변화에 따른 텅스텐 박막의 미세구조 변화에 대하여 연구하였다. 기판온도 40$0^{\circ}C$에서 증착 압력의 감소에 따라 텅스텐 박막의 미세구조가 zone I에서 zone T로 변화하였다. 텅스텐 박막의 미세구조 비저항과 결정배향성은 상관관계를 보였으며. 미세구조가 zone T 영역에서 낮은 비저항(10$\times$$10^{-6}$ $\Omega$-cm) 과 99%의 (110)면 우선 배향성을 나타내었다. zone T 영역에 해당하는 미세구조를 지니는 텅스텐 박막을 이용한 박막형 공진기는 텅스텐 박막의 높은 탄성저항과 매끈한 표면으로 인해 494의 $Q_{s}$와 5.50%의 $K_{eff}$$^{2}$ 값의 우수한 공진특성을 보였다....