• Journal of the Korean Society of Visualization
• /
• v.5 no.2
• /
• pp.26-32
• /
• 2007

Stereoscopic PTV and Stereoscopic-PIV measurements have been carried out for the studies of the wake of a ship's propeller. Stereoscopic photogrammetry based on a 3D-PTV principle was introduced using two high-definition cameras(1k x 1k, 30Hz). The arrangement of the two cameras was based on angular position. The pair-matching of the three-dimensional velocity vectors were based on Genetic Algorithm based 3D-PTV technique. The results obtained by both measurement systems have been compared at the advance ratio J=0.88(290 rpm, d=54 mm). Turbulent properties have also been compared each other at the same condition.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1772-1777
• /
• 2004

The performances of the newly constructed Stereoscopic PTV and Stereoscopic PIV which had been completed based on a 3D-PTV principle are tested using the Standard Images. Virtual images were produced for the benchmark tests of the constructed two Stereoscopic techniques. The arrangement of the two cameras was based on angular position. The calibration of cameras and the pair-matching of the three-dimensional velocity vectors were based on Genetic Algorithm based 3D-PTV technique. The Standard data of LES are on the impinged jet proposed by VSJ. It is shown that the results obtained by Stereoscopic PTV have better reliability than those by Stereoscopic PTV.

• Journal of Sensor Science and Technology
• /
• v.20 no.2
• /
• pp.77-81
• /
• 2011

This paper presents a single-pole eight-throw(SP8T) switch based on proposed a radio-frequency(RF) microelectromechanical systems (MEMS) switches. The proposed switch was driven by a double stop(DS) comb drive, with a lateral resistive contact. Additionally, the proposed switch was designed to have tapered signal line and bi-directionally actuated. A forward actuation connects between signal lines and contact part, and the output becomes on-state. A reverse actuation connects between ground lines and contact part, and the output becomes off-state. The SP8T switch of 3-stage tree topology was developed based on an arrangement of the proposed RF MEMS switches. The developed SP8T switch had an actuation voltage of 12 V, an insertion loss of 1.3 dB, a return loss of 15.1 dB, and an isolation of 31.4 dB at 6 GHz.

• ETRI Journal
• /
• v.45 no.4
• /
• pp.581-593
• /
• 2023

This paper proposes four-ring slot resonator-based MIMO antennas of 75×150 mm² without and with CSRR structures in the sub-6-GHz range. These orthogonal-fed antennas have shown diverse characteristics with dual polarization. L-shaped parasitic structures have increased the isolation (i.e., >40 dB) in the single-element antenna over the band of 3.4 GHz-3.8 GHz. A set of three CSRR structures in the MIMO antenna reduced the coupling between antenna ports placed in an inline arrangement and enhanced the isolation from 12 dB to 20 dB and the diversity characteristics. The S-parameters of both MIMO antennas are measured and used to evaluate MIMO parameters like ECC, TARC, MEG, and channel capacity loss. The simulation results show the variations in the gain and directivity on exciting linear and dual polarizations. The diversity performance of the reported MIMO antennas is suitable for 5G applications.

• Spatial Information Research
• /
• v.14 no.4 s.39
• /
• pp.391-401
• /
• 2006

We propose a method for geographically enhanced representation of social networks and implement a Web-based 3D visualization of geographical contexts in social networks. A renovated social network graph is illustrated by using two key components: (i) GWCMs (geographically weighted centrality measures) that reflect the differences in interaction intensity and spatial proximity among nodes and (ii) MSNG (map-integrated social network graph) that incorporates the GWCMs and the geographically referenced arrangement of nodes on a choroplethic map. For the integrated 3D visualization of the renovated social network graph, we employ X3D (Extensible 3D), a standard 3D authoring tool for the Web. An experimental case study of regional R&D collaboration provides a visual clue to geographical contexts in social networks including how the social centralization relates to spatial centralization.

• The Journal of the Korea Contents Association
• /
• v.11 no.9
• /
• pp.106-117
• /
• 2011

The purpose of this study is to examine factors that affect 3D stereoscopic movie audiences' satisfaction in Korea, and to provide strategic solutions to improve audiences' satisfaction. According to study about movie audiences' satisfaction, factors that affect movie audiences' satisfaction are separated to movie internal factors, movie environmental factors and movie audience factors. And leverage of movie internal factors is bigger than either. But 3D stereoscopic movie is different from ordinary movie in shooting, screening, seeing and recognizing method. So it is expected that movie environmental factors and audience factors' influence is bigger than internal factors. So this study carried out a survey targeting 3D stereoscopic audiences. Main result of this study are shown as follows. First, the method to reduce visual fatigue is necessary for satisfaction. Second, it is required that improvement method of seat arrangement to provide high quality 3D stereoscopic contents. Third, level of 3D stereoscopic movies' price need to adjust to valid level.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.2
• /
• pp.159-165
• /
• 2007

The Characteristics of the flowfield around two circular cylinders in tandem arrangement was investigated by PIV. Strouhal numbers. velocity vectors and velocity profiles were observed at centre-to-centre space ratios of P/D= 1.5. 2.0 and 2.5, and Reynolds number of $Re=3.0{\times}10^3{\sim}5.0{\times}10^3$. As the results the Strouhal numbers measured in the rear region of the cylinder of wake side were decreased with the space ratios. The flow between two cylinders was almost stagnated and the size of the stagnated region was larger in the close side than in the far side of the front cylinder. The direction of vortex between two cylinders was opposed each other with the small difference(${\alpha}\;{\pm}1.0^{\circ}$) of the attack angle ${\alpha}$.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.20 no.3
• /
• pp.369-375
• /
• 2017

One of good DF(Direction Finding) methods is based on TDOA(Time Difference of Arrival) estimation when finding underwater moving target. For small DF error, high time resolution A/D(Analog-to-digital) conversion board and long baseline are needed. But the result of sea trial about close-range and high speed moving target, spatial correlation coefficient and appeared poor properties below 0.3 when hydrophone arrangement are separated over 6 ${\lambda}$ because of underwater fading channel. And we also find out that the distance between hydrophone should be under 4 ${\lambda}$ apart to take advantage of spatial correlation coefficient gain and performance of DF in underwater moving channel environments.

• Journal of Advanced Research in Ocean Engineering
• /
• v.2 no.3
• /
• pp.150-157
• /
• 2016

When blocks are supported on a dock, huge reaction forces concentrated at the supports cause structural damage owing to local stress concentrations. Thus, the supports should be arranged to avoid local failure from the reaction forces by redistributing those forces. Docking analyses to determine the proper blocks and their support arrangements are introduced so that the local stresses are minimized to warrant the safety of the docking supports. Local stresses enforced by the support arrangement should be evaluated by finite element analysis (FEA). However, it is difficult to consider an accurate 3D geometry of the blocks in the finite element model because the structural design information is too complicated to determine within several days using the FEA model. This paper presents a simplified FE model to evaluate the safety of the arrangement of supports using a simplified grillage element. The grillage element can be efficiently used to obrain the reaction forces in docking analysis becasuse the reaction forces at the supports are enough to assess the safety of block. Since a simplified grillage model of the entire ship cannot accurately calculate the local stresses, an optimized modeling method based on the grillage element was introduced. The local reaction forces obtained by the proposed approach and three-dimensional FEA were discussed for typical types of ships. It is shown that the reaction forces obtained by the present grillage model are in reasonably good agreement with the FEA model.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.9 no.3
• /
• pp.378-385
• /
• 1998

A three-dimensional finite difference time domain (3-D FDTD) algorithm of calculation for the characteristics of coaxial-to-cavity filter including a discended probe and a tuning post is presented. In the arrangement the inner coaxial conductor protrudes into the cavity and operates as a probe radiator. And the height of the rectangular tuning post determines the resonant frequency. The validation of this method is confirmed by comparing the calculated values with experimental results for the designed filter.