• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2011년도 제45차 학술발표회
• /
• pp.42-42
• /
• 2011

To evaluate the Hwangsu spring as natural mordants effect on dyeing. The natural mordants effect of Hwangsu spring were analyzed by pH, temperature, trace elements, organic matter and color fastness. Hwangsu spring having pH 2.42 and $14.4^{\circ}C$ was harvested at the end of September, in Yeongcheon (Gyeongbuk Province, Korea) and left on a $0^{\circ}C$ and $25^{\circ}C$ before use. Hwangsu spring during storage at $25^{\circ}C$ turned brown by photochemical reaction. The Result of ICP analysis, it contained Fe(414.9 ppm), Al(88.9 ppm), Mn(4.9 ppm) and observed character by water analysis. Dyeing and post-mordant procedure; Cotton(KS K 0905) were dyed with clove powder for 30 min at $70^{\circ}C$. Hwangsu spring, Aluminium Sulfate $14-18H_20(Al_2(SO_4)_3{\cdot}14-18H_2O)$, Iron Sulfate Heptahydrate($FeSO_4{\cdot}7H_2O$) were used by post mordant at the same ratio. The dyed fabrics were treated with 20% each mordant solution at $25^{\circ}C$ for 10min. Comparison with a reproduced chemical mordant, the K/S values of cotton fabrics dyed with Hwangsu sping were increased.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.135-138
• /
• 2004

Since the upsetting type is superior to an extrusion type to get the dimensional accuracy of cold forged spur gear, the upsetting type process far spur gear cold forging has been studied. FE analysis of upsetting type process fur spur gear cold forging was performed to investigate about flow pattern of workpiece and die stress. To analyze the elastic characteristics of die, both rigid and elastic material model were used during loading stage. Under-filled defects were detected In lower portions of spur gear forged by upsetting type in experimental. When the elastic material model for die was used, the under-filled defects could be predicted. On the other hand, if the material model of die was rigid, the defects could not been presented because the die deflection was not considered.

• 한국CDE학회논문집
• /
• 제10권1호
• /
• pp.61-69
• /
• 2005

In the global ship structure and vibration analysis, the FE(finite element) analysis model is required in the early design stage before the 3D CAD model is defined. And the analysis model generation process is a time-consuming job and takes much more time than the engineering work itself. In particular, ship structure has too many associated structural members such as stringers, stiffness and girders etc. These structural members should be satisfied as the constraints in analysis modeling. Therefore it is necessary to support generation of analysis model with satisfying these constraints as an automatic manner. For the effective support of the global ship analysis modeling, a method to generate analysis model using initial design information within ship design process, that hull form offset data and compartment data, is developed. In order to easily handle initial design information and FE model information, flexible data structure is proposed. An automatic quadrilateral mesh generation algorithm using initial design information to satisfy the constraints imposed on the ship structure is also proposed. The proposed data structure and mesh generation algorithm are applied for the various type of vessels for the usability test. Through this test, we have verified the stability and usefulness of this system including mesh generation algorithm.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.172-175
• /
• 2005

The numerical simulation is performed for the acoustic emission and the wave propagation due to fiber breakage in single fiber composite plates by the finite element transient analysis. The acoustic emission and the following wave motions from a fiber breakage under a static loading is simulated to investigate the applicability of the explicit finite element method and the equivalent volume force model as a simulation tool of wave propagation and a modeling technique of an acoustic emission. For such a simple case of the damage event under static loading, various parameters affecting the wave motion are investigated for reliable simulations of the impact damage event. The high velocity and the small wave length of the acoustic emission require a refined analysis with dense distribution of the finite element and a small time step. In order to fulfill the requirement for capturing the exact wave propagation and to cover the 3-D simulation, we utilize the parallel FE transient analysis code and the parallel computing technology.

• Restorative Dentistry and Endodontics
• /
• 제33권1호
• /
• pp.28-38
• /
• 2008

본 연구는 3차원 유한요소 분석법적 연구를 통해 쐐기형 비우식성 치경부병소의 복합레진 수복물에서 다른 탄성계수를 가진 복합레진의 수복과 와동의 형태와 응력의 방향에 따른 응력분포의 영향에 대해 알아보고자 하였다. 발거된 상악 제2소구치를 Micro-CT로 스캔한 후 3D-DOCTOR로 3차원유한요소 모형을 제작하였다. 제작된 소구치 모형에 쐐기형 와동과 변형시킨 와동을 형성하고 각 와동을 탄성계수가 서로 다른 혼합형 복합레진 또는 흐름성 복합레진으로 수복하였다. 수복 전, 후 협측교두와 설측교두에 500N의 하중을 가한 후 응력분포를 ANSYS 프로그램을 이용하여 주 응력 분석법으로 평가한 바 다음과 같은 결과를 얻었다. 1. 수복 전 응력은 근심측 백악법랑경계와 와동저 선각부에 집중되었으며 최대응력은 근심협측우각부에서 나타났다. 2. 와동수복 후 와동저 선각의 응력은 현저히 감소했으나 치경부측 변연의 응력은 수복전보다 증가하였다. 3. 쐐기형태의 병소의 수복 시 와동저 선각부는 탄성계수가 높은 재료가 유리하고 치경부측 변연은 탄성계수가 낮은 재료가 유리하였다. 4. 와동저 선각부를 둥글게 변화시키는 것은 압축응력은 감소시키지 않으나 인장응력은 감소시켰다.

• 한국산업융합학회 논문집
• /
• 제27권4_2호
• /
• pp.833-840
• /
• 2024

According to recent data from the Korea Meteorological Administration(KMA), the frequency of typhoons around the Korea Peninsula is almost unchanged, but the intensity is on the rise due to climate change. A typhoon that has become so powerful can cause partial or complete damage to the traffic signal structures, limiting the operation of the vehicle and causing traffic congestion. If the traffic signal structure fails to function properly due to the influence of the typhoon, not only the v ehicle operation will be disrupted, but also direct damage to the traffic signal structure will occur. In addition, if the social overhead cost of traffic congestion is included, the recovery cost caused by the typhoon will increase to an extent that it is difficult to estimate. Therefore, in this study, a wind tunnel experiment was performed by producing a wind tunnel model of an existing fixed traffic signal structure and a traffic signal structure in which signs and traffic lights are hinged. Also, The fixed and hinge structures were modeled as 3D finite elements, and wind-resistant analysis was performed by wind speed, and, wind-resistant safety of traffic signal structures were analyzed and examined through wind-resistant analyses. From the comparative analysis of the results of experiment and FE analysis, it was known that the stress reduction rate of the hinge connection structure was at least 30% compared to that of the fixed connection structure from the results of the wind tunnel experiment and FE analysis. And As a result of finite element analysis for the maximum design wind speed of 50m/s, it was found that the maximum stress generated in the existing structure exceeded all the yield stress, but the maximum stress of the hinge connection structure was within the yield stress. Finally The hinge connection structure showed a relatively large stress reduction rate as the wind speed increased and the length of the lateral beam was shorter at the same wind speed.

• 전기학회논문지
• /
• 제57권3호
• /
• pp.375-383
• /
• 2008

This paper deals with reduction and analysis of cogging torque for permanent magnet synchronous generators with multi-pole rotor for wind power applications. Open-circuit field solutions are derived using a magnetic vector potential and a two-dimensional (2-d) polar coordinate systems. On the basis of derived open-circuit field solutions and 2-d permeance functions, we also derive open-circuit field solutions considering stator slotting effects. By using open-circuit field solutions considering stator slotting effects and energy variation methods, this paper analytically predicts the cogging torque considering skew effects. All analytical results are shown in good agreement with those obtained from finite element (FE) analyses. In order to reduce the cogging torque, by predicting the variation of the cogging torque according to pole arc/pitch ratio using analytical and FE methods, pole arc/pitch ratio which makes the cogging torque minimum are determined. However, we confirm that measured value for cogging torque of the PMG with determined pole arc/pitch ratio is twice higher than predicted value. Therefore, the reason for an error between measured and predicted cogging torque is discussed in terms of a shape of PMs and is proved experimentally.

• Restorative Dentistry and Endodontics
• /
• 제33권3호
• /
• pp.184-197
• /
• 2008

본 연구는 3차원 유한요소분석법적 연구를 통해 쐐기형 비우식성 치경부병소의 복합레진수복에서 다른 탄성계수를 가진 복합레진의 혼합수복이 5급 수복물의 응력분포에 미치는 영향에 대해 알아보고자 하였다. 발거된 상악 제2소구치를 Micro-CT로 스캔한 후 3D-DOCTOR로 3차원유한요소 모형을 제작하였다. 제작된 소구치 모형에 쐐기형 와동과 변형시킨 와동을 형성하고 각 와동을 탄성계수가 서로 다른 혼합형 복합레진 또는 흐름성 복합레진으로 수복하였다. 수복 전, 후 협측교두와 설측교두에 500N의 하중을 가한 후 응력분포를 ANSYS 프로그램을 이용하여 주 응력 분석법으로 평가한 결과 치아 및 수복물에 위해한 인장응력을 고려할 때 탄성계수가 높은 재료로 와동저선각을 수복하고 교합측변연과 치경부측 변연은 탄성계수가 낮은 재료로 수복하는 혼합수복법이 쐐기형 비치경부병소의 수복에 있어 가장 유리하였다.

• 자원환경지질
• /
• 제28권3호
• /
• pp.213-220
• /
• 1995

Geochemistry of stream water and sediment collected in the vicinity of the Donghae coal mine in the Samchuk coalfied were investigated in order to evaluate the environmental impacts of acid mine drainage. The pH of stream water ranges from 2.85(at 2 km away from the mine) to 7.92(at uncontaminated tributary). The main cation and anion species in the upper stream are $Ca^{2+}$ and $SO_{4}{^2-}$, respectively. The level of pH and the amount of $HCO^{3-}$ in stream water increase to the downstream and where uncontaminated small tributaries are joining, and in the area covered with limestone. From the results of thermodynamic calculation, the main forms of iron in stream water are estimated as $Fe^{2+}$ and $FeSO_{4}{^0}$, and most of them could be precipitated as FeO(OH) with increase of pH. The white precipitates in stream sediments particularly found around the coal mine are proved to be $Al(OH)_3$ by XRD and XRF analysis. As a result of investigation for seasonal variation of AMD, the level of pH decreased and conductivity increased in dry season.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.156-156
• /
• 2017

In this work, analysis of biocompatible TiO2 oxide multilayer by the XPS depth profiling was researched. the manufacture of the TiO2 barrier-type multilayer was accurately performed in a mixed electrolyte containing HAp, Pd, and Ag nanoparticles. The temperature of the solution was kept at approximatively $32^{\circ}C$ and was regularly rotated by a magnetic stirring rod in order to increase the ionic diffusion rate. The manufactured specimens were carefully analyzed by XPS depth profile to investigate the result of chemical bonding behaviors. From the analysis of chemical states of the TiO2 oxide multilayer using XPS, the peaks are showed with the typical signal of Ti oxide at 459.1 eV and 464.8 eV, due to Ti 2p(3/2) and Ti 2p(1/2), respectively. The Pd-3d peak was split into Pd-3d(5/2) and Pd-3d(3/2)peaks, and shows two bands at 334.7 and 339.9 eV for Pd-3d3 and Pd-3d5, respectively. Also, the peaks of Ag-3d have been investigated. The chemical states consisted of the O-1s, P-2p, and Ti-2p were identified in the forms of PO42- and PO43-. Based on the results of the chemical states, the chemical elements into the TiO2 oxide multilayer were also inferred to be penetrated from the electrolyte during anodic process.The structure characterization of the modified surface were performed by using FE-SEM, and from the result of biological evaluation in simulated body fluid(SBF), the biocompatibility of TiO2 oxide multilayer was effective for bioactive property.