• Wind and Structures
• /
• v.30 no.4
• /
• pp.433-450
• /
• 2020

The strong turbulence characteristic of typhoon not only will significantly change flow field characteristics surrounding the large-scale wind turbine and aerodynamic force distribution on surface, but also may cause morphological evolution of coast dune and thereby form sand storms. A 5MW horizontal-axis wind turbine in a wind power plant of southeastern coastal areas in China was chosen to investigate the distribution law of additional loads caused by wind-sand coupling movement of coast dune at landing of strong typhoons. Firstly, a mesoscale Weather Research and Forecasting (WRF) mode was introduced in for high spatial resolution simulation of typhoon "Megi". Wind speed profile on the boundary layer of typhoon was gained through fitting based on nonlinear least squares and then it was integrated into the user-defined function (UDF) as an entry condition of small-scaled CFD numerical simulation. On this basis, a synchronous iterative modeling of wind field and sand particle combination was carried out by using a continuous phase and discrete phase. Influencing laws of typhoon and normal wind on moving characteristics of sand particles, equivalent pressure distribution mode of structural surface and characteristics of lift resistance coefficient were compared. Results demonstrated that: Compared with normal wind, mesoscale typhoon intensifies the 3D aerodynamic distribution mode on structural surface of wind turbine significantly. Different from wind loads, sand loads mainly impact on 30° ranges at two sides of the lower windward region on the tower. The ratio between sand loads and wind load reaches 3.937% and the maximum sand pressure coefficient is 0.09. The coupling impact effect of strong typhoon and large sand particles is more significant, in which the resistance coefficient of tower is increased by 9.80% to the maximum extent. The maximum resistance coefficient in typhoon field is 13.79% higher than that in the normal wind field.

• Journal of the Korean Ceramic Society
• /
• v.41 no.9
• /
• pp.709-714
• /
• 2004

The additive of low temperature sintering in Mn-doped PMN-PZT known as high piezoelectric materials was studied in this experiment. B$_2$O$_3$ was used for the additive of low temperature sintering. The effects of sintering temperature in dielectric, and piezoelectric properties were investigated with the amounts of B$_2$O$_3$. Sintered density was increased in comparison with no addition and under 2wt％ B$_2$O$_3$ and lower sintering temperature than 100$0^{\circ}C$. Therefore, in the low sintering temperature, the densification was improved by the addition of the B$_2$O$_3$. However, the sintering density was lower than that of the main composition in the case of the sintered at over 10$50^{\circ}C$. Dielectric constant with the addition of B$_2$O$_3$ was evaluated. The dielectric constant was 1000 2 wt％ of B$_2$O$_3$ and sintered at 100$0^{\circ}C$. Under 2wt％ of B$_2$O$_3$, the electromechanical coupling factor and the piezoelectric constant were not so much decreased. The electromechanical coupling factor and the piezoelectric constant were 50％ and 300(${\times}$10$^{-12}$ C/N) respectively. The mechanical quality factor was increased with B$_2$O$_3$. The mechanical quality factor was 1700 at 0.5wt％ B$_2$O$_3$ and sintered at 110$0^{\circ}C$. Dielectric loss was less than 0.5％ regardless of the amount of B$_2$O$_3$.

• Journal of the Korean Ceramic Society
• /
• v.54 no.6
• /
• pp.530-534
• /
• 2017

The figures of merit in the on-resonance and off-resonance conditions ($FOM_{on}$ and $FOM_{off}$) for the piezoelectric energy harvester (PEH) were measured and compared in $[(K_{0.485}Na_{0.515})_{1-X}Li_X](Nb_{0.99}Ta_{0.01})O_3$ (x = 0.04 ~ 0.09) (KNLNT) ceramics with various Li contents. The crystal structure of CuO-doped KNLNT ceramics changes from orthorhombic to tetragonal around the Li fraction of 0.065. The stable temperature range for the tetragonal phase widens to both higher and lower temperatures as Li is substituted. The piezoelectric charge constant ($d_{33}$), electromechanical coupling factor ($k_p$) and mechanical quality factor ($Q_m$) have maximum values at the Li fraction between 0.055 and 0.065 where the phase boundary lies between the orthorhombic and tetragonal phases. Both $FOM_{on}$ and $FOM_{off}$ have peak values around the phase boundary but the peak compositions are not exactly coincided. The optimal Li fraction in the KNLNT ceramic for a PEH application was found to be between 0.055 and 0.065.

• Journal of electromagnetic engineering and science
• /
• v.10 no.3
• /
• pp.92-98
• /
• 2010

A new wideband bandstop filter(BSF) with a sharp roll-off characteristic is introduced in a stripline structure in this paper. The BSF consists of two sections: the first is two capacitively coupled $\lambda/4$ short-circuited lines with opposite ground positions, while the second is a capacitively coupled $\lambda/4$ short-circuited line. The BSF provides three transmission zeros within the stopband and better than 22 dB rejection over the whole wireless local area network (WLAN) band from 5.15 to 5.825 GHz. The BSF, cascaded to an U.S. ultra-wideband(UWB: 3.1~10.6 GHz) band-pass filter(BPF), is simulated with HFSS and realized with low-temperature co-fired ceramic(LTCC) green tape with a dielectric constant of 7.8. The measurement results agree well with the HFSS simulation results. The size of the UWB BPF including the BSF is $3{\times}6.3\times0.45\;mm^3$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.1
• /
• pp.44-51
• /
• 2000

We have analyzed optical matched filters considering the third order signals in the optical code division multiple access (CDMA) system based on optical series coupler access encoder (SCAE) and series coupler access decoder (SCAD). In previous studies, the performance evaluation of the optical CDMA system using SCAE and SCAD was not sufficiently accurate because they analyzed system performance only considering the first order signals. Since optical SCAE and SCAD intrinsically have high order signals of various patterns as the number of coupler increases, they change auto- and cross-correlation intensities. Thus, it is necessary to investigate properties of the third order signals so that we may analyze the exact performance of system. In this paper, we mathematically interpret the optical signals up to the third order, and analyzed the effects of th third order signals on auto- and cross-correlation intensities. In result, as ${\alpha}$(coupling coefficient) value increases, the intensity of the third order signals increases. It is found that the peak to side-lobe ratio considering the third order signals is degraded by 3.75 dB at N(coupler number)=5 and ${\alpha}$=0.5. Also if threshold value in receiver is set by main-lobe peak of the first order signals, it is found that the number of users in an optical CDMA system is limited because the intensity peak of side-lobes is raised by the third order signals.

• Advances in aircraft and spacecraft science
• /
• v.4 no.1
• /
• pp.1-19
• /
• 2017

Fatigue life prediction of a multi-row countersunk riveted lap joint was performed numerically. The stress and strain conditions in a highly stressed substructure of the joint were analysed using a global/local finite element (FE) model coupling approach. After validation of the FE models using experimental strain measurements, the stress/strain condition in the local three-dimensional (3D) FE model was simulated under a fatigue loading condition. This local model involved multiple load cases with nonlinearity in material properties, geometric deformation, and contact boundary conditions. The resulting stresses and strains were used in the Smith-Watson-Topper (SWT) strain life equation to assess the fatigue "initiation life", defined as the life to a 0.5 mm deep crack. Effects of the rivet-hole clearance and rivet head deformation on the predicted fatigue life were identified, and good agreement in the fatigue life was obtained between the experimental and the numerical results. Further crack growth from a 0.5 mm crack to the first linkup of two adjacent cracks was evaluated using the NRC in-house tool, CanGROW. Good correlation in the fatigue life was also obtained between the experimental result and the crack growth analysis. The study shows that the selected methodology is promising for assessing the fatigue life for the lap joint, which is expected to improve research efficiency by reducing test quantity and cost.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.100-102
• /
• 2001

In this paper, the piezoelectric and dielectric properties of $Pb(Zr_xTi_{1-x)O_3$ - $Pb(Co_{1/3}Nb_{1/3})O_3)$ piezoelectric ceramics have been investigated as a function of Zr/Ti mole ratio. From the results, when Zr/Ti mole ratio is 49/51, electromechanical coupling coefficient($k_p$), piezoelectric strain constant($d_{33}$) mechanical quality factor($Q_m$), and Permittivity(${{\varepsilon}_{33}}^T/{\varepsilon}_0$) is 64[%], 469[PC/N], 360 and 2000, respectively. Morphotropic Phase Boundary is Zr/Ti mole ratio(49/51) from XRD analysis. Also. From SEM observation, when sintering temperature is 1150[$^{\circ}C$], grain size is about $1{\sim}2[{\mu}m]$ and maximum sintering density is 7.85[$g/cm^3$].

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.11a
• /
• pp.33-34
• /
• 2005

In this study, in odor to develop low temperature sintering multilayer piezoelectric actuator and ultrasonic vibrator, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3$ and $Na_2CO_3$ as sintering aids and their piezoelectric and dielectric characteristics were investigated according to the addition of dopant CuO and $Fe_2O_3$, respectively. The CuO added PMN-PNN-PZT ceramics improved mechanical quality factor Qm due to the acceptor doping effect. And also, $Fe_2O_3$ reacted as softner in this composition system in addition to the increase of grain size and sinterability. Taking into consideration electromechanical coupling factor kp of 0.62, dielectric constant $\varepsilon_r$, of 1275, Piezoelectric $d_{33}$ constant of 377[pC/N] and mechanical quality factor Qm of 975, it was concluded that the ceramics with the $Fe_2O_3$, added composition sintered at 900[$^{\circ}C$] were best for the multilayer piezoelectric actuator and ultrasonic vibrator application.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.297-299
• /
• 1999

Effects of additives on the ceramic and electrical properties of Pb(Y$_{1}$2/Ta$_{1}$2/)O$_3$-PbZrO$_3$-PbTiO$_3$ceramics in a perovskite type structure were investigated. The dielectric and piezoelectric properties of the base composition were improved markedly through selection of Fe$_2$O$_3$ additives in proper amounts. The composition Pb(Y$_{1}$2/Ta$_{1}$2/)O$_3$-PbZrO$_3$-PbTiO$_3$ obtained the dielectric constant ($\varepsilon$$_{r}$=1,425). Also, electromechanical couping factors for planar(k$_{p}$) and piezoelectric constant(d$_{33}$) were obtained 0.50 and 294[pC/N] at the additives 0wt% Fe$_2$O$_3$ respectively. The mechanical quality facor(Q$_{m}$) of Pb(Y$_{1}$2/Ta$_{1}$2/)O$_3$-PbZrO$_3$-PbTiO$_3$+Fe$_2$O$_3$(0.3 wt%) is about 510.510.510.

• Journal of the Korean Ceramic Society
• /
• v.53 no.2
• /
• pp.162-166
• /
• 2016

0.75BF-0.25BT ceramics were prepared by sintering at $980-1040^{\circ}C$ in air or under atmosphere powder. A sample with 1 mole %-excess $Bi_2O_3$ was also prepared to compensate for $Bi_2O_3$-evaporation. Physical and piezoelectric properties of these three samples were compared. When the sintering temperature increased from $980^{\circ}C$ to $1040^{\circ}C$, the density of the sample sintered in air decreased continuously due to Bi-evaporation. Due to the suppression of Bi-evaporation, the sample sintered under atmosphere powder had a higher density at sintering temperatures above $1000^{\circ}C$ than did the sample sintered in air. The addition of 1 mole %-excess $Bi_2O_3$ successfully compensated for Bi-evaporation and kept the density at the higher value until $1020^{\circ}C$. Grain size increased continuously when the sintering temperature increased from 980 to $1040^{\circ}C$, irrespective of the sintering atmosphere. When the sintering temperature increased, the piezoelectric constant ($d_{33}$) and the electromechanical coupling factor ($k_p$) increased for all samples. The sample with 1 mole % excess-$Bi_2O_3$ showed the highest density and the best piezoelectric properties at sintering temperature of $1020^{\circ}C$.