• International journal of thyroidology
• /
• v.11 no.2
• /
• pp.160-166
• /
• 2018

Background and objectives: Salivary hypofunction is one of the common side effects after radioiodine therapy, and its pathophysiology is salivary ductal stenosis resulting from ductal cell injury. This study aimed to develop the functional culture environment of human parotid gland ductal cells in in vitro three-dimensional perfusion culture system. Materials and Methods: We compared plastic dish culture method and three-dimensional culture system containing Matrigel and nanofiber. Morphogenesis of reconstituted salivary structures was assessed by histomorphometry. Functional characteristics were assessed by immunohistochemistry and reverse transcription polymerase chain reaction (aquaporin 5, CK7, CK18, connexin 43, and p21). In addition, we designed the media perfusion culture system and identified higher rate of cell proliferation and expression of connexin 43 in perfusion system comparing to dish. Results: Human parotid ductal cells were well proliferated with the ductal cell characters under environment with Matrigel. In the presence of Matrigel, aquaporin 5, CK18 and connexin 43 were more expressed than 2D dish and 3D nanofiber setting. In the media perfusion culture system, ductal cells in 3D culture media showed higher cells count and connexin 43 expression compared to 2D dish. Conclusion: This in vitro ductal cell perfusion culture system using Matrigel could be used to study for radioiodine induced sialadenitis model in vivo.

• Journal of Technologic Dentistry
• /
• v.42 no.4
• /
• pp.355-361
• /
• 2020

Purpose: In this study, we added two kinds of photoinitiators (CQ and TPO) to prepare two kinds of denture base resins (Bis-GMA series and UDMA series) for three-dimensional (3D) printing to compare and analyze their mechanical and biological properties and to find the optimal composition. Methods: Control specimens were made using the mold made of polyvinyl siloxane of the same size. Light curing was performed twice for 20 seconds on both the upper and lower surfaces with LED (light emitting diode) light-curing unit (n=10). Experimental 3D printing dental resins were prepared, to which two photoinitiators were added. Digital light processing type 3D printer (EMBER, Autodesk, CA, USA) was used for 3D printing. The specimen size was 64 mm×10 mm×3.3 mm according to ISO 20795-1. The final specimens were tested for flexural strength and flexural modulus, and MTT test was performed. Furthermore, one-way analysis of variance was performed, and the post-test was analyzed by Duncan's test at α=0.05. Results: The flexural strength of both Bis-GMA+CQ (97.12±6.47 MPa) and UDMA+TPO (97.40±3.75 MPa) was significantly higher (p<0.05) in the experimental group. The flexural modulus in the experimental group of UDMA+TPO (2.56±0.06 GPa) was the highest (p<0.05). MTT test revealed that all the experimental groups showed more than 70% cell activity. Conclusion: The composition of UDMA+TPO showed excellent results in flexural strength, flexural modulus, and biocompatibility.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.11 s.158
• /
• pp.1598-1607
• /
• 2006

The purpose of this study was to analyze the proportion of gathered skirts using a three-dimensional measurement system. And in this experiment, we have attempted to accumulate three-dimensional data of wearing model and find out adequate methods for analyzing shape of clothes. The experimental design consists of two factorial designs. We established three different kinds of fabrics, ratio of gathers. The measurement tool for three-dimensional model was whole body 3D scanner(Exima-WBS2H). Analysis program used in experiment is RapidForm 2004 PP1 and Pattern Design 2000. Data analysis utilizes SPSS WIN 10.0 Package. As the results show, there were different effect of gather and proportion of shapes among the measurements of width, thickness and areas made by different lines of vision in cross-sectional silhouette. And there were difference shapes of section area at each part of gathered skirts between vertical-outline silhouette and vortical-plane silhouette made by gathering conditions. And also the cross-sectional silhouettes and vertical silhouettes were related to shape of clothes.

• Journal of Welding and Joining
• /
• v.31 no.3
• /
• pp.11-16
• /
• 2013

Through-silicon-via (TSV) is a major technology in microelectronics for three dimensional high density packaging. The 3-dimensional TSV technology is applied to CMOS sensors, MEMS, HB-LED modules, stacked memories, power and analog, SIP and so on which can be employed to car electronics. The copper electroplating is widely used in the TSV filling process. In this paper, the various Cu filling methods using the control of the plating process were described in detail including recent studies. Via filling behavior by each method was also introduced.

• Journal of the Korean Magnetics Society
• /
• v.22 no.6
• /
• pp.195-199
• /
• 2012

Using micromagnetic simulation, we investigated the effect of thickness of a nanodisk on a resonance frequency of vortex gyration. We observed that the resonance frequency increases with increasing thickness in both cases of 2-dimensional (2D) and 3-dimensional (3D) calculation. However, there is a difference in the increasing rate of resonance frequency between 2D and 3D modeling owing to dynamically developed inhomogeneous magnetic texture along the thickness direction of disk in 3D modeling.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.839-844
• /
• 2017

In the past few years, three-dimensional (3D) printing has been developed as a rapid prototyping (RP) technique. The fused deposition modeling (FDM)-type 3D printing is one of the most useful RP methods; however, it still has several disadvantages, such as low conductivity, heat degradation, and low surface quality. In this study, test specimens are fabricated using an FDM-type 3D printer with an ABS material. Then, the specimens undergo post-processing on submerging in acetone with various processing times. As the processing time increases, surface roughness is enhanced significantly within the first five seconds by chemical processing, following which the processing effects are reduced. Furthermore, post processing causes the ultimate strength and strain to increase slightly with increased processing time.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.40 no.1
• /
• pp.32-36
• /
• 2014

Preoperative surgical simulation in orthognathic surgery has progressed in recent years; the movement of the mandible can be anticipated through three-dimensional (3D) simulation surgery before the actual procedure. In this case report, the mandible was moved to the intended postoperative occlusion through preoperative surgical 3D simulation. Right-side condylar movement change was very slight in the surgical simulation, suggesting the possibility of mandibular surgery that included only left-side ramal osteotomy. This case report describes a patient with a mild asymmetric facial profile in which the mandibular menton had been deviated to the right and the lips canted down to the left. Before surgery, three-dimensional surgical simulation was used to evaluate and confirm a position for the condyle as well as the symmetrical postoperative state of the face. Facial asymmetry was resolved with minimal surgical treatment through unilateral intraoral vertical ramus osteotomy on the left side of the mandible. It would be a valuable complement for the reduction of the surgical treatment if one could decide with good predictability when an isolated intraoral vertical ramus osteotomy can be done without a compensatory osteotomy on the contralateral side.

• Journal of dental hygiene science
• /
• v.15 no.2
• /
• pp.196-201
• /
• 2015

The purpose of this study was to evaluate marginal gap of 3 unit fixed dental prostheses (FDPs) fabricated by 3-dimensional (3D) printing technology and to compare marginal gap of its by a conventional method (lost wax technique and casting method). Ten study models were manufactured. Three unit FDPs were fabricated by 3D printing technique (3D group) and conventional methods (CV group). Marginal gaps were measured by silicone replica technique and digital microscope (${\times}160$). Mann-Whitney test was executed (${\alpha}=0.05$). The mean${\pm}$standard deviation of marginal gap for premolars and molars were $112.5{\pm}8.6{\mu}m$ and $110.2{\pm}7.0{\mu}m$ in the 3D group and $83.2{\pm}4.4{\mu}m$ and $82.2{\pm}4.6{\mu}m$ in the CV group. There were statistically significant differences (p<0.05). As results, clinical application further improvement of 3D printing technique may be required.

• The korean journal of orthodontics
• /
• v.46 no.1
• /
• pp.3-12
• /
• 2016

Objective: The purpose of this study was to compare the precision of three-dimensional (3D) images acquired using iTero$^{(R)}$(Align Technology Inc., San Jose, CA, USA) and Trios$^{(R)}$(3Shape Dental Systems, Copenhagen, Denmark) digital intraoral scanners, and to evaluate the effects of the severity of tooth irregularities and scanning sequence on precision. Methods: Dental arch models were fabricated with differing degrees of tooth irregularity and divided into 2 groups based on scanning sequence. To assess their precision, images were superimposed and an optimized superimposition algorithm was employed to measure any 3D deviation. The t-test, paired t-test, and one-way ANOVA were performed (p < 0.05) for statistical analysis. Results: The iTero$^{(R)}$ and Trios$^{(R)}$ systems showed no statistically significant difference in precision among models with differing degrees of tooth irregularity. However, there were statistically significant differences in the precision of the 2 scanners when the starting points of scanning were different. The iTero$^{(R)}$ scanner (mean deviation, $29.84{\pm}12.08{\mu}m$) proved to be less precise than the Trios$^{(R)}$ scanner ($22.17{\pm}4.47{\mu}m$). Conclusions: The precision of 3D images differed according to the degree of tooth irregularity, scanning sequence, and scanner type. However, from a clinical standpoint, both scanners were highly accurate regardless of the degree of tooth irregularity.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.39
• /
• pp.10.1-10.5
• /
• 2017

Background: Because of changing surgical procedures in the fields of oral and maxillofacial surgery, new methods for surgical education are needed and could include recent advances in digital technology. Many doctors have attempted to use digital technology as educational tools for surgical training, and movies have played an important role in these attempts. We have been using a 3D full high-definition (full-HD) camcorder to record movies of intraoral surgeries. Method: The subjects were medical students and doctors receiving surgical training who did not have actual surgical experience (n = 67). Participants watched an 8-min, 2D movie of orthognathic surgery and subsequently watched the 3D version. After watching the 3D movie, participants were asked to complete a questionnaire. Result: A lot of participants (84%) felt a 3D movie excellent or good and answered that the advantages of a 3D movie were their appearance of solidity or realism. Almost all participants (99%) answered that 3D movies were quite useful or useful for medical practice. Conclusions: Three-dimensional full-HD movies have the potential to improve the quality of medical education and clinical practice in oral and maxillofacial surgery.