• Journal of the Korean Institute of Gas
• /
• v.12 no.3
• /
• pp.13-19
• /
• 2008

Among the various prime movers for combined heat and power (CHP) system, the CNG engine is the most commonly used power generation equipment of which power is less than 1MW. The 300 kW class CNG engine for CHP can meet stringent emission regulations with the adoption of stoichiometric air-fuel ratio control and three way catalyst. As the thermal efficiency of the stoichiometric ratio engine is lower than that of lean burn engine, it is necessary to operate the stoichiometric engine at its minimum spark advance for the best torque (MBT). However, knock control should be introduced for the engine under high intake air temperature conditions because MBT operating conditions are generally very close to those of knock occurrence. In this study, engine performances and knocking characteristics were experimentally investigated for the CNG engine that needs to be operated at higher intake air temperature conditions than normal conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.2
• /
• pp.39-45
• /
• 2013

Basically, in order to apply solid propellant as ignition source to high energy metal particle combustion system, we analyzed combustion characteristics of the HTPB/AP/Al, HTPE/AP/Al propellants by using a strand burner. The propellants were tested in a high-pressure windowed strand burner, which was pressurized up to 300 psia with pure argon gas. Strand burner was visualized with two quartz windows and ignition was accomplished by a 10 W $CO_2$ laser. The burning rate of propellant was measured with high-speed camera method for frame analysis and photodiode method for combustion time analysis. Emission spectrum was measured with spectrometer at 300 nm ~ 800 nm and 1500 nm ~ 5000 nm and then we analyzed species during propellant combustion.

• Proceedings of the KIEE Conference
• /
• 2003.04a
• /
• pp.352-354
• /
• 2003

본 논문에서는 상용전력 계통이 어떠한 이유에 의하여 전력공급이 중단 되었을 때 최소의 전력공급을 위하여 독립형 시스템과 연계형 시스템을 일체화한 독립 연계형 겸용시스템의 적용 가능성을 도출하기 위하여, 설계.제작 하였다. 독립모드에서 부하는 저항부하를 사용하였으며, 300W, 600W, 900W, 1,200W의 부하시 전력품질을 측정하였으며. 1,200W의 부하시에 전압/전류 외율은 5.23% / 5.41%로 부하에 따라 변화하였으며, 연계형 시스템과 달리 전압 왜율이 부하증가에 따라 증가하는 특성을 보여 주었다.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2013.05a
• /
• pp.202-203
• /
• 2013

CIGS 단일 타켓을 DC 및 RF 마그네트론 스퍼터링을 이용하여 파워별로 Mo/SLG위에 증착하여 미세구조 및 화학조성 평가를 실시하였다. 파워가 증가함에 따라 이온의 운동에너지 증가에 따라서 결정성이 향상되었음을 확인할 수 있었다. DC 마그네트론 스퍼터링의 경우 40W에서 가장 결정성이 좋았으며, RF 마그네트론 스퍼터링은 80W에서 높은 결정성을 확인할 수 있었다. 이는 DC power 40W와 RF power 80W에서 박막의 조성이 화학양론을 만족하고 grain의 성장이 잘되었기 때문에 높은 결정성을 나타났다고 생각된다. 그리고 최적의 80W에서 기판온도를 100~400도까지 변화하여 증착해본 결과 300도에서 증착 시 가장 높은 결정성이 나타나는 것을 확인할 수 있었다. 이는 400도 이상 온도 증가 시 2차 핵생성 밀도 증가로 인해 결정성이 저하된다고 생각된다.

• Journal of electromagnetic engineering and science
• /
• v.15 no.1
• /
• pp.59-61
• /
• 2015

A wideband H-band detector operating near 300 GHz has been developed based on SiGe HBT technology. The detector consists of an on-chip antenna and a HBT differential pair for square-law detection. It showed responsivity of more than 1,700 V/W and noise equivalent power (NEP) smaller than $180pW/Hz^{0.5}$ for the measured frequency range of 250-350 GHz. The maximum responsivity and the minimum NEP were 5,155 V/W and $57pW/Hz^{0.5}$, respectively; both were obtained at 330 GHz with DC power dissipation at 9.1 W.

• Laser Solutions
• /
• v.11 no.2
• /
• pp.20-25
• /
• 2008

Polyimide is one of the useful materials in industry. The surface treatment of polyimide by a femtosecond laser can help accurate and fine fabrication of microstructure. And it can change the transmittance and reflectance of polyimide, too. We put femtosecond laser pulses on polyimide for rectangular or square type surface treaments and observe the change of transmittance and reflectance. Pulsewidth is 172 fs, laser power changes for fabrication are from 5 mW to 20 mW, and transmittance and reflectance are measured under 20m W, 300m W, and 920 mW. Pulse patterning is stable and almost no unwanted surface damage is shown. As power increases, working depth increases but working line width does not increase significantly. As speed changes, they also have same results. It shows the efficiency of a femtosecond laser is good and thermal damage is small for polyimide.

• Journal of Mushroom
• /
• v.21 no.3
• /
• pp.185-189
• /
• 2023

This study was conducted to develop a renewable and sustainable bio-material to replace polystyrene (EPS) in fungal-mycelium-based composite using agricultural by-products. Four mushrooms (Ganoderma lucidum, Fomitella fraxinea, Phellinus linteus, and Schizophyllum commune) were cultured in an oak sawdust plus rice bran substrate to select the mushroom with the best growth. The mycelia of G. lucidum showed the best growth. To investigate the optimal mixing ratio with spent mushroom substrate (SM) and oak sawdust (OS), samples were prepared by mixing SM and OS at ratios of 50%:50%, 60%:40%, and 80%:20% (w/w). Each substrate was then inoculated with G. lucidum. G. lucidum showed the best mycelial growth of 140.0 mm in the substrate with SM and OS mixed at a 60%:40% ratio. It was also found that the substrate with SM and OS mixed at a 60%:40% ratio had the best handling properties. The compressive strength of mycelial materials inoculated with G. lucidum was in the range of 300-302 kgf mm^-1, and the materials were four times stronger than polystyrene materials. These results indicate that substrates comprising spent mushroom substrate mixed with oak sawdust can be successfully upcycled to mycelium-based composite materials using G. lucidum. This represents a sustainable approach.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.08a
• /
• pp.154-155
• /
• 2001

A laser system for therapy of cancer is proposed in this paper. In order to accuracy and statistical output control we used the constant current control method and designed the power source to protect the resonator from the over -current, rush-current and electrical fault. The most important things are the radiation type for cancer therapy in laser system, we developed the radiation type of cw, pulse, and burst pulse. The experimental result show that laser beam power increase linearly from 100mW to 300mW for input current increasing and the exposure time.

• Journal of the Korean Solar Energy Society
• /
• v.25 no.1
• /
• pp.27-34
• /
• 2005

This study aims to evaluate application of a heat recovery ventilator(HRV) using photovoltaic(PV) system. To this end, we analyzed performance of a PV system, which it was evaluated by monthly power wattage and conversion efficiency according to design capacity of a HRV. The results of this study can be summarized as follows. (1) A conversion efficiency of the PCS was evaluated about 86% in rated power. (2) A maximum, minimum and average output power were respectively analyzed 49.2W, 47.3W, and 48.8W. (3) Total power wattage of 200W PV system was 211kW and it was 316kW in case of 300W PV system. (4) Insufficient electrical power of a duct and window type ventilation system was respectively calculated 133.5kW and 147.7kW.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.5
• /
• pp.200-207
• /
• 2020

MoSi₂, (Mo_1/2W_1/2)Si₂, and WSi₂ powders were synthesized by self-propagating high-temperature synthesis (SHS) method. The synthesized powders were heat-treated at 500, 1,000, 1,200, 1,300, 1,400, 1,500 and 1,600℃ in ambient atmosphere. Oxidation of Mo-W silicide powder was found at low temperature of 500℃. XRD structure analysis and DTA/TG data showed that MoO₃ was formed with 500℃ heat treatment for 1 hour, and that it was α-cristobalite phase that was formed with 1200℃ heat treatment, not α-quartz phase which is commonly found and stable at room temperature. Existence of W accelerated decomposition at both low and high temperature. Fully sintered MoSi₂ and (Mo_1/2W_1/2)Si₂ specimen did not show decomposition or weight loss by oxidation, with 1 hour heat treatment at either low or high temperature. Notably, it was difficult to sinter WSi₂ because of oxidation reaction at low temperature.