• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.218-220
• /
• 2004

A new wide-band VCO topology using Miller capacitance is proposed. Contrary to conventional VCO using the Miller capacitance where the variable amplifier gain is negative, the proposed VCO uses both the negative and positive variable amplifier gain to enhance the frequency tuning range significantly. The proposed VCO is simulated using HSPICE. The simulations show that 410MHz and 220MHz frequency tuning range are obtained using the negative .and positive variable amplifier gain, respectively. The tuning range of the proposed VCO is $23\%$ of the center frequency(2.8GHz). The phase noise is -104dBc/Hz at 1MHz offset by simple model. The operating current is only 3.84mA at 2.5V power supply.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.523-526
• /
• 2002

This paper presents the simulation of Au / $Ba_{x}$S $r_{1-x}$ Ti $O_3$(BSTO) / Magnesium oxide (MgO) multi-layered and electrically tunable band-pass filters (BPFs) by using high frequency structure simulator (HFSS). This model is a two-pole microstrip edge coupled filter. The filter was designed fur a center frequency about 5.8 GHz. The tunabillity of the filter is achieved using the nonlinear dc electric-field dependence on the relative dielectric constant of BSTO frroelectric thin film. This work seems very promising for future wireless communication systems....

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.181-182
• /
• 2007

Wireless home theater and speaker system was designed. That has 20W output per channel, 0.1% THD (Total Harmonic Distortion) and automatic algorithm avoiding noise. The 3D stereophonic sound was realized through the wireless 5.1channel speaker system designed. That could be secured 0.4% improvement effect of THD compared with wire speaker systems. Specially in transfer sound with wireless, Frequency Hopping Spread Spectrum was superior than Direct Sequence Spread Spectrum in household electric appliances and wireless internet environment that radiated noise similar with ISM Band using 2.4GHz.

• Journal of information and communication convergence engineering
• /
• v.16 no.4
• /
• pp.203-212
• /
• 2018

In this article, a novel design of patch antenna with wide band characteristics is presented. The proposed antenna is having electrical dimensions of $0.14{\lambda}{\times}0.11{\lambda}$ (at lower initial frequency) and footprints of $150mm^2$. Structural parameters optimization shows 3.1-23.5 GHz frequency range for a (reflection coefficient) $S_{11}{\leq}-10dB$ and simulated gain 6.8 dB is obtained. An equivalent circuit model is proposed to get an insight view of antenna. Advanced Systems Design (ADS) simulation results are obtain which confirm the validity of proposed model. Degenerated foster canonical form has been used to explain the reactance and capacitive behavior idea of simulated proposed antenna's input impedance later on an equivalent circuit model and smith chart is also suggested. HFSS and CST have been used to analyze antenna behavior. The proposed antenna can be further used for microwave image detection applications.

• Korean Journal of Optics and Photonics
• /
• v.16 no.5
• /
• pp.469-475
• /
• 2005

An integrated photonic microwave bandpass filter has been proposed and demonstrated incorporating a coherently coupled microring resonator in low-loss polymers. The proposed device may feature compact site, simple structure, tuning via the thermooptic and electrooptic effect, and flexible integration with other electrical and optical devices. The resonator was designed to have an extremely small bandwidth so that it could be used to selectively pass the optical signal carrying the microwave signal to attain efficient bandpass filtering. We made and tested two resonators with a single ring and double rings, and performed a theoretical fitting of their measured transfer curves to predict the performance of the microwave filters based on them precisely. It was found that as the number of the rings used for the resonator increases, the bandwidth gets smaller, the rolloff sharper, and the band rejection higher. Finally our filter exhibited the center frequency of 10GHz, the 3-dB bandwidth of 1.0GHz, the corresponding quality (Q) factor of 10, and the rejection outside of the passband of more than 25dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1034-1046
• /
• 2011

In this paper, a design and fabrication of 40 W power amplifier for the X-band using load-pull measurement of GaN HEMT chip are presented. The adopted active device for power amplifier is GaN HEMT chip of TriQuint company, which is recently released. Pre-matched fixtures are designed in test jig, because the impedance range of load-pull tuner is limited at measuring frequency. Essentially required 2-port S-parameters of the fixtures for extraction optimal input and output impedances is obtained by the presented newly method. The method is verified in comparison of the extracted optimal impedances with data sheet. The impedance matching circuit for power amplifier is designed based on EM co-simulation using the optimal impedances. The fabricated power amplifier with 15${\times}$17.8 $mm^2$ shows the efficiency above 35 %, the power gain of 8.7~8.3 dB and the output power of 46.7~46.3 dBm at 9~9.5 GHz with pulsed-driving width of 10 usec and duty of 10 %.

• Journal of electromagnetic engineering and science
• /
• v.2 no.1
• /
• pp.50-55
• /
• 2002

In this paper, Ive propose a bow-tie-shaped meander slot antenna find by a microstrip line to achieve compact size as well as wideband characteristic. While conventional bow-tie slot antennas exhibit wide band characteristic, they have relatively large size. On the other hand, the meander slot antennas are very small, but they reveal quite narrow bandwidth (typically less than 1 %). To realize miniaturized antennas balling large bandwidth, combination of the bow-tie slot and the meander slot geometries is proposed in this paper. Theoretical results show that the proposed antenna with uniform slot width is 65.5 % smaller than that of the conventional bow-tie antenna in size, while the bandwidth is 3 times larger than that of the meander slot antenna. Moreover, the non-uniform slot width antenna shows 60 % smaller in size and about 3.5 times wider in bandwidth than the previous antennas. Measured antenna performance reveals excellent agreement with the predicted values.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.5 s.335
• /
• pp.55-60
• /
• 2005

A V-band MIMIC quadruple subharmonic mixer is reported in this paper. The cascode harmonic generator is proposed for a high conversion gain. The proposed cascode harmonic generator is shown with a 4-th harmonic output characteristic that represents an average of 2.9 dB and a maximum of 4 dB higher than the conventional multiplier. The measured result of the subharmonic mixer has a conversion gain of 3_4 dB which a good conversion gain at a LO power of 13 dBm. Isolations of LO-to-IF and LO-to-RF were obtained -53.6 dB and -46.2 dB, respectively. The conversion gain of the subharmonic mixer in this study has a higher conversion gain compared with some other reports in millimeter-wave range.

• Journal of electromagnetic engineering and science
• /
• v.10 no.4
• /
• pp.316-321
• /
• 2010

This paper presents a novel fourth harmonic mixer with new structure. The traditional 3-ports fourth harmonic mixer and the novel fourth harmonic mixer are designed by ADS, HFSS and CST simulator. The mixers have been fabricated and tested. The size of the traditional 3-ports fourth harmonic mixer is $12{\times}15$ mm, and the best conversion loss is 18.7 dB according to the measurement. Since the traditional 3-port mixer size is too large to be ranked, we design a novel fourth harmonic mixer for imaging system. The width of the mixing module in the novel fourth harmonic mixer is only 3.65 mm, and this size is fully capable to meet the mixer unit space which is not greater than 5 mm. The simulation result shows that the mixer has good performance, and the experiment result shows that the best conversion loss of the novel fourth harmonic mixer is 16.3 dB at RF signal of 91.3 GHz.

• Nuclear Engineering and Technology
• /
• v.38 no.8
• /
• pp.785-792
• /
• 2006

The microwave heating system of KSTAR consists of ECH and LHCD. ECH and LHCD offer the benefits ofa reliable operation at the start of plasma formation and a non-inductive current drive durable steady state operation, respectively. LHCD uses a C-band microwave system with a frequency of 5 GHz. A pulsed power modulator with a power of 3.6 MW, $4{\mu}S$, 200 pps is required to drive the high-powered magnetron. The development of a pulse modulator with 1:4 pulse transformers is the focus of the research in this study. The peak power handling capability is 3.6 MW (45 kV, 90 A at load side with a pulse width of $4{\mu}S$). This paper describes the system overview and test results of the pulsed modulator. In particular, a simulated waveform is compared with the tested waveform.