• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 추계학술대회 논문집
• /
• pp.75-76
• /
• 2008

In this study, texture development and bending characteristics of strong {0002} textured were observed. AZ31 Mg alloy sheets were prepared along the angle of 0 and 12.5 degrees to the lolling direction or {0002} texture. Prepared samples with different angles to the rolling direction were rolled at room temperature condition and after subsequent heat treatment to investigate texture with x-ray diffractometer, respectively The specimen having along the angles of 0 degree to rolling direction shows the highest load and 12.5 degrees specimen shows the highest displacement among any other specimens in bending test.

• 한국공간구조학회논문집
• /
• 제19권3호
• /
• pp.77-83
• /
• 2019

AU(A plus U-shaped) composite beam was developed for reducing the story height in the residential buildings, and saving the cosrtuction cost of floor structures. Structural performance and economic feasibility of the composite beam have been sufficiently approved through the structural experiments and the analytical studies. Fire safety for the practical application of the composite beam has also been verified through the fire resistance tests and the heat transfer analyses. In this study 2-points bending tests were performed on the four specimens already tested for fire resistance to evaluate the residual bending strength of AU composite beam after fire accident. The same bending test was performed on the one fresh specimen having the same section and span of the specimens for practically comparative study.

• 한국정밀공학회지
• /
• 제22권9호
• /
• pp.162-172
• /
• 2005

The objective of this research works is to investigate into characteristics of bending stiffness and failure for the ISB ultra-lightweight panel with internally structured material. The expanded metal with a crimped pyramid shape and woven metal are employed as an internally structured material. Through three-points bending test, the force-displacement curve and failure shape are obtained to examine the deformation pattern, characteristic data, such as maximum load, displacement at maximum load, etc, and failure pattern of the ISB panel. In addition, the influence of design parameters fur ISB panel on the specific stiffness, the specific stiffness per unit width, failure mode and failure map has been found. Finally, it has been shown that ISB containing expand metal with the crimped pyramidal shape is prefer to that containing woven metal from the view point of optimal design for ISB panel.

• Journal of the Korean Wood Science and Technology
• /
• 제26권4호
• /
• pp.6-12
• /
• 1998

Test results of domestic softwood lumber were presented to examine the notch effect of beams and compare to present AIJ(Architecture Institute of Japan) formula in notched wood member especially positioned in bottom side (tension side) of a beam. Notched lumber was tested under following condition : each specimen supported simply, and subjected to third-point loading at points of 1/3 of the span length. Notch was located opposite side to loading direction and notch depth were 1/6, 1/4, 1/3 of beam depth. Deflection and load were measured by digital dial guage each in 25kgf increment. Bending test results were as follows; Mpro/Mmax range (proportional and maxium bending moment ratio in notched beam) was 0.5 - 0.65. It was considered that maxium bending moment was about 1.5 times to proportional bending moment in notched beam and showed same tendency in the test result of ordinary wood specimens. AU standard formula for the tension side notch, Mmat = 0.6 ${\times}$ (Zo $\sigma$), the constant 0.6 was suitble for notch ratio(notch depth to beam depth) 1/6, but this ratio for 1/4, and 1/3 was not. So it is preferable to accept smaller value than 0.6 for notch ratio more than 1/3. These experiment results showed critical effect in tension side notched wood beam especially in greater than notch ratio 1.3 of wood beam. From the above results, it is recommened to revise design formula adoptable to domestic wood constructon member with tension side notched member.

• 마이크로전자및패키징학회지
• /
• 제18권3호
• /
• pp.45-52
• /
• 2011

Flip Chip Ball Grid Array (FCBGA) 패키지의 솔더조인트 신뢰성을 평가하기 위한 방법으로는 다이 충격법, 다이 전단법, 3점 굽힘법, 열충격법 등이 활용된다. 본 연구에서는 솔더 접합부의 주요 고장메카니즘인 취성파괴를 확인하기 위한 방법으로 리플로우 상태, $85^{\circ}C$/85%RH 처리, $150^{\circ}C$/10hr 에이징의 처리한 후, 4가지 평가법으로 평가를 진행하여 파단모드를 분석하였다. 본 연구결과에서는 다이 충격법과 다이 전단법의 Good joint rate (GJR, %)는 리플로우 상태와 $85^{\circ}C$/85%RH처리에서 각각 89~91%와 100% 였으며, $150^{\circ}C$/10hr 에이징에서는 66%와 90%를 나타내었다. 3점 굽힘법과 열충격법의 GJR(%)는 3종류 샘플에서 모두 100%를 나타내어 변별력이 없었다. C4 솔더접합부의 신뢰성 평가법에 따른 GJR(%)의 변별력을 확인할 수 있는 방법은 die shock 과 die shear test였다.

• 대한금속재료학회지
• /
• 제46권2호
• /
• pp.80-87
• /
• 2008

Many researches related to the reliability of Pb-free solder joints with PCB (printed circuit board) surface finish under thermal or vibration stresses are in progress, because the electronics is operating in hash environment. Therefore, it is necessary to assess Pb-free solder joints life with PCB surface finish under thermal and mechanical stresses. We have investigated 4-points bending fatigue lifetime of Pb-free solder joints with OSP (organic solderability preservative) and ENIG (electroless nickel and immersion gold) surface finish. To predict the bending fatigue life of Sn-3.0Ag-0.5Cu solder joints, we use the test coupons mounted 192 BGA (ball grid array) package to be added the thermal stress by conducting thermal shock test, 500, 1,000, 1,500 and 2,000 cycles, respectively. An 4-point bending test is performed in force controlling mode. It is considered that as a failure when the resistance of daisy-chain circuit of test coupons reaches more than $1,000{\Omega}$. Finally, we obtained the solder joints fatigue life with OSP and ENIG surface finish using by Weibull probability distribution.

• Structural Engineering and Mechanics
• /
• 제68권4호
• /
• pp.497-505
• /
• 2018

Three points bending flexural test was modeled numerically to study the crack propagation in the pre-cracked beams. The pre-existing edge cracks in the beam models were considered to investigate the crack propagation and coalescence paths within the modeled samples. The effects of particle size on the single edge-notched round bar in bending test were considered too. The results show that Failure pattern is constant by increasing the ball diameter. Tensile cracks are dominant mode of failure. These crack initiates from notch tip, propagate parallel to loading axis and coalescence with upper model boundary. Number of cracks increase by decreasing the ball diameter. Also, tensile fracture toughness was decreased with increasing the particle size. In the present study, the influences of particles sizes on the cracks propagations and coalescences in the brittle materials such as rocks and concretes are numerically analyzed by using a three dimensional particle flow code (PFC3D). These analyses improve the understanding of the stability of rocks and concretes structures such as rock slopes, tunnel constructions and underground openings.

• 토지주택연구
• /
• 제12권4호
• /
• pp.119-125
• /
• 2021

본 연구에서는 그리드를 이용한 철근콘크리트 휨부재의 연성보강 효과를 실험결과로 제시했다. 실험변수로는 비보강 철근콘크리트 휨부재(ORI), 바닥면 보강 철근콘크리트 휨부재(REB), 바닥 및 측면 보강 철근콘크리트 휨부재(REBS)가 있다. 실험은 4절점 휨 실험으로 수행되었다. 실험 결과, 보강을 통해 최대 휨강도가 17~20% 증가하였고, 측면 보강을 통해 휨 파괴 유도를 통한 연성보강 효과를 확인하였다. 또한, 연성지수를 계산하여 REB와 REBS의 연성지수가 ORI 대비 각각 2배, 3배 증가하였음을 확인하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 춘계학술대회 논문집
• /
• pp.167-168
• /
• 2009

• 한국해안해양공학회지
• /
• 제18권3호
• /
• pp.225-240
• /
• 2006

판에 작용하는 등분포하중과 등변분포하중에 의한 휨 모멘트를 계산하기 위해 무차원 방정식에 대한 유한 차분법으로 제시하고 변장비와 격자수에 따른 수치해의 수렴을 분석하였다. 유한 차분법의 수치해는 격자점을 최대 11,520개까지 사용하여 해를 구하였고 변장비에 따른 최적 격자수를 제시하였다. 본 수치해는 Levy형 해석 해와 달리 자유단의 모멘트 경계조건을 만족하며 자유단과 고정단의 교점부근에서는 특이한 모멘트 분포를 보인다. 등분포하중과 등변분포하중에 의한 Levy형 해석해의 무차원 휨 모멘트 값과 본 결과를 비교하였으며 특이한 분포를 보이는 자유단과 그 부근을 제외하면 두 값은 동일한 것으로 나타났다.