• 디지털융복합연구
• /
• 제13권1호
• /
• pp.331-339
• /
• 2015

사이버나이프치료에서 삽입된 금표지자의 삽입 개수 및 인식의 제한으로 인하여 3D DOF로 치료하는 경우 척추구조물 정렬을 가능하게 하는 Xsight spine tracking system으로 회전방향의 위치오차를 보정함으로서 표적위치오차를 개선하고, 치료방법의 대안을 제시하고자 한다. 실험결과 6D DOF에서 표적위치오차는 $0.214{\pm}0.058mm$, 종양내부에 삽입된 2개 금표지자를 이용한 3D DOF에서 $0.673{\pm}0.142mm$, 종양외부에 삽입된 2개 금표지자를 이용한 3D DOF에서 $1.126{\pm}0.253mm$, Xsight spine tracking system의 적용 한 3D DOF에서 $0.542{\pm}0.103mm$로 나타났다. 실험결과 척추 구조물로 회전방향에 대한 보정을 시행하였을 때 표적위치에 대한 정확성이 약 48% 향상되었다. 또한, 선량분포의 일치성도 약 3%가 향상되어 일치하는 것을 확인할 수 있었다. 따라서 척추구조물 정렬을 병용한 Xsight spine tracking system의 회전방향에 대한 보정은 유용한 것으로 평가 되었다.

• 전기학회논문지
• /
• 제57권8호
• /
• pp.1362-1370
• /
• 2008

This paper describes the design and characteristic analysis of a novel 3-DOF(Degree of Freedom) spherical motor. For multi DOF actuating, several numbers of motors have been used. By the using of normal motors they connected each other in single joint, is necessary to a several type of complex power transmission devices. The 3-DOF spherical motor can drive roll, pitch, and yaw motion in only one unit and it is not necessary to use additional gears and links parts. Therefore the using of 3-DOF spherical motor can eliminate; combined effects of inertia, backlash, non-linear friction, and elastic deformation of gears. In this paper, we propose the novel structured 3-DOF spherical motor and derive its principles of operation. Firstly, we designed concept model of novel structured 3-DOF spherical motor. Next, we derive the control method by calculating the currents. Also, to have intuitive driving control, we express the rotor position in equivalent angle-axis system and determine the exciting period of currents from the calculation result of the currents. To verify the control method, we calculated the currents by the position of rotor. and then we analyzed the characteristics by 3D Finite Element Method when the calculated currents are excited.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.302-307
• /
• 2005

Recently, lots of parallel mechanisms for spatial 3-DOF and 6-DOF were investigated. However, research on 4-DOF and 5-DOF parallel mechanisms has been very few. In this paper, we propose a 4-DOF parallel mechanism that consists of 3-rotational and 1-translational motions. The kinematic characteristics of this mechanism are analyzed in terms of an isotropic index and maximum force transmission ratio, and its kinematic optimization is being conducted to ensure enhanced kinematic performances

• 상하수도학회지
• /
• 제18권2호
• /
• pp.215-221
• /
• 2004

Effluent of wastewater treatment plant is to be disinfected to protect drinking water sources. DOF (Dissolved Ozone Flotation) was developed to meet this purpose. DOF was developed by combining DAF system with ozone. DAF system has good floating power with numerous microbubbles, and ozone has strong oxidation capability. And DOF system has good floating power and strong oxidation capability simultaneously. When DOF was applied to secondary wastewater effluent, color of 11CU in raw water which was secondary effluent was reduced to 1CU by the DOF system. Removal rate of other water quality parameters treated by DOF were also higher than that by DAF, which were proved the strength of oxidation capability of ozone. When ozone concentration of 3.3mg/l were applied in DOF system, general aerobic bacteria were reduced to 5CFU/ml from TNTC (Too many Numbers To Count). With the same ozone concentration, total coliform were not detected at all. These figures are under the numbers of drinking water regulation. These microbes were the target parameters of DOF. It was proved that DOF was very effective in disinfection of wastewater treatment plant effluent as well as in removal of color, turbidity, and T-P.

• 한국정밀공학회지
• /
• 제27권4호
• /
• pp.53-62
• /
• 2010

This study introduces about development of multi-DOF ultrasonic motor that are composed of a bar-shaped stator and a spherical rotor. The ultrasonic motor is a motor which is operated by vibrations over frequency of 20kHz. The multi-DOF ultrasonic motor will be developed by expanding the basic theory of existing 1-DOF ultrasonic motor. It can generate 3-DOF rotation of the rotor around perpendicular axes using 3 vibration modes of stator. By using finite element methods, the optimal dimension of stator is decided and made the components of stator. When we apply the multi-DOF ultrasonic motor composed of rotor and stator to the driving test system, it will be checked whether the motor can be driven at the direction of 3-DOF or not. And it is proposed how the simulation of square bar shaped multi-DOF ultrasonic motor is accomplished.

• 한국기계가공학회지
• /
• 제21권2호
• /
• pp.116-122
• /
• 2022

This study proposed a method of testing the stability when selecting gears to reduce the weight of a 3-DOF wrist mechanism for a pick-and-place 3-DOF parallel robot with an increased workspace by using an additional straight axis at its top. We performed SolidWorks^® modeling- and ANSYS^®-based structural analysis of a pinion gear, which is most vulnerable to the force from a 3-DOF wrist mechanism, to lighten the robot weight for performing various tasks. When the initial analysis results considerably differed from the theoretical values calculated in advance, we checked and identified the errors in the contact conditions or input values. Ultimately, it is believed that the methodology presented in this paper will help in mitigating errors during analysis and determine the accurate values for a lightweight 3-DOF wrist mechanism for a parallel robot with an expanded workspace.

• 한국정밀공학회지
• /
• 제26권8호
• /
• pp.79-88
• /
• 2009

This paper presents the analytical stiffness analysis method for a low-DOF planar parallel manipulator. An n-DOF (n<3) planar parallel manipulator to which 1- or 2-DOF serial mechanism is connected in series may be used as a positioning device in planar tasks requring high payload and high speed. Differently from a 3-DOF planar parallel manipulator, an n-DOF planar parallel counterpart may be subject to constraint forces as well as actuation forces. Using the theory of reciprocal screws, the planar stiffness is modeled such that the moving platform is supported by three springs related to the reciprocal screws of actuations (n) and constraints (3-n). Then, the spring constants can be precisely determined by modeling the compliances of joints and links in serial chains. Finally, the stiffness of two kinds of 2-DOF planar parallel manipulators with simple and complex springs is analyzed. In order to show the effectiveness of the suggested method, the results of analytical stiffness analysis are compared to those of numerical stiffness analysis by using ADAMS.

• 한국항공운항학회지
• /
• 제24권1호
• /
• pp.1-9
• /
• 2016

In this paper, we integrate three degree of freedom(3DOF) point-mass model for aircraft and three-dimensional path generation algorithms using dubins curve and nonlinear path tracking law. Through this integration, we apply the path generation algorithm to the path planning, and verify tracking performance and feasibility of using the aircraft 3DOF point-mass model for air traffic management. The accuracy of modeling 6DOF aircraft is more accurate than that of 3DOF model, but the complexity of the calculation would be raised, in turn the rate of computation is more likely to be slow due to the increase of degree of freedom. These obstacles make the 6DOF model difficult to be applied to simulation requiring real-time path planning. Therefore, the 3DOF point-mass model is also sufficient for simulation, and real-time path planning is possible because complexity can be reduced, compared to those of the 6DOF. Dubins curve used for generating the optimal path has advantage of being directly available to apply path planning. However, we use the algorithm which extends 2D path to 3D path since dubins curve handles the two dimensional path problems. Control law for the path tracking uses the nonlinear path tracking laws. Then we present these concomitant simulation results.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.64.3-64
• /
• 2002

$\textbullet$ Introduction to 3-Dimensional Nanorobotic Manipulation System $\textbullet$ Concept Design and Operating Principle $\textbullet$ Analytic Model for target System $\textbullet$ Fabrication and Experimental Setup of 3-DOF Mobile Microrobot $\textbullet$ Experimental Works or 3-DOF Mobile Microrobot

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.50-50
• /
• 2000

In this paper, a new measuring system is :proposed which can measure the fine 6-DOF displacement of rigid bodies. Its measurement principle is based on detection of laser beam reflected from a specially fabricated mirror that looks like a triangular pyramid having an equilateral cross-sectional shape. The mirror has three lateral reflective surfaces inclined 45$^{\circ}$ to its bottom surface. We call this mirror 3-facet mirror. The 3-facet mirror is mounted on the object whose 6-DOF displacement is to be measured. The measurement is operated by a laser-based optical system composed of a 3-facet mirror, a laser source, three position-sensitive detectors(PSD). In the sensor system, three PSDs are located at three corner points of a triangular formation, which is an equilateral triangular formation tying parallel to the reference plane. The sensitive areas of three PSDs are oriented toward the center point of the triangular formation. The object whose 6-DOF displacement is to be measured is situated at the center with the 3-facet mirror on its top surface. A laser beam is emitted from the laser source located at the upright position and vertically incident on the top of the 3-fatcet mirror. Since each reflective facet faces toward each PSD, the laser beam is reflected at the 3-facet mirror and splits into three sub-beams, each of which is reflected from the three facets and finally arrives at three PSDs, respectively. Since each PSD is a 2-dimensional sensor, we can acquire the information on the 6-DOF displacement of the 3-facet mirror. From this principle, we can get 6-DOF displacement of any object simply by mounting the 3-facet mirror on the object. In this paper, we model the relationship between the 6-DOF displacement of the object and the outputs of three PSDs. And, a series of simulations are performed to demonstrate the effectiveness of the proposed method. The simulation results show that the proposed sensing system can be an effective means of obtaining 3-dimensional position and orientation of arbitrary objects.