• Journal of Korean Society of Steel Construction
• /
• v.16 no.4 s.71
• /
• pp.407-414
• /
• 2004

Bridges in common use are expected to have more varieties of load in their connected members and bolts than in construction. Faults in connection members or bolts occur so often according to the time flow. One of the purposes of this study is to find out the behavior and structural features of high-tension bolted joints with faults that are very difficult and cost much to find out through experimentation with finite element analysis. Another purpose of this study is to provide sufficient data, estimated experimental results, and the scheme of the test plate for an economical experimental study in the future. Surveys of bridges with a variety of faults and statistical classifications of their faults were performed, as was a finite element analysis of the internal stress and the sliding behavior of standard and defective bridge models. The finite element analysis of the internal stress was performed according to the interval of the bolt, the thickness of the plate, the distance of the edge, the diameter of the bolt, and the expansion of the construction. Furthermore, the analysis explained the sliding behavior of high-tension bolt joints and showed the geometric non-linear against the large deformation, and the boundary non-linear against the non-linear in the contact surface, including the material non-linear, to best explain the exceeding of the yield stress by sliding. A normally bolted high-tension bolt joint and deduction of bolt tension were also analyzed with the finite element analysis of bridge-sliding behavior.

• Journal of the Korean Vacuum Society
• /
• v.20 no.5
• /
• pp.327-332
• /
• 2011

Plasma polymerized styrene (ppS) thin films were prepared on ITO coated glass substrates for a MIM (metal-insulator-metal) structure with thermally evaporated Au thin film as metal contact. Also the ppS thin films were applied as organic insulator to a MIS (metal-insulatorsemiconductor) device with thermally evaporated pentacene thin film as organic semiconductor layer. After the I-V and C-V measurements with MIM and MIS structures, the ppS revealed relatively higher dielectric constant of k=3.7 than those of the conventional poly styrene and very low leakage current density of $1{\times}10^{-8}Acm^{-2}$ at electric field strength of $1MVcm^{-1}$. The MIS structure with the ppS dielectric layer showed negligible hysteresis in C-V characteristics. It would be therefore expected that the proposed ppS could be applied as a promising dielectric/insulator to organic thin film transistors, organic memory devices, and flexible organic electronic devices.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.685-691
• /
• 2020

In this study, an algorithm that recognizes numbers from 0 to 9 was developed using the data obtained after tracking hand movements using the echo signal of a millimeter-wave radar sensor at 77 GHz. The echo signals obtained from the radar sensor by detecting the motion of a hand gesture revealed a cluster of irregular dots due to the difference in scattering cross-sectional area. A valid center point was obtained from them by applying a K-Means algorithm using 3D coordinate values. In addition, the obtained center points were connected to produce a numeric image. The recognition rate was compared by inputting the obtained image and an image similar to human handwriting by applying the smoothing technique to a CNN (Convolutional Neural Network) model trained with MNIST (Modified National Institute of Standards and Technology database). The experiment was conducted in two ways. First, in the recognition experiments using images with and without smoothing, average recognition rates of 77.0% and 81.0% were obtained, respectively. In the experiment of the CNN model with augmentation of learning data, a recognition rate of 97.5% and 99.0% on average was obtained in the recognition experiment using the image with and without smoothing technique, respectively. This study can be applied to various non-contact recognition technologies using radar sensors.

• Tribology and Lubricants
• /
• v.36 no.2
• /
• pp.105-115
• /
• 2020

This paper presents a numerical study on the rotordynamic analysis of a dual-spool turbofan engine in the context of blade defect events. The blades of an axial-type aeroengine are typically well aligned during the compressor and turbine stages. However, they are sometimes exposed to damage, partially or entirely, for several operational reasons, such as cracks due to foreign objects, burns from the combustion gas, and corrosion due to oxygen in the air. Herein, we designed a dual-spool rotor using the commercial 3D modeling software CATIA to simulate blade defects in the turbofan engine. We utilized the rotordynamic parameters to create two finite element Euler-Bernoulli beam models connected by means of an inter-rotor bearing. We then applied the unbalanced forces induced by the mass eccentricities of the blades to the following selected scenarios: 1) fully balanced, 2) crack in the low-pressure compressor (LPC) and high pressure compressor (HPC), 3) burn on the high-pressure turbine (HPT) and low pressure compressor, 4) corrosion of the LPC, and 5) corrosion of the HPC. Additionally, we obtained the transient and steady-state responses of the overall rotor nodes using the Runge-Kutta numerical integration method, and employed model reduction techniques such as component mode synthesis to enhance the computational efficiency of the process. The simulation results indicate that the high-vibration status of the rotor commences beyond 10,000 rpm, which is identified as the first critical speed of the lower speed rotor. Moreover, we monitored the unbalanced stages near the inter-rotor bearing, which prominently influences the overall rotordynamic status, and the corrosion of the HPC to prevent further instability. The high-speed range operation (>13,000 rpm) coupled with HPC/HPT blade defects possibly presents a rotor-case contact problem that can lead to catastrophic failure.

• Korean journal of applied entomology
• /
• v.59 no.1
• /
• pp.55-64
• /
• 2020

Smart greenhouses are primarily used for growing fruits and vegetables, such as sweet peppers, tomatoes, strawberries. Although the number of smart greenhouses has been increasing exponentially, no studies have been performed to evaluate the state of smart greenhouses in Korea. Therefore, this study was conducted to determine current state of smart greenhouses with regard to greenhouse specifications, crop growing methods, pests, and user satisfaction in Korea. Contact information for smart greenhouses was provided by the officials of local agricultural research and extension services. This survey was conducted by visiting each greenhouse. Results showed that approximately 50% of surveyed smart greenhouses were between 3,300 ㎡ and 6,600 ㎡. The most frequently chosen method for pest control was chemical pesticides (97.1%). Powdery mildew and gray mold comprised 54.4% and 33.8% of the crop diseases, respectively. All tomato greenhouse farmers considered whiteflies the most problematic pest. In contrast, 76.5% and 70.6% of sweet pepper farmers believed thrips and aphids posed significant threats, respectively. The mean satisfaction score was 7.5 out of 10 points, with 10 being "extremely satisfied". These results will aid in decision making with respect to the management of current smart greenhouses and the design of future smart farms in Korea.

• Journal of the Korean Electrochemical Society
• /
• v.10 no.2
• /
• pp.145-149
• /
• 2007

Electrochemical studies were performed for a single particle of nickel hydroxide for the cathode of Ni-MH batteries. A carbon fiber microelectrode was manipulated to make electrical contact with an alloy particle, and electrochemical experiments were performed. As a result of cyclic voltammetry, the oxidation/reduction and oxygen evolution reaction (OER) are clearly separated for a single particle. The total cathodic charge (Qred) is practically constant for the scan rate investigated, indicating that the whole particle has reacted. The total anodic charge(Qox) was larger than that of reduction reaction, and the magnitude of oxygen evolution taking place as a side reaction was enhanced at lower scan rates. As a result of galvanostatic charge and discharge measurement, the discharge capacity of single particle was found to be 250 mAh/g, value being very close to the theoretical capacity (289 mAh/g). The apparent proton diffusion coefficient(Dapp) using potential step method inside the nickel hydroxide was found to range within $3{\sim}4{\times}10^{-9}\;cm^2/s$.

• Journal of Korean Society of Steel Construction
• /
• v.16 no.5 s.72
• /
• pp.609-619
• /
• 2004

An investigation was conducted on the activities around Europe in order to solve the problem of the thermal bridging of steel studs, which had caused a significant disadvantage. This study included the following: diminishing the contact area between the studs and the sheathing, lengthening the heat transfer route, replacing the steel web with a less conductive material, and placing foam insulation in locations where the thermal shorts are most critical. Although energy efficiency is usually the focus of such foreign cases because their stud application is mostly limited to low-rise residential buildings, both structural and thermal performance are taken into consideration in this study because these target middle-story buildings. A hybrid stud composed of steel and polymer was also developed. This hybrid stud, which is 150 SL in size, is made of a galvanized steel sheet (SGC58) and a glass fiber reinforced polymer (GFRP) withepoxy bonding. A total of 32 specimens were manufactured. Its parameters comprise two types of connection detail,s: the thickness of steel (1.0mm and 1.2mm) and of the GFRP (4mm-4ply and 6mm-6ply), and the ratio of the length to the depth (L/D = 3, 6, 9, 12). Steel stud specimens with the same conditions were compared to the hybrid stud. The test revealed that in the case of the steel specimen with a thickness of 1.0mm, the maximum load of hybrid studs increased an average of 1.62 times comparedto that of the steel stud. In the case of the steel specimen with a thickness of 1.2mm, on the other hand, the average increase was 1.46times. All specimens showed full composite action until the collapse.

• Journal of Biomedical Engineering Research
• /
• v.25 no.5
• /
• pp.361-367
• /
• 2004

The axial compressive strength, relative 3-D stability and osteoconductive shape design of an intervertebral fusion cage are important biomechanical factors for successful intervertebral fusion. Changes in the stress distribution of the vertebral end plate and in cage stability due to changes in the spike shape of a newly contrived box-shaped fusion cage are investigated. In this investigation, the initial contact of the cage's spikes with the end plate and the penetration of the cage's spikes into the end plate are considered. The finite element analysis is conducted to study the effects of the cage's spike height, tip width and angle on the stress distribution of the vertebral end plate, and the micromigration of the cage in the A-P direction. The stress distribution in the end plate is examined when a normal load of 1700N is applied to the vertebra after inserting 2 cages. The micromigration of the cage is examined when a pull out load of l00N is applied in the A-P direction. The analysis results reveal that the spike tip width significantly influences the stress concentration in the end plate, but the spike height and angle do not significantly influence the stress distribution in the end plate touching the cage's spikes. In addition, the analysis results show that the micromigration of the cage can be reduced by adjusting the spike angle and spike arrangement in the A-P direction. This study proposes the optimal shape of an intervertebral fusion cage, which promotes bone fusion, reduces the stress concentration in a vertebral end plate, and increases mechanical stability.

• Journal of Periodontal and Implant Science
• /
• v.36 no.3
• /
• pp.673-682
• /
• 2006

Recent study shows that implant design has a great impact on initial stability in bone. The ITI $TE^{(R)}$ implant, designed originally for immediate placement has a tapered/ cylindrical form which fits the anatomical shape of the natural alvelous or tooth root. The increased diameter at the collar region coupled with more threads lead to more bone contact and enhanced stability. The aim of this retrospective study is to evaluate the clinical use and the efficacy of recently introduced ITI TE implant with a new macro-design. The following results are compiled from 139 patients who received ITl TE implant surgery at the periodontal department. of Yonsei University Hospital between July 2002 and September 2005. 1. 139 patients received 173 ITl $TE^{(R)}$ implants in their maxilla and mandible (Mx 82, Mn 91). Posterior area accounted for 84% of the whole implant surgery, 2. In the distribution of bone quality, type III(41,0%) was the most, followed by type IV(41,0%) and type II (27.7%). As for the bone quantity, type B(43.9%) was the most, followed by type C(42.2%), type D(12.2%) and type A(1.7%). 3. 125 implants(83.9%) were treated by single crown, which accounted for the majority. 4, The total implant survival rate was 100% after a mean follow-up period of 21.2 months. This preliminary data with ITl $TE^{(R)}$ implant showed excellent survival rate although the majority of implants evaluated in this study were placed in the posterior region of the jaw and compromised sites.

• Korean journal of applied entomology
• /
• v.7
• /
• pp.39-51
• /
• 1969

The study involved determination of resistance levels of spider mites ta argano-phosphates using topical application and slide dip techniques; laboratory serening tests of alternative acaricides using an O/P resistant strain and a field trial of the screened materials. 1. Strains of Tetranychus were from Timaru(TR), Havelock Narth (HNR), Lincaln (LN). Germany (GR, GN). Comparisons of the resistant strains and normal strains at the LD50 and LC50 levels were as follows : (a) Using the topical application tochnique; with Parathian. resistant levels of the GR. TR and HNR strains of T. urticae were respeativuly, 1035. 484 and 452 times as resistant' as the LN strain. (b) Using the slide dip technique; with Phosdrin, resistant of GR, TR and HNR strains of T. urticae were 635, 274 and 266 times greater respeativuly, than the GN strain. 2. The laboratory sereaning tests were carried out far their contact plus stomach and residual effect to assess the toxicities of eleven alternative materials which would be used far control of O/P resistant strain of T. urticae. The acaricide groups represented were 3 organo-chlorines (Spidex, Kelthane and C 8514), 2 nitrophenyls (UC 19786 and Morocide), 2 cyclic carbonates(Eradex and Morestan). I carbamate (UC2004 7A), 1 mixture of carbamate and orano-chlorine and 2 other chemicals (C 8677 and M2527). From all acaricide tested. Kelthane and Morocide were the most effective, folowed by Spidex and M2527. Morestan, C8514. C8677 and RS 143 were intermediate, but Eradex, UC 19786 and UC 20046A were poor. 3, The number of sapmles required for estimation of the population in the field evaluation of acaricidal effects was one giving the highest practical precision. It was decided, after preliminary sampling trials. to use samples of 30 leaves per replicate which gave a $5.7\%$ standard error. 4. In the field trials, Morocide applied at the $0.05\%\;and\; 0.04\%$ a. i. conc. to black currant trees gave excellent control of O/P resistant population of T. urticae for about 12 days, but Morocide 0.025 and Kel thane $0.02\%$ a. i. cone. gave efficient control for about 6 days. In other words. first applications of Kel thane ane Moroeide gave very high degrees of control of O/P resistant population of the two-spotted spider mite. However, the results indicate that secondary application would sometimes be necessary. There was no foliage damage of black Currants and strawberries by either acaricides at the concentrations used. Acknowledgment ... The authors are grateful to: Dr. R. P. pottinger, Senior Lecturer in Agricultural Zoology. Lincoln college. New Zealand. for his helpful assistance in aiding with the organization of thd field work. Department of agriculture officers for mite colonies. Mr. D. A. Slade, Technical Advisor. Fruitgrowers' Federation (now at Massey University) for his assistance and provision of mites for testing. Mr T. McRae of Timaru for permission to use his crops for field tests. The following chemical companies and I or their New Zealand agents for so readily supplying samples of acarides; Ivan Watkins-Dow Limited. Fruitgrowers Chemical Company Limited. Henry H. York & company (New Zealand). Shell Oil (New Zealand) Limited.