• Proceedings of the Korean Society of Coastal and Ocean Engineers Conference
• /
• 2000.09a
• /
• pp.126-132
• /
• 2000

하수처리장의 수중확산관에서 방류되는 부력제트는 초기혼합, 중력확장, 이송-확산 등의 과정이 시간적, 공간적으로 규모가 상이한 범위에서 일어나며, 하수방류 해역의 주변수 흐름은 지형특성과 조석의 영향을 받아 3차원적 비정상류 특성을 나타낸다. 이러한 부력제트의 거동을 모의하기 위해서는 일반적으로 근역과 원역을 분할하여 예측하는 방법을 사용하는데, 초기혼합 과정과 중력환장 과정을 예측하기 위해서는 정상상태는 가정한 특성길이 모형이나 제트적분 모형을 사용하고, 원역으로의 이송-확산 과정을 모의하기 위해서는 농도 모형이나 임자추적 모형등을 사용한다. (중략)

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.4
• /
• pp.50-55
• /
• 2001

To simulate the combustion process under stratified charged conditions, like GDI engines, the new combustion model is proposed, which is based on Welter's FAE model and Peters' PDF model for considering primary reactions. In addition to these models, the new laminar burning velocity correlation and diffusion flame model are also included in the proposed model. The former can be applicable to much wider range of equivalence ratio, pressure and temperature than the others, such as Keck's and Guilder's models, and the latter has been derived from water-gas shift reaction and hydrogen oxidation, by which the secondary reactions can be considered after primary reactions. 3-D computation has been performed by using STAR-CD v3.05 in the simple cylindrical geometry under stratified charged condition. Judging from the calculated results, the present model proves to be reasonable to simulate the characteristics of flame propagation and concentrations of products in burned regions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.10
• /
• pp.1779-1785
• /
• 2006

This paper presents a method of virtual robot arm control by EMG pattern recognition using the proposed hybrid system. The proposed hybrid system is composed of the LVQ and the SOFM, and the SOFM is used for the preprocessing of the LVQ. The SOFM converts the high dimensional EMG signals to 2-dimensional data. The EMG measurement system uses three surface electrodes to acquire the EMG signal from operator. Six hand gestures can be classified sufficiently by the proposed hybrid system. Experimental results are presented that show the effectiveness of the virtual robot arm control by the proposed hybrid system based classifier for the recognition of hand gestures from EMG signal patterns.

• Journal of the Korea Convergence Society
• /
• v.9 no.10
• /
• pp.237-242
• /
• 2018

A micromixer is a component of a lab-on-a-chip or microfluidic device that mixes two or more chemicals together(convergence). The purpose of this study is to assess the performance of passive micromixer of various shapes. Six shapes of micromixers were compared and three dimensional modeling was carried out to have the same hydraulic diameter. The commercial code, ANSYS Fluent, was used to simulate the internal mixing flow. A numerical analysis method is described in detail in this paper. The performance of the micromixer was compared with the mixing index and pressure drop. Consequently, the CDM-8T shape showed reasonable mixing performance and relatively low pressure drop.

• Restorative Dentistry and Endodontics
• /
• v.31 no.1
• /
• pp.20-29
• /
• 2006

The purpose of this study was to analyze the stress distribution aspect of unrestored and restored combined shape (wedge shape occulusally and saucer shape gingivally) class V cavity, which found frequently in clinical cases. A maxillary second permolar restored with a combined shape class V composite restorations were modeled using the three dimensional finite element method. Static occlusal load of 170 N was applied on lingual incline of buccal cusp at the angle of $45^{\circ}$ with the longitudinal axis of the tooth. And three dimensional finite element analysis was taken by ANSYS (Version 6.0, Swanson Analysis System Co., Houston, U.S.A) program which represent the stress distribution on unrestored and restored cavity wall and margin. The conclusions were as follows. 1. Compared to the unrestored cavity, Von Mises stress at the cementoenamel junction and line angle of the cavity base were reduced and in restored cavity. 2. Von Mises stress at the occlusal and cervical cavity margin and wall were increased in restored cavity in comparison with the unrestored cavity. 3. In the hybrid and hybrid/flowable composite resin restoration, Von Mises stress at the cementoenamel junction and line angle of the cavity base were reduced more than in the flowable restoration. 4. In the hybrid and hybrid/flowable composite resin restoration, Von Mises stress at the occlusal and cervical cavity margin and wall were increased more than in the flowable restoration.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.93-98
• /
• 2007

The air velocity flowing in inner combustion chamber of SCramjet is supersonic and the time of its stay is very short as a few milliseconds. Within this short time, fuel injection， air-fuel mixing, and combustion process should be accomplished. Several methods are suggested for mixing enhancement. Among these, cavity is selected to study for mixing characteristics. The numerical simulation is performed in the case of freestream Mach number of 2.5 and cavity located in front of fuel jet injection. 3 different sized cavities of the same length-height ratio were used in order to recognize the effect about cavity size. Also, the case without cavity was analyzed to find the effect of cavity. Used code compared with the result of experiment under identical conditions and it was verified. Through this comparison and verification, mixing enhancement by cavity size could be confirmed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.9 no.3
• /
• pp.319-326
• /
• 1985

본 연구에서는 준 3차원 유한요소법(quasi 3-D finite element method)을 사 용하여 균일한 변위하중뿐 아니라 적층판의 제작 공정상 필연적인 열하중(thermal loading)의 영향을 동시에 고려하여 층간균열의 발생 및 성장에 대한 특성을 밝히고자 한다. 끝으로 층간 균열이 인장강도에 미치는 영향을 혼합법칙(rule of mixtures)의 개념을 사용하여 평가하고자 한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.359-363
• /
• 2005

In SCRamjet engine, combustion occurs in supersonic flow with airbreathing. SCRamjet is characterized by very short combustion time in combustor, so it is very important to be mixing the air and fuel in short duration. Several methods are suggested for mixing enhancement. Among these, cavity is selected to study for enhancement of mixing. The numerical simulation is performed in the case of freestream Mach number of 2.5 and cavity located in front of fuel jet injection. CFD-Fastran, commercial code with three-dimensional Navier-Stokes equation with the Menter SST turbulence model were used. The results are obtained validate experiment results for same condition. Therefore, the numerical results show the mixing enhancement characteristics with a cavity.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.8
• /
• pp.51-58
• /
• 2014

In this research, the composite grounds including original clay and soil-cement were constructed for conducting uniaxial compression test. Strength and deformation properties were analysed using results of laboratory tests with variations of water content of clay, replacement ratio and cement content. Numerical simulation using 3D distinct element method was conducted for soil cement. For strength of composite ground that contains more than cement contents of 15 %, it is more effective to increase cement content than increase of replacement ratio. Strength and elastic modulus of composite ground could be predicted by regression equations using uniaxial compression strength of clay, cement content of soil cement and replacement ratio. For strength and elastic modulus of soil cement, which is most important things for predicting final strength and elastic modulus of composite ground, numerical simulation using the distinct element method adapted bonding model could be used to verify laboratory test, and predict strength and elastic modulus.

• Smart Media Journal
• /
• v.1 no.3
• /
• pp.15-21
• /
• 2012

Depth information is necessary for various three dimensional contents generation. Depth acquisition techniques can be categorized broadly into two approaches: active, passive depth sensors depending on how to obtain depth information. In this paper, we take a look at several ways of depth acquirement. We present not only depth acquisition methods using discussed ways, but also hybrid methods which combine both approaches to compensate for drawbacks of each approach. Furthermore, we introduce several matching cost functions and post-processing techniques to enhance the temporal consistency and reduce flickering artifacts and discomforts of users caused by inaccurate depth estimation in 3D video.