• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.32 no.4_1
• /
• pp.319-326
• /
• 2014

The accurate geo-referencing processes that apply ground control points is prerequisite for effective end use of HRSI (High-resolution satellite imagery). Since the conventional control point acquisition by human operator takes long time, demands for the automated matching to existing reference data has been increasing its popularity. Among many options of reference data, the airborne LiDAR (Light Detection And Ranging) data shows high potential due to its high spatial resolution and vertical accuracy. Additionally, it is in the form of 3-dimensional point cloud free from the relief displacement. Recently, a new matching method between LiDAR data and HRSI was proposed that is based on the image projection of whole LiDAR data into HRSI domain, however, importing and processing the large amount of LiDAR data considered as time-consuming. Therefore, we wmotivated to ere propose a local LiDAR chip generation for the HRSI geo-referencing. In the procedure, a LiDAR point cloud was rasterized into an ortho image with the digital elevation model. After then, we selected local areas, which of containing meaningful amount of edge information to create LiDAR chips of small data size. We tested the LiDAR chips for fully-automated geo-referencing with Kompsat-2 and Kompsat-3 data. Finally, the experimental results showed one-pixel level of mean accuracy.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2004.03a
• /
• pp.559-564
• /
• 2004

최근들어 광범위한 지역의 삼차원 국토정보 취득을 위한 고해상도 위성영상의 센서모형화 기법에 관한 연구가 활발히 진행되고 있다. IKONOS나 SPOT 5호와 같은 고해상도 위성영상의 모형화에 앞서 본 연구에서는 각종 응용분야에서 광범위하게 활용되고 있는 SPOT 3호 위성영상을 대상으로 지상기준점을 이용하여 경사촬영(off-nadir viewing)각을 추정하는 기법을 개발하였다. 추정된 경사촬영각은 영상좌표를 보정하는데 사용되었으며 2차원 부등각사상변환을 이용하여 기존의 모형화 방법 보다 간결하고 정확도가 향상된 모형화 기법을 제안하였다. 또한, 기존의 엄밀 센서 모형화 방법을 대체하고 있는 위성영상의 센서모형화를 위한 다양한 방법들이 제안되고 있기 때문에, 2차원 부등각사상변환, 직접선형변환(DLT), 자체검정-DLT(SDLT)등의 추상화된 모형화 방법을 SPOT 위성영상에 대해 기준점 수의 변화에 따라 검사점을 이용하여 수평성분, 수직성분으로 나누어 정확도를 비교 분석하였다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.7 no.2
• /
• pp.35-43
• /
• 1989

The improvements of highly accurate and dense control networks are major requirements to carry out numerical surveying and a large scale mapping for cadastral renovation. In the most conventional photogrammetric solutions, adjusted control coordinates have been applied to block triangulations. However, this study, imploying real data and those of simulated as well, contributes to a simultaneously combined adjustment. It also contains such photogrammetric as photocoordinates and geodetic observations like distances, angles and hight differences. Its purpose is to introduce the improved results, despite it is not sufficient for the ground network. In addition, through the detection of gross error, more precise observational data can be selected for the better adjustment. All in all, the result of this study can be summarized as follows : First, even if the ground control points are not sufficient nor existed at all, the combination of pbotogrammetric and geodetic observations are improved its accuracy. Secondly, the case #2 is more accurate than that of #3, and the case #7 comes into close to that of #6.

• Proceedings of the Korea Contents Association Conference
• /
• 2005.05a
• /
• pp.138-141
• /
• 2005

본 연구에서는 위성영상으로부터 정사투영 영상을 제작하고, 지상의 기준점 측량을 GCP를 이용하여 실시하여 경도, 위도 고도의 참조좌표를 정확히 수집하였다. 1:5,000 지형도를 디지타이징하여 만들어진 등고선도를 DEM으로 변환하여 고도별 RGB영상으로 화면에 보여지도록 하고, 각각의 경우에 대하여 제작된 정사투영 영상에 중첩해 봄으로써 제작된 정사투영영상의 정확도를 점검하여 수치지형도를 대신할 수 있는 3차원 영상지도를 제작하였다. 대상지역의 입체지형분석을 위한 3차원 입체 영상지도를 제작과 더불어 DEM을 이용한 지형의 경사도 분석과 방향분석, 지형표고모델, 다방향 입체영상을 생성할 수 있도록 하였다. 장차 국토계획 및 건설분야에서의 지형분석과 각종 구조물의 배치 및 관리, 하천 수계의 분포에 대한 댐 건설 최적지 선정, 도로계획선에 따른 각 방향의 조감도 제작, 토지 피복분류에 의한 토지이용과 지역개발계획 등 지역환경을 종합적으로 진단해 볼 수 있는 활용방안을 도출할 수 있는 적용실험을 하였다.

• Proceedings of the Korea Contents Association Conference
• /
• 2007.11a
• /
• pp.27-29
• /
• 2007

The visual implementation of 3-dimensional national environment is focused by the requirement and importance in the fields such as, national development plan, telecommunication facility deployment plan, railway construction, construction engineering, spatial city development, safety and disaster prevention engineering. The currently used DEM system using contour lines, which embodies national geographic information based on the 2-D digital maps and facility information has limitation in implementation in reproducing the 3-D spatial city. Moreover, this method often neglects the altitude of the rail way infrastructure which has narrow width and long length. There it is needed to apply laser measurement technique in the spatial target object to obtain accuracy. Currently, the LiDAR data which combines the laser measurement skill and GPS has been introduced to obtain high resolution accuracy in the altitude measurement. In this paper, we first investigate the LiDAR based researches in advanced foreign countries, then we propose data a generation scheme and an algorithm for the optimal manage and synthesis of railway facility system in our 3-D spatial terrain information. For this object, LiDAR based height data transformed to DEM, and the realtime unification of the vector via digital image mapping and raster via exactness evaluation is transformed to make it possible to trace the model of generated 3-dimensional railway model with long distance for 3D tract model generation.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.3
• /
• pp.175-185
• /
• 2020

Three-dimensional registration is a process of matching data with or without a coordinate system to a reference coordinate system, which is used in various fields such as the absolute orientation of photogrammetry and data combining for producing precise road maps. Three-dimensional registration is divided into a method using points and a method using linear features. In the case of using points, it is difficult to find the same conjugate point when having different spatial resolutions. On the other hand, the use of linear feature has the advantage that the three-dimensional registration is possible by using not only the case where the spatial resolution is different but also the conjugate linear feature that is not the same starting point and ending point in point cloud type data. In this study, we proposed a method to determine the scale and the three-dimensional translation after determining the three-dimensional rotation angle between two data using quaternion to perform three-dimensional registration using linear features. For the verification of the proposed method, three-dimensional registration was performed using the linear features constructed an indoor and the linear features acquired through the terrestrial mobile mapping system in an outdoor environment. The experimental results showed that the mean square root error was 0.001054m and 0.000936m, respectively, when the scale was fixed and if not fixed, using indoor data. The results of the three-dimensional transformation in the 500m section using outdoor data showed that the mean square root error was 0.09412m when the six linear features were used, and the accuracy for producing precision maps was satisfied. In addition, in the experiment where the number of linear features was changed, it was found that nine linear features were sufficient for high-precision 3D transformation through almost no change in the root mean square error even when nine linear features or more linear features were used.

• Korean Journal of Remote Sensing
• /
• v.28 no.2
• /
• pp.191-202
• /
• 2012

A high resolution satellite imagery such as KOMPSAT-2 includes a material containing rational polynomial coefficient (RPC) for three-dimensional geopositioning. However, image geometries which are calculated from the RPC must have inevitable systematic errors. Thus, it is necessary to correct systematic errors of the RPC using several ground control points (GCPs). In this paper, we propose an efficient method for automatic correction of image geometries using tie points of a stereo pair and the Shuttle Radar Topography Mission (SRTM) Digital Elevation Model (DEM) without GCPs. This method includes four steps: 1) tie points extraction, 2) determination of the ground coordinates of the tie points, 3) refinement of the ground coordinates using SRTM DEM, and 4) RPC adjustment model parameter estimation. We validates the performance of the proposed method using KOMPSAT-2 stereo pair. The root mean square errors (RMSE) achieved from check points (CPs) were about 3.55 m, 9.70 m and 3.58 m in X, Y;and Z directions. This means that we can automatically correct the systematic error of RPC using SRTM DEM.

• Journal of Astronomy and Space Sciences
• /
• v.15 no.1
• /
• pp.183-196
• /
• 1998

The Synthetic Aperture Radar(SAR) image and the Digital Elevation Model(DEM) of an target area are put into use to generate three dimensional image map. An method of image map generation is explained. The orbit and attitude determination of satellite makes it possible to model signal acquisition configuration precisely, which is a key to mapping image coordinates to geographic coordinates of concerned area. An application is made to RADARSAT in the purpose of testing its validity. To determine the orbit, zero Doppler range is used. And to determine the attitude, Doppler centroid frequency, which is the frequency observed when target is put in the center of antenna's view, is used. Conventional geocoding has been performed on the basis of direct method(mapping image coordinates to geographic coordinates), but in this reserch the inverse method(mapping from geographic coordinates to image coordinates) is taken. This paper shows that precise signal acquisition modeling based on the orbit and attitude determination of satellite as a platform leads to a satellite-centered accurate geocoding process. It also shows how to model relative motion between space-borne radar and target. And the relative motion is described in ECIC(earth-centered-initial coordinates) using Doppler equation and signal acquisition geometry.

• The Bulletin of The Korean Astronomical Society
• /
• v.40 no.1
• /
• pp.51.3-51.3
• /
• 2015

1995년 한국 최초로 VLBI관측이 이루어졌다. 일본 측의 26m 안테나(일본 국토연구원 소재)와 한국 측의 3.6m 안테나(국토지리정보원 소재)로 수행되었으며, 이 때 결정된 관측점의 좌표가 세계 공통으로 사용되는 "세계측지계(ITRF)"에 의거한 새로운 국가기준좌표계의 경위도 원점이다. 그 후 측지VLBI관측국의 설치를 위해, "측지VLBI구축 타당성조사 및 기본계획 수립을 위한 연구(2003년)"와 "측지VLBI구축 실시설계(2006년)"를 수행하였다. 그 결과 국가 차원에서 측지VLBI관측소(22m 안테나)를 건설하기 위해 2008년에 관측소 후보지를 세종시로 확정해서 공사에 들어갔다. 2012년에 준공되었으며, 명칭을 "우주측지관측센터"로 하였다. 그 후 1년 동안의 시험관측의 성공으로 아시아에서 3번째로 정식으로 IVS(International VLBI Service)에 가입하였다. 현재 독일, 일본, 미국 등의 측지VLBI관측국들과 정기적으로 관측을 수행하게 되었으며, 실적을 올리고 있다. IVS사업 뿐 만 아니라, 한국천문연구원의 KVN(천문 VLBI)연구팀과도 공동연구를 수행해서 우리나라의 천문 VLBI 및 측지VLBI관측사업의 활성화에 기여하고 있다. 장차 동남아 각국에 마이크로SAR위성의 관측데이터를 수신하기 위한 지상국(3m급 소형안테나)이 설치되면, 이를 활용해서 측지VLBI관측을 수행할 계획을 수립하고 있다. 이것은 위성용 수신기를 VLBI용 수신기로 교체하면 된다. 한국과 일본이 VLBI관측을 수행했던 것처럼 세종시에 설치된 우주측지관측소가 허브역할을 하면 된다. 즉 동남아 지역에 우주 VLBI관측망을 구축하게 된다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.28 no.5
• /
• pp.479-484
• /
• 2010

In the airborne laser survey with GPS/INS, based on kinematic, the installation and operation of GPS base stations is necessary to allow three-dimensional location coordinates to be obtained quickly and precisely. However, in many cases, GPS base stations operate under difficult conditions. In this paper, we investigate the substitutability of continuously operating reference stations (CORS) for base stations, and we examine the influence of the distance between aircraft GPS and CORS on the Z-value. The results of our study demonstrate that, if the performance of GPS base stations within regulation distance is replaced with that of CORS, sufficient accuracy is guaranteed. Moreover, the performance of CORS beyond regulation distance is fairly good.