• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2003.04a
• /
• pp.354-362
• /
• 2003

위성영상으로부터 위치자료가 포함된 지리 및 지형정보를 얻기 위해서는 영상획득순간의 센서 위치 및 자세와 지상좌표간의 관계를 해석하여야 한다. 위성영상에 대한 수학적 모형화를 위해서 먼저 입체영상에서 지상기준점(Ground Control Point: GCP)을 선정하고, 선정된 지상기준점에 대한 지상좌표 및 대상영상에 대한 영상좌표 관측작업을 수행한다. 본 연구에서는 지상기준점 데이터베이스에 포함된 정보들을 이용하여 관측대상 입체영상 3차원 모형화에 필요한 지상기준점의 영상좌표를 자동으로 추출할 수 있는 기법을 개발하였다. 관측정밀도는 수작업으로 관측한 값과 자동계산된 영상좌표의 결과를 비교 분석하여 평가하였으며, SPOT위성영상의 3차원 모형화에 적용하여 정확도를 평가하므로써 유사한 해상도의영상을 활용하는 3차원 모형화 과정에서 지상기준점의 영상좌표 관측을 자동화 할 수 있음을 입증하였다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.2
• /
• pp.165-172
• /
• 2003

IKONOS satellite images are particularly well suited for stereo feature extraction. But, because IKONOS doesn't offer information about the satellite ephemeris and attitude, we have to use IKONOS RPC(Rational Polynomial Coefficients) data for 3-D feature extraction. In this study, it was intended to increase the accuracy and the efficiency in application of high resolution satellite images. Therefore, this study develop the program to extract 3-D feature information and have analyzed the geometric accuracy of the IKONOS satellite images by means of the change with the number, distribution and height of GCPs. This study will provide basic information for luther studies of the accuracy correction in IKONOS and high resolution satellite images.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.37 no.3
• /
• pp.189-198
• /
• 2019

In photogrammetry, single photo resection is a method of determining exterior orientation parameters corresponding to a position and an attitude of a camera at the time of taking a photograph using known interior orientation parameters, ground coordinates, and image coordinates. In this study, we proposed a single photo resection algorithm that determines the exterior orientation parameters of the camera using cosine law and linear equation-based three-dimensional coordinate transformation. The proposed algorithm first calculated the scale between the ground coordinates and the corresponding normalized coordinates using the cosine law. Then, the exterior orientation parameters were determined by applying linear equation-based three-dimensional coordinate transformation using normalized coordinates and ground coordinates considering the calculated scale. The proposed algorithm was not sensitive to the initial values by using the method of dividing the longest distance among the combinations of the ground coordinates and dividing each ground coordinates, although the partial derivative was required for the nonlinear equation. In addition, since the exterior orientation parameters can be determined by using three points, there was a stable advantage in the geometrical arrangement of the control points.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.11 no.4
• /
• pp.163-170
• /
• 1991

The 3 dimensional point positioning from SPOT imagery is performed by bundle adjustment methods of analytical and digital photogrammetry, and need the precise determination of image coordinates and accurate coordinates of ground control points. In this study, the authors analysed the digitized planimetric accuarcy and height accuracy of topographic maps in comparison with accurate coordinates by coordinates resulted by bundle adjustment in each cases between different acquisition method of ground control point coordinates and formats of SPOT imagery.

• Journal of Korean Society for Geospatial Information Science
• /
• v.11 no.2 s.25
• /
• pp.29-37
• /
• 2003

An approach is described for automatic measuring of GCP's image coordinates from SPOT imagery and focused on the fulfillment an automatic orientation of satellite images. For the orientation of a stereopair of digital images, firstly, GCP(Ground Control Point) should be selected and then the work for measuring of image coordinates correspond to GCPs is required. In this study, we propose the method for extracting the GCP's image coordinates automatically using an image patch for control points and auxiliary points matching. For the evaluation of measurement accuracy, a comparison between points those are extracted manually and automatically by a proposed method have made. Finally, we shows the feasibility of automatic image coordinates measurment by applying in stereo modeling for SPOT images.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.5
• /
• pp.191-199
• /
• 1993

Investigation is given to the detailed procedure of a computer assisted automatic technique for ortho-image generation from digital stereo image data of close-range photographs scanned by the CCD camera scanner. After rectification of geometric scanning errors, the bundle adjustment technique was used to determine the exterior orientation parameters of terrestrial camera. An automatic correlation matching technique was applied to search for the conjugate pixels in digital stereo pairs. And the 3-dimensional coordinates of the corresponding pixels were calculated by the space intersection method. For the generation of ortho-image from the calculated coordinates and right image data values, inverse-weighted-distance average method was used. And the accuracy of the resulting ortho-image was checked by comparing its image coordinates with there corresponding ground coordinates for the check points.

• Korean Journal of Remote Sensing
• /
• v.37 no.3
• /
• pp.567-575
• /
• 2021

In order to correct the provided RPC and DEM generated from the high-resolution satellite images, the acquisition of the ground control point (GCP) must be preceded. This task is a very complicate that requires field surveys, GPS surveying, and image coordinate reading corresponding to GCPs. In addition, since it is difficult to set up and measure a GCP in areas where access is difficult or impossible (tidal flats, polar regions, volcanic regions, etc.), an alternative method is needed. In this paper, we propose a 3D surface matching technique using only the established ground coordinate package, avoiding the ground-image-location survey of the GCP to correct the DEM produced from WorldView-2 satellite images and the provided RPCs. The location data of the public control points were obtained from the National Geographic Information Institute website, and the DEM was corrected by performing 3D surface matching with this package. The accuracy of 3-axis translation and rotation obtained by the matching was evaluated using pre-measured GPS checkpoints. As a result, it was possible to obtain results within 2 m in the plane location and 1 m in height.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.7 no.4
• /
• pp.139-146
• /
• 1987

The 3-dimensional deformation measurement by the terrestrial photogrammetry is consist of 3-dimensional coordinates computation, displaced point detection and deformation estimation of object targets. In this study, at the first step of deformation analysis, the variation of the variance-covariance matrix for the exterior orientation elements was analyzed by the increment of the ground control points and the photos in the Bundle adjustment. And then, to give the constraints for improving accuracy of ground control points, the concept of Free-Network adjustment was applied to Bundle adjustment. As a result, we knew that it was desired in the accuracy and the economy, the observation time when the numbers of ground control point and photo were respectively 6 points and 3 photos. In addition, in the case of applying the concept of Free Network adjustment in Bundle adjutment, it was desirable that the space distance for the constraints is distributed outside.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.4
• /
• pp.301-308
• /
• 2003

This study describes the methodology that improves the accuracy of the 3D object-space data extracted from IKONOS satellite images by improving the accuracy of a RPC(Rational Polynomial Coefficient) model. For this purpose, we developed the algorithm to adjust a RPC model, and could improve the accuracy of a RPC model with this algorithm and geographically well-distributed GCPs(Ground Control Points). Furthermore, when a RPC model was adjusted with this algorithm, the effects of geographic distribution and the number of GCPs on the accuracy of the adjusted RPC model was tested. The results showed that the accuracy of the adjusted RPC model is affected more by the distribution of GCPs than by the number of GCPs. On the basis of this result, the algorithm using pseudo_GCPs was developed to improve the accuracy of a RPC model in case the distribution of GCPs was poor and the number of GCPs was not enough to adjust the RPC model. So, even if poorly distributed GCPs were used, the geographically adjusted RPC model could be obtained by using pseudo_GCPs. The less the pseudo_GCPs were used -that is, GCPs were more weighted than pseudo_GCPs in the observation matrix-, the more accurate the adjusted RPC model could be obtained, Finally, to test the validity of these algorithms developed in this study, we extracted 3D object-space coordinates using RPC models adjusted with these algorithms and a stereo pair of IKONOS satellite images, and tested the accuracy of these. The results showed that 3D object-space coordinates extracted from the adjusted RPC models was more accurate than those extracted from original RPC models. This result proves the effectiveness of the algorithms developed in this study.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.4
• /
• pp.423-431
• /
• 2008

The control surveying which aims at identifying the coordinate system of satellite images with that of ground is a repeatedly performed essential process to produce digital ortho - photos and it acts as the main factor to increase the production cost of the photos by duplicated budgets and redundant works when executing the projects for acquiring basic geographical information from high density satellite images. During the experimentation, an application system was established for producing a stereo image chip by the analysis of DPPDB file structure, the stereo image chip was produced with SPOT and IKONOS images, the analysis of 3D modeling accuracy was performed to secure the required accuracy and to present the optimal number and deployment of the control points, and a 3D modeling was performed for new SPOT images and lastly, 3D ground coordinates were extracted by the observation of the same points through the overlapping with the new images. As the results of the research, it is proved that the stereo image chip can be used as the ground controls through the accuracy analysis between the coordinates of the images and the ground, close results were obtained between the coordinates by the ground survey and those by the 3D modeling using new images and the observation of the same points, positional changes were not found during observing the same points, and the research presented the methodology for improving the process of the control survey by showing the availability of the image controls on the stereo image chip instead of the ground controls.