• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.285-294
• /
• 2002

Embankment Piles, which is subjected to damage due to lateral movement of soft ground, can be classified into pile slab, cap beam pile, and isolated cap pile according to the installation pattern of pile cap. In the cap beam pile and the isolated cap pile method, the soil arch is developed by the different stiffness between pile and soil, and most embankment loads are transferred into embankment piles through soil arch. In these two methods, the difference of soil arch is that the soil arch of the cap beam pile method develops like the arch from of tunnel between cap beams and the soil arch of the isolated cap pile method develops like dome between isolated caps. Therefore, theoretical analysis methods on soil arching effect of the cap beam pile and the isolated cap pile method were respectively proposed according to their own arch form considering the limiting equilibrium of stresses in a crown of soil arch. And a series of model tests were performed both to investigate the load transfer by soil arching in fills above embankment piles and to verify the reliability of the theoretical analysis.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.185-185
• /
• 2011

기존 장대레일 궤도의 안정성 평가는 궤도 매개변수에 대하여 고정된 안전측의 값을 사용하는 결정론적인 해석에 의존해서 평가되어져 왔다. 그러나 실제현장의 궤도조건은 많은 영향인자들에 의해 그 특성이 불확실하게 변하고 있다. 따라서 온도하중에 의한 궤도 좌굴에 영향을 미치는 궤도 구성인자들의 불확실성 및 임의성을 보다 합리적으로 고려하기 위해서 확률론적 기법을 적용하는 것이 필수적이다. 본 연구에서는 기존 본 연구진에 의해 개발된 장대레일 궤도의 좌굴확률 평가시스템을 이용하여 좌굴 취약도 곡선을 나타내었으며, 궤도 좌굴에 영향을 미치는 주요변수 중 하나인 도상횡저항력에 대한 영향을 분석하였다. 좌굴확률 평가시스템에서는 장대레일 궤도의 좌굴확률을 산정하기 위하여 구조물의 안정과 파괴를 판단할 수 있는 기준을 한계상태방정식으로 표현하고, 이 한계상태방정식으로부터 확률론적 기법 중 하나인 AFOSM(Advanced First Order Second Moment) 방법을 이용하여 파괴확률의 간접적인 지표인 신뢰도지수(${\beta}$)를 통해 좌굴확률을 계산한다. 한계상태방정식에서 구조물의 강도(보유성능)에 해당하는 부분은 궤도의 허용좌굴온도이고, 하중(요구성능)에 해당하는 부분은 레일온도하중으로써 현재 레일온도와 중립온도의 차로 반영된다. 허용좌굴온도 산정에 고려되는 주요변수는 곡선반경(Radius), 도상횡저항력(Lateral Ballast Resista nce), 연직도상강성(Vertical Ballast Stiffness), 궤도 틀림량(Misalignment), 틀림길이(Half Wave Length), 열차운행속도(Velocity)이다. 각 확률변수들이 갖는 확률분포는 모두 정규분포로 가정하였다. 궤도의 기하학적 특성은 곡선반경 5,000m에 대해 고려하였으며, 열차는 KTX의 제원을 사용하여 정지된 상태에서 고려하였다. 틀림량과 틀림길이는 이에 대한 통계적 특성자료가 부족하여 확률변수로 고려하지 않고 결정론적 값으로 취급하였다. 레일온도의 통계적 특성치는 본 연구진에 의해 구축된 기후요소 및 레일온도 DB를 근거로 결정하였으며, 중립온도는 선로관리지침에 따라 $25{\pm}3^{\circ}C$를 기준으로 결정하였다. 또한 도상횡저항력은 실측 데이터를 참고로 하여 평균값에서 10%의 변동량을 갖는 것으로 보고 통계적 특성치를 결정하였다. 도상횡저항력이 좌굴확률에 미치는 영향을 매우 큰 것을 알 수 있었으며, 레일온도 $60^{\circ}C$일 때 도상횡저항력이 증가하면서 감소되는 좌굴확률이 도상저항력이 커질수록 그 감소량이 작아지는 것을 알 수 있었다.

• The Journal of Society for e-Business Studies
• /
• v.9 no.3
• /
• pp.207-226
• /
• 2004

SCM is one of the important key issues in Internet-based business environment. Most of companies related to B2B electronic commerce are making their efforts to innovate their existing business process into new integrated supply chain process. SCM system using XML/EDI provides competitive advantage to them by reshaping the relationship between traditional trading partners. This study intends to suggest a prototype of SCM system using XML/EDI. To implement SCM system, we analyze and design the supply chain process by using Unified Modeling Language, with a firm engaged in Korean automobile industry, which is a first vendor to produce a set of LAMP. The implementation of SCM system using UML shows excellent performance in software reuse, extensibility, and the interoperability with corporate internal information systems.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.3
• /
• pp.99-106
• /
• 1990

This study was aimed to see the effect of chemical grout on fresh granite joint shear strength. The grouting chemical used in this study was composed of 25% water glass. Direct shear tests were performed on the chemical filled joints, which had been made artificially with granite. The test results show that chemical grouted rock jonts have markedly reduced shear strength comparing with the ungrouted fresh joints and they sheared within chemical grout before the rock to rock contact had been established, while the ungrouted joint sheared between rock surfaces from the beginning of shear deformation. With chemical grouted joints the shear stress slowly reached its maximum without showing distinct peak shear strength. Therefore the shear stiffness of joints were decreased with increasing thickness of grout. but the shear strain at failure was increased with it.

• Composites Research
• /
• v.23 no.1
• /
• pp.44-50
• /
• 2010

In this paper, two different experiments, namely, salt water spray and salt water immersion, were performed to reproduce the contact of composites with the seawater for three kinds of woven fabric composite material systems which would be used for the WIG(wing in ground effect)craft. After aging 140 days in the salt water environment, material properties of carbon/epoxy and glass/epoxy composite such as tensile, compressive and shear stiffness and strength, and inter-laminar shear strength (ILSS) were measured. By comparing baseline material properties with degraded ones, the effects of the salt water environment on the composite mechanical properties were evaluated. From the experiments, it was confirmed that the difference in aging conditions had very small influence on composite properties. And it was found that tensile strength of carbon/epoxy composites showed little degradation, but much more degradation was observed in glass/epoxy composites. And large degradations on matrix dominant properties were observed. The salt water could damage the fiber-matrix interface, matrix properties and the glass fiber.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.21 no.6
• /
• pp.729-736
• /
• 2015

In this paper, It was performed to optimize for the deck's structural design of a double ended car ferry ship respect to Goal-Driven Optimization (GDO). It was examined for the strength and deformation of the deck and determined to save economic cost the optimal point. The deck thickness based on the Design of Experiments (DOE) and response surface method was increased to 110%. and can improve the deck's strength and stiffness. By performing the regression analysis respect to the result, we propose the optimal regression model formula as a third degree polynomial regression models. The coefficient of determination $R^2$ was about 0.98 and reliability could be obtained.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.3
• /
• pp.56-65
• /
• 1996

Recently, with development of mechanics of materials, as pursuing the high speed of the ships, there has been an increasing demand on the composite construction which satisfies high strength and low weight at the same time. A sandwich element is a type of composite construction, which is composed of thin, strong, stiff and relatively high density faces and a thick, light, and weaker core material. As the second moment is increased by faces separated from the neutral axis farther, a sandwich element is most effective light structural form. In this study, Rayleigh-Ritz Energy Method is adopted, which can analyze sandwich plate relatively simply and exactly. Stresses and buckling loads are analyzed exactly, when uniform lateral pressure load, inplane compression and inplane shear are acting at the sandwich plate. Including a wrinkling stress, this study can be applied to the initial design and minimum weight design of sandwich plates.

• Journal of the Korean Society for Railway
• /
• v.11 no.3
• /
• pp.334-341
• /
• 2008

Ballast track needs maintenance works because it is supported by the compressible trackbed and subgrade layers. Maintenance works are essential to secure riding comfort and extend the life cycle of it. The necessities of maintenance works are determined from track irregularities measured by EM120. Track irregularities is the results of the track deformation. Therefore, it is natural to evaluate the cause of it. This paper focuses on the points the track irregularities come from the trackbed and the subgrade. Nondestructive techniques, such as Ground Penetrating Radar (GPR) and Portable Falling Weight Deflectometer (PFWD) are applied to evaluate the trackbed conditions, ballast layer thickness and vertical track stiffness, in the test section 500m long of Gyungbu line. The trackbed investigation results are compared with the track irregularities measured by EM120 and maintenance works. Conclusively, it was found that some maintenance works were unnecessary on the test section.

• Journal of Digital Convergence
• /
• v.10 no.4
• /
• pp.287-295
• /
• 2012

This study aims to develop the methods for effective patient flow in the medical center through simulation modeling. To achieve this, we developed three simulation scenarios based on max/min processing time and addition of X-ray by 15 patient tracks from real hospital data. The simulation software used in this study is Flexsim HC 2.7. According to the scenario 1 on 15 patient tracks' LOS by max processing time, there is a great difference between average length of stay(LOS) and max LOS. And average LOS increases greatly depending on the number of patients by the hours. There is no need to add extra X-ray because the addition of X-ray has not much influence in average LOS. It is possible to make good decisions on patient flow management and medical equipment purchasing through simulation modeling. The concrete simulation scenario as a tool for decision support will contribute to efficiency in hospital management.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.784-787
• /
• 2002

We prepared the PLT(28) thin film by using sol-gel method and investigated the structure and electrical properties of the film. With the XRD and AFM analyses, it is found that PLT(28) thin film annealed at 6sot has a complete perovskite structure and its surface roughness is about 22$\AA$. We prepared PLT(28) thin film on the Pt/TiO$_{x}$SiO$_2$/Si substrate, in which the specimen has a planar capacitor structure, and analyzed the electrical properties of PLT(28) thin film. In result, PLT(28) thin film has a paraelectric phase and its dielectric constant and loss tangent at 10kHz are 761 and 0.024, respectively. Also, the storage charge density and leakage current density of PLT(28) thin film at W are 134fC/$\mu$m2 and 1.01 $\mu$A/cm2, respectively. As a result of this, we concluded that the PLT(28) thin film is a promising material to be used as a capacitor dielectrics for next generation DRAM.M.