• Korean Chemical Engineering Research
• /
• 제45권6호
• /
• pp.566-572
• /
• 2007

본 연구에서는 DME 직접 합성을 위한 혼성촉매가 두 가지 방법으로 제조되었으며, 이들의 촉매적 활성이 조사되었다. DME 합성을 위한 혼성촉매는 메탄올 합성과 메탄올 탈수반응에 촉매적 활성을 가진 성분들로 제조되었다. 메탄올 합성촉매는 Cu와 Zn이 함유된 전구물질로부터 합성되었으며, 메탄올 탈수촉매는 ${\gamma}-Al_2O_3$를 이용하였다. 두 촉매는 물리혼합법과 침전법에 의해서 혼성촉매로 제조되었다. 물리혼합법은 두 촉매를 분말상태에서 혼합하는 것이며, 침전법은 ${\gamma}-Al_2O_3$ 촉매상에 Cu-Zn 또는 Cu-Zn-Al 성분을 퇴적시키는 방법이다. 제조된 촉매의 물리적 특성을 조사하기 위하여 X선 회절법에 의한 결정구조, 질소흡착에 의한 BET 표면적, $N_2O$ 화학흡착에 의한 Cu의 표면적 그리고 주사전자현미경에 의한 표면형상 등이 조사되었다. 또한 이들 혼성촉매의 촉매적 활성은 여러 가지 반응조건을 변화시키면서 조사되었다. 이때 반응온도는 $250{\sim}290^{\circ}C$, 반응압력은 30~70 atm, $[H_2]/[CO]$ 몰비는 0.5~2.0, 그리고 공간속도는 $1,500{\sim}6,000 h^{-1}$ 촉매활성이 조사되었다. 반응성 실험 결과로부터 침전법으로 제조된 혼성촉매(CP-CZA/D)가 물리혼합법으로 제조된 혼성촉매(PM-CZ+D)보다 우수한 반응성을 나타냄을 확인할 수 있었으며, 특히 반응 온도, 압력, $[H_2]/[CO]$ 비, 공간속도가 각각 $260^{\circ}$, 50 atm, 1.0, $3,000h^{-1}$인 조건에서 침전법에 의해 제조된 촉매의 CO 전화율이 72%로 물리혼합법으로 제조된 촉매보다 약 20% 이상 높았다. $N_2O$ 화학흡착실험으로부터 Cu 표면적을 측정한 결과, PM-CZ+D 혼성촉매보다 CP-CZA/D 혼성촉매의 Cu 표면적이 더 높았다. 그러므로 침전법으로 제조된 혼성촉매상의 Cu입자가 더 잘 분산되었기 때문에 촉매의 활성이 개선된 것으로 판단된다.

• 한국환경과학회지
• /
• 제26권9호
• /
• pp.999-1011
• /
• 2017

In this study, the Chiu-2D velocity-flow rate distribution based on theoretical background of the entropy probability method was applied to actual ADCP measurement data of Gangjung Stream in Jeju from July 2011 to June 2015 to predict the parameter that take part in velocity distribution of the stream. In addition, surface velocity measured by SIV (Surface Image Velocimeter) was applied to the predicted parameter to calculate discharge. Calculated discharge was compared with observed discharge of ADCP observed during the same time to analyze propriety and applicability of depth of water velocity average conversion factor. To check applicability of the predicted stream parameter, surface velocity and discharge were calculated using SIV and compared with velocity and flow based on ADCP. Discharge calculated by applying velocity factor of SIV to the Chiu-2D velocity-flow rate distribution and discharge based on depth of water velocity average conversion factor of 0.85 were $0.7171m^3/sec$ and $0.5758m^3/sec$, respectively. Their error rates compared to average ADCP discharge of $0.6664m^3/sec$ were respectively 7.63% and 13.64%. Discharge based on the Chiu-2D velocity-flow distribution showed lower error rate compared to discharge based on depth of water velocity average conversion factor of 0.85.

• Journal of Animal Science and Technology
• /
• 제64권3호
• /
• pp.443-461
• /
• 2022

This study was conducted to assess the effects of the dietary supplementation of riboflavin (as a bile salt hydrolase [BSH] inhibitor) and Bacillus subtilis on growth performance and woody breast of male broilers challenged with Eimeria spp. Intestinal bacteria, including supplemented probiotics, can produce BSH enzymes that deconjugate conjugated bile salts and reduce fat digestion. A 3 × 2 × 2 (riboflavin × Bacillus subtilis × Eimeria spp. challenge) factorial arrangement of treatments in randomized complete block design was used. On d 14, birds were gavaged with 20× doses of commercial cocci vaccine (Coccivac^R -B52, Merck Animal Health, Omaha, NE). Dietary treatment of riboflavin and B. subtilis did not affect body weight (BW), body weight gain (BWG), and feed conversion (FCR) d 0 to 14 and overall d 0 to 41. Eimeria spp challenge reduced BWG, feed intake (FI), and increased FCR between d 14 to 28, but increased BWG and lowered FCR between d 28 to 35. There were no effects of the Eimeria spp. challenge on the overall d 0 to 41 FCR and FI, but BWG was reduced. Eimeria spp. challenge increased the abdominal fat pad weight and slight woody breast incidences on processed birds on d 42. Dietary inclusion of B. subtilis and riboflavin at tested levels did not help birds to mitigate the negative impact of Eimeria spp. challenge to enhance the growth performance.

• 한국농촌건축학회논문집
• /
• 제21권4호
• /
• pp.25-36
• /
• 2019

The purpose of the study is to analyze how to document survey and repair data on wooden architecture culture assets. Documentation was analyzed in comparison to digital developments from the past to the present. Although the accuracy of survey equipment has been improved by digital development, survey drawing has not changed. For example, a 3D Scanner, survey equipment, was introduced but is being used for conversion into 2D data. Data provided by the drawing included in the survey and repair reports were not accumulated. As it stands, it is inaccessible and disorganized. Data generated from the survey, repair, and maintenance has to be consistent. A BIM system was proposed to integrate information on wooden architecture cultural assets.

• Biomolecules & Therapeutics
• /
• 제20권4호
• /
• pp.393-398
• /
• 2012

Recently, we reported that defective autophagy may contribute to the inhibition of the growth in response to PP2 (4-amino-5-(4-chlorophenyl)-7-(t-butyl)pyrazolo[3,4-d]pyrimidine), a selective SFK inhibitor, in multidrug-resistant v-Ha-ras-transformed NIH 3T3 cells (Ras-NIH 3T3/Mdr). In this study, we demonstrated that PP2 induces LC3 conversion via a mechanism that is uncoupled from autophagy and increases apoptosis in Ras-NIH 3T3/Mdr cells. PP2 preferentially induced autophagy in Ras-NIH 3T3 cells rather than in Ras-NIH 3T3/Mdr cells as determined by LC3-I to LC3-II conversion and GFP-LC3 fluorescence microscopy. Beclin 1 knockdown experiments showed that, regardless of drug resistance, PP2 induces autophagy via a Beclin 1-dependent mechanism. PP2 induced a conformational change in Beclin 1, resulting in the enhancement of the pro-autophagic activity of Beclin 1, in Ras-NIH 3T3 cells. Further, PI3K inhibition induced by wortmannin caused a significant increase in apoptosis in Ras-NIH 3T3 cells, as demonstrated by flow cytometric analysis of Annexin V staining, implying that autophagy inhibition through PI3K increases apoptosis in response to PP2 in Ras-NIH 3T3 cells. However, despite the fact that wortmannin abrogates PP2-induced GFP-LC3 punctae formation, some LC3 conversion remains in Ras-NIH 3T3/Mdr cells, suggesting that LC3 conversion may occur in an autophagy-independent manner. Taken together, these results suggest that PP2 induces LC3 conversion independent of PI3K, concomitant with the uncoupling of LC3 conversion from autophagy, in multidrug-resistant cells.

• 한국통신학회논문지
• /
• 제19권11호
• /
• pp.2228-2237
• /
• 1994

This paper describes the development of a Ku-band ($12.25GHz\sim12.75GHz$) SSPA intended as a replacement for TWTAs used in communication satelite transponder. The power stage of the amplifier consists of tow intrmally matched 8W FET divices combined using the branch-line coupler. To operate this stage, the drive stage has been designed with intermally matched 2W, 4W, 8W FET and two medium power FETs. The entire amplifier is made up by a aluminum chassis housing both the RF circuit and the bias circuitry. A regrlator/sequencing circuitry is used for FET biasing. The amplifier results implemented in this way show $41\pm0.3dB$ small-signal gain, 15W saturation power, a typical two tone $IM_3=-21.5dBc$ with single carrier backed off 5dB from saturation, $2^*/dBmax$ AM/PM conversion, and $3.47\pm0.25nsec$ group delay.

• 한국멀티미디어학회논문지
• /
• 제20권2호
• /
• pp.352-362
• /
• 2017

This paper proposes an algorithm for automatically converting and displaying rainfall radar data on a 3D GIS platform. The weather information displayed like rainfall radar data is updated frequently and large-scale. Thus, in order to efficiently display the data, an algorithm to convert and output the data automatically, rather than manually, is required. In addition, since rainfall data is extracted from the space, the use of the display image fused with the 3D GIS data representing the space enhances the visibility of the user. To meet these requirements, this study developed the Auto Data Converter application that analyzes the raw data of the rainfall radar and convert them into a universal format. In addition, Unity 3D, which has good development accessibility, was used for dynamic 3D implementation of the converted rainfall radar data. The software applications developed in this study could automatically convert a large volume of rainfall data into a universal format in a short time and perform 3D modeling effectively according to the data conversion on the 3D platform. Furthermore, the rainfall radar data could be merged with other GIS data for effective visualization.

• 한국항행학회논문지
• /
• 제15권5호
• /
• pp.789-794
• /
• 2011

본 논문에서는 7.9 GHz~8.4 GHz 에서 동작하는 위성통신용 X-밴드 TWT의 AM-AM과 AM-PM 변환특성을 분석하고 선형화기를 이용하여 선형성과 IMD 특성을 개선하였다. 선형화기를 포함하는 TWT는 개선된 AM-AM과 AM-PM 변환특성을 나타내며, 1 dB 압축점은 12.3 dB, $2.0^{\circ}/dB$ 위상왜곡점은 10 dB 개선되었다. 또한 동작출력에서 3차 상호변조 특성인 IMD3는 16.2 dB 개선되어 37.0 dBc로 측정되었다. 또한, 고출력 증폭기의 IMD 측정 방안을 제시하고, TWT의 AM-PM 왜곡 특성을 보상하여 출력전력과 선형 특성을 개선할 수 있음을 나타내었다.

• 한국전자파학회논문지
• /
• 제27권10호
• /
• pp.941-944
• /
• 2016

본 논문에서는 차량 충돌 방지 및 생활 감시용 근거리 레이다(Short Range Radar: SRR)를 위한 24 GHz 전력증폭기를 삼성 65-nm CMOS 공정을 이용하여 설계하였다. 제안한 회로는 2단 차동 전력증폭기로 공통소스 구조를 사용하고, 트랜스포머 구조를 사용하여 단일 대 차동변환, 임피던스 정합, 전력결합을 하였다. 측정결과, 24 GHz에서 15.5 dB의 최대 이득과 3.6 GHz의 3 dB 대역폭을 얻었다. 측정된 최대 출력 전력은 13.1 dBm, 입력 $P1_{dB}$는 -4.72 dBm, 출력 $P1_{dB}$는 9.78 dBm이며, 측정된 최대 전력 효율은 17.7 %이다. 본 전력증폭기는 1.2 V의 공급전원으로부터 74 mW의 DC 전력을 소모한다.

• Biomedical Engineering Letters
• /
• 제8권4호
• /
• pp.337-344
• /
• 2018

Additive manufacturing (AM) is an alternative metal fabrication technology. The outstanding advantage of AM (3D-printing, direct manufacturing), is the ability to form shapes that cannot be formed with any other traditional technology. 3D-printing began as a new method of prototyping in plastics. Nowadays, AM in metals allows to realize not only net-shape geometry, but also high fatigue strength and corrosion resistant parts. This success of AM in metals enables new applications of the technology in important fields, such as production of medical implants. The 3D-printing of medical implants is an extremely rapidly developing application. The success of this development lies in the fact that patient-specific implants can promote patient recovery, as often it is the only alternative to amputation. The production of AM implants provides a relatively fast and effective solution for complex surgical cases. However, there are still numerous challenging open issues in medical 3D-printing. The goal of the current research review is to explain the whole technological and design chain of bio-medical bone implant production from the computed tomography that is performed by the surgeon, to conversion to a computer aided drawing file, to production of implants, including the necessary post-processing procedures and certification. The current work presents examples that were produced by joint work of Polygon Medical Engineering, Russia and by TechMed, the AM Center of Israel Institute of Metals. Polygon provided 3D-planning and 3D-modelling specifically for the implants production. TechMed were in charge of the optimization of models and they manufactured the implants by Electron-Beam Melting ($EBM^{(R)}$), using an Arcam $EBM^{(R)}$ A2X machine.