• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.30 no.3
• /
• pp.150-160
• /
• 1994

Drift gillnet fishery for neon flying squid in the North pacific was one of the major pelagic fisheries of Korea until 1992, its annual catch was 79, 000M/T as average during 1988-1992, but moratoriumed since 1993 according to the decision of UN. Therefore, for the developing of the new fishing gear for the squid, the seven types of rip hook by automatic squid jigging machine were experimented by the korean research vessel Pusan 851 (G/T 1.126, 2.600 PS) in the North Pacific (38 $^{\circ}$30'-43 $^{\circ}$N, 152 $^{\circ}$E-178 $^{\circ}$W) from July 6. 1993 to August 31. 1993. The investigation on catch rate, dropout rate, and catch condition of the rip hooks related to the fishing lamp power for aggregating the squid were carried out during the period. The results obtained are as follows: The composition of catch by automatic squid jigging machine was 83.9% for neon flying squid. 15.5% for boreopacific gonate squid. 0.6% for boreal clubhook squid, and 0.01% for luminous flying squid. The catch rate of neon flying squid was 94.6% in 13.6-18.3$^{\circ}C$ of surface water temperature and 5.4% in others. The higher catch rate of neon flying squid was made in the range 13.6-18.3$^{\circ}C$ of temperature at the surface and about 1$0^{\circ}C$ of temperature at the 100m layer. The CPUE of neon flying squid in the 13.6-18.3$^{\circ}C$ of surface water temperature was ranged 0.8-11.8kg (8.7kg as average). The mantle length and body weight of neon flying squid caught in the experiment were ranged 18.3-51.3 cm, 140-3, 980g and mean mantle length and mean body weight were 29.4cm, 972g respectively. The catch rate of neon flying squid was the highest at dawn with a value of 25.0% of the total catch. The body weight of neon flying squid caught by the D type hooks was 1.7 times more than that of the A type hooks. The dropout rate of neon flying squid caught by the seven types hooks was 7.9-57.5% (19.0% as average), and dropout rate of the D type hooks was 7.9% with 2.7 times decrease than that of the A type hooks. The catch efficiency of small sized neon flying squid in case of using on-off switch method on fishing lamp in 15 minutes intervals was 2.6 times higher than that of the on-switch method with same fishing lamp power.

• Journal of the Korean Society of Safety
• /
• v.26 no.1
• /
• pp.8-14
• /
• 2011

Noise and vibration are likely to disturb the sensory system of human body leading to psychological stress and thereby property damage. In this research, a cut out switch(COS) with a built-in acoustic absorber along with a COS fuse broken was developed to reduce percussion noise. This new system is based on a design approach that combines existing absorber systems: expansion type, resonator type, and acoustic absorber type silencer The noise performance of the new system was simulated using the $SYSNOISE^{TM}$ software under optimized parameters: the diameter of perforated plate 2 mm, the plate thickness 3 mm, the width of expansion room 25 mm, the impinging vortex room 14 mm, and the noise absorbtion room 10 mm. The results showed that it reduced noise by approximately 41.1 dB compared to the current systems available in the market. Furthermore, it showed reduced noise by approximately 12 dB more than a product with an acoustic absorber of the Fault Tamer(USA).

• Proceedings of the Optical Society of Korea Conference
• /
• 1991.06a
• /
• pp.22-22
• /
• 1991

광의 병렬처리 능력을 잘 활용한 1$\times$4 매트릭스 스위치의 구조와 전극구조를 설계하고 스위치 특성을 조사하기 위하여 beam propagation method(BPM)를 이용하여 수치계산을 하였다. 기존의 매트릭스 스위치는 대부분의 경우 방향성 결합기를 스위치 element로 이용하여 왔으나 이 결합기는 소자의 길이가 길기 때문에 단일 LinBO3 웨이퍼상에 집적할 수 있는 매트릭스 스위치의 크기가 제한되는 단점이 있다. 본 연구에서는 두 도파로 사이에 세 번째 도파로를 삽입하여 두 도파로를 결합시키는 세 도파로 결합기를 스위치 element로 사용하여 세 개의 스위치 element를 LiNbO3기판위에 직렬로 집적시킨 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치를 구성하였다. 스위치 element와 1$\times$4 매트릭스 스위치의 특성을 BPM을 사용하여 수치계산할 때 단일 모드 도파로의 유효 굴절을 분포는 n(X) = nm + $\Delta$ncosh-2(2x/w)의 형태로 가정했으며, 사용된 파라미터의 값은 각각 nm=2.1455, $\Delta$n=0.003, W=5$mu extrm{m}$, d=5$\mu\textrm{m}$, λ=1.3$\mu\textrm{m}$ 이고 S-파라메터의 값은 0.95927이므로 단일 모드 도파로가 된다. 계산결과 스위치 element의 결합길이는 3810$\mu\textrm{m}$이며 도파로의 길이가 결합길이와 같을 때 전극에 인가된 전압에 의한 도파로의 굴절을 섭등의 함수로 출력광의 세기를 계산한 결과 스위칭 전압은 14.85volt이고 crosstalk는 -18.9dB였다. 이 스위치 element로 구성된 1$\times$4 매트릭스 스위치는 스위칭 전압을 세 개의 전극에 적절한 조합으로 인가함으로써 한 입력 도파로에 결합된 광이 내개의 출력 도파로중 한 도파로에 스위칭 된다. 한편 수치계산의 결과를 실험적으로 확인하기 위해 스위치 element와 1$\times$4 매트릭스 스위치를 z-cut의 LinbO3 결정에 Ti을 열확산시켜 제작한 소자의 스위칭 특성을 발표할 예정이다.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.1
• /
• pp.149-155
• /
• 2015

This paper proposes 5-MS/s 10-bit digital-to-analog converter(DAC) with the improved linearity. The proposed DAC consists of a 10-bit R-2R-based DAC, an output buffer using a differential voltage amplifier with rail-to-rail input range, and a band-gap reference circuit for the bias voltage. The linearity of the 10-bit R-2R DAC is improved as the resistor of 2R is implemented by including the turn-on resistance of an inverter for a switch. The output voltage range of the DAC is determined to be $2/3{\times}VDD$ from an rail-to-rail output voltage range of the R-2R DAC using a differential voltage amplifier in the output buffer. The proposed DAC is implemented using a 1-poly 8-metal 130nm CMOS process with 1.2-V supply. The measured dynamic performance of the implemented DAC are the ENOB of 9.4 bit, SNDR of 58 dB, and SFDR of 63 dBc. The measured DNL and INL are less than +/-0.35 LSB. The area and power consumption of DAC are $642.9{\times}366.6{\mu}m^2$ and 2.95 mW, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.79-80
• /
• 2009

The local oxidation using an atomic force microscopy (AFM) is useful for Si-base fabrication of nanoscale structures and devices. SiC is a wide band-gap material that has advantages such as high-power, high-temperature and high-frequency in applications, and among several SiC poly types, 4H-SiC is the most attractive poly type due to the high electron mobility. However, the AFM local oxidation of 4H-SiC for fabrication is still difficult, mainly due to the physical hardness and chemical inactivity of SiC. In this paper, we investigated the local oxidation of 4H-SiC surface using an AFM. We fabricated oxide patterns using a contact mode AFM with a Pt/Ir-coated Si tip (N-type, $0.01{\sim}0.025\;{\Omega}cm$) at room temperature, and the relative humidity ranged from 40 to 50%. The height of the fabricated oxide pattern ($1{\sim}3\;nm$) on SiC is similar to that of typically obtained on Si ($10^{15}{\sim}10^{17}\;cm^{-3}$). We perform the 2-D simulation to further analyze the electric field between the tip and the surface. Whereas the simulated electric field on Si surface is constant ($5\;{\times}\;10^7\;V/m$), the electric field on SiC surface increases with increasing the doping concentration from ${\sim}10^{15}$ to ${\sim}10^{17}\;cm^{-3}$. We demonstrated that a specific electric field ($4\;{\times}\;10^7\;V/m$) and a doping concentration (${\sim}10^{17}\;cm^{-3}$) is sufficient to switch on/off the growth of the local oxide on SiC.

• Progress in Superconductivity and Cryogenics
• /
• v.18 no.1
• /
• pp.33-36
• /
• 2016

Suppression of the superconducting transition temperature ($T_c$) of NbN thin films in superconductor/ferromagnet multilayers has been investigated. Both superconducting NbN and ferromagnetic FeN layers were deposited on thermally oxidized Si substrate at room temperature by using reactive magnetron sputtering in an $Ar-N_2$ gas mixture. The thickness of FeN films was fixed at 20 nm, while the thickness of NbN films was varied from 3 nm to 90 nm. $T_c$ suppression was clearly observed in NbN layers up to 70 nm thickness when NbN layer was in proximity with FeN layer. For a given thickness of NbN layer, the magnitude of $T_c$ suppression was increased in the order of Si/FeN/NbN, Si/NbN/FeN, and Si/FeN/NbN/FeN structure. This result can be used to design a spin switch whose operation is based on the proximity effect between superconducting and ferromagnetic layers.

• ETRI Journal
• /
• v.32 no.3
• /
• pp.468-471
• /
• 2010

A compact square patch antenna with reconfigurable circular polarization (CP) at 2.4 GHz is proposed. Circular polarization is generated by an arc-shaped slot on the ground plane. In order to switch the CP orientation, the current flow direction of the patch is reconfigured via the PIN diodes mounted on the slot. As the slot and bias circuit are not placed on the patch side, the proposed antenna radiates a CP wave without alteration in the main beam direction. From the experimental results, the impedance and CP bandwidths of the proposed antenna have been demonstrated for up to 80 MHz and 25 MHz, respectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.6
• /
• pp.149-157
• /
• 2014

This paper is based on the fabrication of wireless control system for the building shading device. RF Module was controlled by UHF wireless CC1020 chip which has low electrical power and low electrical voltage. Also 447.8625~447.9875 frequency, 4800Baud data rate and 12.5 kHz channel spacing was controlled by the use of SPDT switch and with Microcontroller program. Furthermore, the helical antenna was used. The starting production of 447.8625~447.9875 kHz wireless electrical power was used. As the result, it did not exceed 10dBm which is the standard of low power wireless system. Shading efficiency was measured at 25%, 50%, 75% direction with controlling the interior temperature and the intensity of illumination at the rate of 1 hour. As the result, the intensity of illumination was lowered to 82~87% at 25% direction with $0.6{\sim}1.4^{\circ}C$ lowered temperature. At 50% direction, the intensity of illumination was lowered to 60~68% with $2.3{\sim}4.1^{\circ}C$ lowered temperature. And at 75% direction, the intensity of illumination was lowered to 41~47% with $3.4{\sim}5.1^{\circ}C$ lowered temperature.

• Korean Journal of Heritage: History & Science
• /
• v.46 no.2
• /
• pp.26-45
• /
• 2013

Sudden increase exceeding 30million in the number of smart phone users, and rising interest in the technology of augmented reality, is now trying to combine it with AR technology in other areas very much. The field of cultural heritage, which has been constructed by the Internet and 3D technology, is not unusual and this field is now rapidly changing thanks to the AR technology which can make users experience cultural heritage with high reality. The Palaces in Seoul, however, use fragmentary tools of information - lack of heritage commentators, leaflet, etc, even though the number of visitors is gradually increasing. Therefore, three-dimensional and comprehensive cultural heritage information service is needed with the guidance in the mobile era. This study utilizes the AR technology for building the Deoksugung Tourist Information Service Application(App.) applying the markerless-based recognition technology which is a more advanced tool than the location-based AR technology. This new AR technology can switch perceived real images such as the tablet of the King in the Palace of in the real world, patterns and pedestals into virtual world, which can reproduce the damaged cultural assets as 3D. This also composes photos of the past with the current buildings, which can increase people's interest and absorption of the contents, and helps them understand and be aware of Korean traditional culture and cultural heritage effectively. In addition, convergence between IT new technology, Augmented Reality(AR) and humanities through storytelling based implementation of cultural heritage in smart phone is attempted to demonstrate that there is strength in which augmented reality technique exerts infinite creativity based on actual reality world.