• Tribology and Lubricants
• /
• v.19 no.2
• /
• pp.78-84
• /
• 2003

The SCM420 used mainly to automobile transmission gear has problems that it costs transmission gear maker much money in carburising treatment. For this, it needs to alternate the existing material and heat treatment to new gear material and surface modification. For this, friction and wear experiment according to sliding speed and applied load was carried out to evaluate the wear resistance of two transmission gear materials with carburising SCM420 and nitrocarburising NT100, The presumed wear volume was calculated with the image processing for evaluation of wear resistance of two transmission gear materials. The results show that nitrocarburising NT100 has a distinguished wear resistance than carburising SCM420.

• Tribology and Lubricants
• /
• v.21 no.2
• /
• pp.93-99
• /
• 2005

The fault of an automobile transmission gear occurs whenever moving tooth surfaces interact. Such a failure condition has an effect on the frictional factors such as applied load, sliding speed, frictional time and gear oil. However, it is difficult to know the mutual relation of these factors. In this study, the friction and wear tests were carried out to get the friction characteristics with carburized SCM420 and nitrocarburized NT100 have being used as automobile transmission gear materials. And it was undertaken to analyze the frictional factors that have effect on frictional characteristics by using design of experiment. From this study, the result showed that the applied load in frictional factors was the most important, next to frictional time, sliding speed. And the friction characteristics of nitrocarburized NT100 was more excellent than carburized SCM420.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.2
• /
• pp.213-219
• /
• 2012

In this paper, we suggested the method of signal integrity for noises and distortion signal generated between high speed information transmission modules by external effects. Suggested method for signal integrity of impedance matching to remove transmission line distortion, We divided the impedance matching between the transmitter and the receiver module with the single line and differential line methods after confirmed the improvement of signal distortions through ADS simulation. the experimental results indicated that it is possible to keep signal integrity without signal distortions by matching the optimal termination impedance which are considering the signal delay of transmission line for using the high-performance modules.

• The KIPS Transactions:PartC
• /
• v.12C no.2 s.98
• /
• pp.223-228
• /
• 2005

The existing mobile communication system called DS/CDMA system, which is serviced widely nowadays, has some problems such as the severe ISI and multiple access interferences under the multi-path fading channel when applied to high-speed data transmission like multimedia transmission. To compensate these problems, we propose a sub-code multi-code hybrid DS/FH (Frequency Hopping) SS (Spread Spectrum) System by combining the multi-code system that restrains the multiple access interference with the hybrid DS/FH SS technique that reduces ISI(Intersymbol Interference) effect for high-speed transmission. Moreover, we implement and propose the sub-code technique to remedy the problems of the generic multi-code system. To verify the performance of the proposed system, the computer simulations are executed under the various channel environments.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.5
• /
• pp.189-197
• /
• 2004

The thermal rating of an overhead conductor, which is the maximum allowable current, is generally calculated on the basis of heat balance equation found in IEEE P738 standard. This is given as a function of the weather conditions such as air temperature, wind speed, wind direction, and sun heat. Wind speed among such weather parameters is strongly affected on determining the line rating when it appears very low level. Therefore there may occur inaccuracy since most anemometers used in line rating monitor systems may show low resolutions and stall speed performance. In this paper, we introduce a new methodology for determining the dynamic line rating in overhead transmission lines, without using my anemometer. It was shown that wind speed can be estimated by the temperatures of 2 indirect conductors, and through experimental study, the dynamic line rating obtained by the estimated wind speed was very closely that of weather model.

• The Journal of Information Technology
• /
• v.5 no.2
• /
• pp.47-54
• /
• 2002

OFDM ambient noise and entrain error that this research proposes in IEEE 802.11g, use 256-State 2/3 binary scale Convoulutional 8-PSK Modulations, FEC coding, PBCC and did speed of 12 Mbpses that belong on category of 5 GHzs Band FHSS way so that can be applied in 20 Mbpses DSSS'S generalization that is establishing Pyojunan in current IEEE embodying transmission device model who operate with the equal speed from 2.4 GHzs ISM Band important duty to DSSS way.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.895-902
• /
• 2015

In this paper, finite element analysis of a cycloidal pitch reducer for a 2 MW-class wind turbine is reviewed. The system is composed of one cycloid set, one spur gear set, an input shaft, an output shaft, and a housing. The system was also evaluated for stability by analyzing spur gear strength according to ISO 6336. An analysis of the natural vibration characteristics of the 2 MW-class wind turbine cycloid pitch reducer was performed with attention to critical speed with input mass unbalance, output mass unbalance, spur gear transmission error, cycloid gear transmission error, and excitation frequency.

• Journal of Drive and Control
• /
• v.19 no.4
• /
• pp.1-9
• /
• 2022

The structure and operating principle of the 2-speed shift reducer were explained, the allowable bending stress value of the material was compared with the analysis result through FM structural analysis program, and the average stress distribution value of von Mises was performed on the gear root atmosphere. The structural safety of the 2-speed planetary gear reducer was verified through FM structural analysis. The natural frequency was calculated by applying the specifications of the planetary gears of the 2-speed gearbox, and the critical speed of resonance was calculated by calculating the natural frequency and the transmission error of the engaged gear pair. As a result of analyzing the critical speed, since it is formed higher than the actual operating speed range, it is considered safe because there is no resonance problem due to the suggested specifications of the planetary gears of the 2-speed shift reduction.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.131-132
• /
• 2008

It is necessary to develop a high-speed wireless transmission system, which is able to send medical informations to the emergency medical center during emergency patient transportation. In this research, a system which transmits patient’s vital signs and a real-time audio/video contents of the event has been designed, developed, and the suitability of the system has been verified. Test results indicate that the system is capable of transmitting vital signal data, including 17 numeric data, 12 waveforms and 113 events, reading the affected part by forwarding a $320{\times}240$ pixel image at 2fps. Also, the full-duplex voice transmission of the system at 8bit/64kbps is enough to make stable communication between emergency medical technicians and hospital professionals possible. After numerous hours of driving, the packet loss of patient vital signs is 0.013%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.3
• /
• pp.106-116
• /
• 1997

In this paper, using MATLAB SIMULINK, a generalized design methodology was suggested for multi pass transmission(MPT) by classifying the vehicle power train as prime mover, MPT and vehicle dynamics. This approach enables a designer to investigate the influence of each transmission component by simple combination of system components without changes of overall program. Using the design methodology, a MPT consisting of CVT, 2, clutches and reduction gears was designed for a braking energy regenerative flywheel hybrid vehicle. The CVT is essential in order to connect the engine and flywheel speed with the vehicle speed. For the purpose of smooth clutch operation, control algorithm was suggested by introducing dead zone for the clutch engagement. Using the SIMULINK model, performance of the flywheel hybrid vehicle with MPT was investigated. It was observed from the simulation results that the MPT vehicle showed better fuel economy, 47% than that of AT vehicle, 27% than that of CVT vehicle for ECE-15 driving cycle. Especially destinct fuel efficiency improvement was obtained for city driving cycle requiring more frequent stop and start.