• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2001.10a
• /
• pp.21-24
• /
• 2001

This study is concerned with the development of efficient p-median approach to nondegenerate cell formation(CF) in group technology(GT) manufacturing. Unlike most of existing CF methodologies allowing degenerate cells or families that contains no parts or machines, this study attempts to find cell configuration where each machine cell contains at least two or more machines processing at least two or more parts so as to fully utilize the similarity in designing and processing parts. Nondegenerate CF seeks to minimize both the exceptional elements outside the diagonal block and the voids within the diagonal block. To find nondegenerate cells, a two-phase p-median methodology is proposed. In phase 1, the classical p-median model is implemented to find initial cells. In phase 2, bottleneck machines and parts are reassigned until no further degenerate cells and families are found. Test results on moderately medium-sized CF problems show the substantial efficiency of the proposed approach.

• Journal of Institute of Convergence Technology
• /
• v.2 no.2
• /
• pp.30-34
• /
• 2012

The SI thermochemical cycle process accomplishes water splitting through distinctive three chemical reactions. We focused on thermodynamic models applicable to the process. Recently, remarkable models based on the assumed ionic species have been developed to describe highly nonideal behavior on the liquid phase reactions. ElecNRTL models with ionic reactions were proposed in order to provide reliable process simulation results for phase equilibrium calculations in Section II and III. In this study, the current thermodynamic models of SI thermochemical cycle process were briefly described and the calculation results of the applied ElecNRTL models for phase equilibrium calculations were illustrated for binary systems.

• New & Renewable Energy
• /
• v.3 no.2 s.10
• /
• pp.47-52
• /
• 2007

Hydrate phase equilibrium for the binary $CO_{2}$+water and $CH_{4}$+water mixtures in silica gel pore of nominal 6, 30, and 100 nm were measured and compared with the cacluated results based on van der Waals and Platteeuw model. At a specific temperature three-phase hydrate-water-vapor (HLV) equilibrium curves for pore hydrates were shifted to the higher-pressure condition depending on pore sizes when compared with those of bulk hydrates. Notably, hydrate phase equilibria for the case of 100 nominal nm pore size were nearly identical with those of bulk hydrates. The activities of water in porous silica gels were modified to account for capillary effect, and the calculation results were generally in good agreement with the experimental data.

• Journal of Magnetics
• /
• v.18 no.2
• /
• pp.117-124
• /
• 2013

Single-phase, brushless DC (BLDC) motors have unequal air-gaps to eliminate the dead-point where the developed torque is zero. Unfortunately, these unequal air-gaps can deteriorate the motor characteristics in the cogging torque. This paper proposes a novel design for a single-phase BLDC motor with an asymmetric notch to solve this problem. In the design method, the asymmetric notches were placed on the stator pole face, which affects the change in permanent magnet shape or the residual flux density of the permanent magnet. Parametric analysis was performed to determine the optimal size and position of the asymmetric notch to reduce the cogging torque. Finite element analysis (FEA) was used to calculate the cogging torque. A more than 28% lower cogging torque compared to the initial model with no notch was achieved.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.11 no.6
• /
• pp.824-834
• /
• 1999

Characteristics of two-phase flow and heat transfer were numerically investigated in a submerged gas injection system when temperature of the injected gas was different from that of the liquid. The Eulerian approach was used for both the continuous and dispersed phases. The turbulence in the liquid phase was modeled using the standard $k-\varepsilon$$\varepsilon$ turbulence model. The interphase friction and heat transfer coefficient were calculated from the correlations available in the literature. The turbulent dispersion of the phases was modeled by a "dispersion Prandtl number". In the case with heat transfer where the temperature of the injected gas is higher than the mean liquid temperature, the axial and the radial velocities are lower in comparison with the case of homogeneous temperatures. The results in the present research are of interest in the design and operation of a wide variety of material and chemical processes.

• Journal of Korean Institute of Industrial Engineers
• /
• v.26 no.4
• /
• pp.296-305
• /
• 2000

Virtual wavelength path (VWP) is the optical path when a wavelength conversion is possible in a wavelength division multiplexing (WDM) network that is transmission infrastructure for the next generation high speed backbone networks. To achieve efficient design for VWP networks, we must consider VWP routing, wavelength assignment, and wavelength conversion while satisfying many technical constraints of the WDM networks. In this study we propose an integrated model for efficient VWP design in WDM networks. We also develope a 3-phase algorithm, each of which deals with routing, wavelength assignment and route and wavelength reassignment, respectively. In our computational experiments, phase 1 algorithm can solve the problem to the optimality for medium size test networks. Phase 2 algorithm is an efficient heuristic based on a reduced layered network and can give us an effective wavelength assignment. Finally, phase 3 algorithm reconfigure VWP routing and its wavelength assignment to concentrate wavelength conversion nodes in the suggested VWP network.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.591-601
• /
• 2019

With the development of renewable energy, grid-connected inverter technology has become an important research area. When compared with traditional silicon IGBT power devices, the silicon carbide (SiC) MOSFET shows obvious advantages in terms of its high-power density, low power loss and high-efficiency power supply system. It is suggested that this technology is highly suitable for three-phase AC motors, renewable energy vehicles, aerospace and military power supplies, etc. This paper focuses on the SiC MOSFET behaviors that concern the parasitic component influence throughout the whole working process, which is based on a three-phase grid-connected inverter. A high-speed model of power switch devices is built and theoretically analyzed. Then the power loss is determined through experimental validation.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.8
• /
• pp.4641-4646
• /
• 2013

Objective: To explore clinical experience and propose new ideas for treating children diagnosed with orbital rhabdomyosarcoma (RMS). Methods: We retrospectively analyzed the clinical data for30 patients (16 males and 14 females, with a median age of 6.2 years) with primary orbital RMS who were enrolled in the Department of Eye Oncology and Pediatrics of our hospital from November 2004 to December 2012. International Rhabdomyosarcoma Organization Staging Standards indicated that among the 30 patients, 4 cases were in phase II, 20 were in phase III, and 6 were in phase IV. All patients underwent a multidisciplinary collaborative model of comprehensive treatment (surgery, chemotherapy, external radiotherapy, $^{125}I$ radioactive particle implantation, and autologous peripheral blood stem-cell transplantation). Results: Follow-up was conducted until March 2013, with a median follow-up time of 47.2 months (5 to 95 months), and 7 deaths occurred. The 2-year estimated survival rate reached 86.1%, the ${\geq}3$-year estimated survival rate was 77%, and the 5-year estimated survival rate was 70.6%. Conclusions: The multidisciplinary collaborative model can be a safe and effective approach to the comprehensive treatment of children with orbital RMS. It has clinical significance in improving the tumor remission rate.

• Nuclear Engineering and Technology
• /
• v.40 no.2
• /
• pp.133-138
• /
• 2008

The use of Supercritical Fluids(SCF) has been proposed for numerous power cycle designs as part of the Generation IV advanced reactor designs, and can provide for higher thermal efficiency. One particular area of interest involves the behavior of SCF during a blowdown or depressurization process. Currently, no data are available in the open literature at supercritical conditions to characterize this phenomenon. A preliminary computational analysis, using a homogeneous equilibrium model when a second phase appears in the process, has shown the complexity of behavior that can occur. Depending on the initial thermodynamic state of the SCF, critical flow phenomena can be characterized in three different ways; the flow can remain in single phase(high temperature), a second phase can appear through vaporization(high pressure low temperature) or condensation(high pressure, intermediate temperature). An experimental facility has been built at the University of Wisconsin to study SCF depressurization through several diameter breaks. The preliminary results obtained show that the experimental data can be predicted with good agreement by the model for all the different initial conditions.

• Transactions of Materials Processing
• /
• v.11 no.5
• /
• pp.447-456
• /
• 2002

A study has been made to investigate the boundary sliding and its accommodation mode with respect to the variation of $\alpha$$_2$/$eta$ volume fraction during superplastic deformation of two-phase Ti$_3$Al-xNb intermetallics. Step strain rate and load relaxation tests have been performed at 950, 970 and 99$0^{\circ}C$ to obtain the flow stress curves and to analyze the deformation characteristics by the theory of inelastic deformation. The results show that the grain matrix deformation and boundary sliding of the three intermetallics containing 21, 50 and 77% in $eta$ volume fractions are well described by the plastic deformation and viscous flow equations. Due to the equal accommodation of both $a^2$ and $\beta$ phases, the accommodation modes for fine-grained materials are in good agreement with the iso-strain rate models. The sliding resistance analyzed for the different boundaries is the lowest in the $\alpha$$_2$/$\alpha$$_2$ boundary, and increases in the order of $\alpha$$_2$/$\alpha$$_2$<< $\alpha$$_2$/$\beta$ = $\beta$/$\beta$, which plays an important role in controlling the superplasticity of the alloys with the various $\alpha$$_2$/$\beta$ phase ratio.