• Journal of the Society of Disaster Information
• /
• v.13 no.3
• /
• pp.296-304
• /
• 2017

In order to predict about forest fire behavior we constructed a database for combustion characteristic of forest fuels in Samcheok, Gangwon-do and prepared fire risk map and fire risk rating using GIS method in this study. For the mapping autoignition temperature, ignition time, flame duration time, total heat release and total smoke release are selected as the standardized parameters and the overall risk rating was made up of the ignition risk parameters(autoignition temperature, ignition time) and the spread risk parameters(flame duration time, total heat release, total smoke release). Forest fire risk was classified into 5 grades and lower grade of fire risk rating mean to correspond to more dangerous forest fire. As a result, the overall risk rating of Samcheok was classified into three grades from 1 to 3 and Nogok-myeon and Miro-myeon were turned out the most dangerous areas for forest fire. Because of the colony of pine and oak trees and the higher fire loads, the flame propagation will be carried out quickly in these areas.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.3
• /
• pp.679-685
• /
• 2004

Although the electrophoretic deposition method has the advantage of simple processing procedure, less fabrication facilities, and easier control for deposition thickness and wire length, providing economical and technical merits, it also has the disadvantages of cracking and porosity phenomena, requiring an improved processing method for higher particle density and constant particle orientation. we have developed an optimization method to increase the particle density and to unify its orientation, and have performed a study to overcome the cracking and porosity problems in the fabricated superconductor. In order to improve the surface uniformity and the conduction properties of the fabricated YBCO thick films, a system that applies alternate voltage vertically has been developed for the first time and applied to the electrophoretic deposition process. The applied alternate electric field caused a force to be exerted on each YBCO particle and resulted in a rotation of the particle in the direction of applied electric field, accomplishing a uniform particle orientation. We name this process as the shaky-aligned electrophoretic deposition method. For commercial utilization and efficiency, in this dissertation, alternating voltage of 60 Hz and 25 ∼ 120 V/cm was proposed to apply it as a subsidiary source for shaky-flow deposition so that the fabricated thin film showed uniform surface morphology with less voids and cracks and Tc,zero of 90 K and the critical current density of 3419 A/$cm^2$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.709-716
• /
• 2016

Recently, the operating conditions of the various mechanical structures have become more severe and the running time has become longer as the development of plant equipment increases with the introduction of high technology. Thus, the reliability of the system and its accessories is becoming a problem. Normally, synthetic natural gas (SNG) plants use 1.25Cr-0.5Mo or 2.25Cr-1Mo heat resistant steel according to the operating conditions. In this study, a lab-scale reactor was set up using 1.25Cr-0.5Mo steel, in order to carry out corrosion tests for producing synthetic natural gas. The corrosive characteristics were investigated under 1st-methanator operating conditions and fundamental data about the durability and reliability were obtained by using the experimental test. The analysis of results obtained on the durability of the reactor under emission and injection compositions showed that the hydrogen embrittlement caused by hydrogen and the oxidation corrosion caused by H2O had the most effect on the durability of 1.25Cr-0.5Mo steel in the SNG reactor. However, the hydrogen embrittlement and oxidation corrosion occurred simultaneously under emission conditions, so that the corrosion of the material increased suddenly after a long operating time. Besides, the corrosion of the 1.25Cr-0.5Mo steel under the injection composition was faster than that under the emission composition.

• Journal of KIISE:Information Networking
• /
• v.37 no.5
• /
• pp.374-385
• /
• 2010

Wireless mesh networks can be deployed for various networks from home networking to last-mile broadband Internet access. Wireless mesh networks are composed of mesh routers and mesh clients. In these networks, static nodes form a multi-hop backbone of a large wireless access network that provides connectivity to end-users' mobile terminals. The network nodes cooperate with each other to relay data traffic to its destinations. In order to increase connectivity and better performance, researchers are getting interested in multi-channel and multi-interface wireless mesh networks. In these networks, non-overlapping multiple frequency channels are used simultaneously to increase the aggregate bandwidth available to end-users. Recently, researches have focused on finding suitable channel assignments for wireless network interfaces, equiped in a mesh node, together with efficient routing to improve overall system throughput in wireless mesh networks. This goal can be achieved by minimize channel interference. Less interference among using channels in a network guarantees more aggregated channel capacity and better connectivity of the networks. In this thesis, we propose interference aware channel assignment and routing algorithms for multi-channel multi-hop wireless mesh networks. We propose Channel Assignment and Routing algorithms using Traffic Profiles(CARTP) and Routing algorithms allowing detour routing(CARTP+2). Finally, we evaluate the performance of proposed algorithms in comparison to results from previous methods using ns-2 simulations. The simulation results show that our proposed algorithms can enhance the overall network performance in wireless mesh networks.

• Smart Media Journal
• /
• v.6 no.3
• /
• pp.89-94
• /
• 2017

The existing geofences provide only context-awareness service for entering or leaving the set region when a user sets a virtual region for his/her PoI(Point of Interest). Applying the mobile-geofence technology to the connected car technology, which is attracting attention as a next generation technology, it is possible to provide application service without additional infrastructure construction cost However, to do this, we need to expand and improve the functions of traditional geofence. In this paper, we propose and implement a flexible mobile-geofence in which the radii of each geofence applied to vehicles is changed according to context-aware in order to support connected cars technology based on the previously studied mobile three-dimensional geofence system. The proposed flexible mobile-geofence shows experimentally that the region of the geofence is changed according to context-aware of itself and its surroundings after applying a flexible decision algorithm by the flexible factor analysis. In the future, we are expected that the flexible mobile-geofence proposed in this paper will be applied not only to connected-cars technology but also to the application technology of V2X(Vehicle to Everything) for safe and efficient vehicle operation.

• Journal of the Korean Institute of Gas
• /
• v.17 no.5
• /
• pp.64-68
• /
• 2013

Non destructive testing(NDT) methods of electrofusion(EF) joints of thermoplastics pipes are required for fusion joint safety and for the long term reliability of a pipe system. Electrofusion joints, which are joined at the proper fusion process and procedures, may encounter defects due to the difference of ovality between pipes and coupling, improper fusion process or porosity result from electrofusion joining. These defects can cause the failure of pipeline and by extension, they can be caused the limit to expand the use of plastics pipes. This paper studies inspection results using ultrasonic imaging method for damaged polyethylene electrofusion joints. Gas was leaking from 250mm diameter polyethylene electrofusion joints at February 2004 which was electrofused at December 1994 and operation pressure was 2.45kPa. First, surface inspection was conducted and then in order to find the types of defects examination using ultrasonic imaging method was performed. Lack of fusion and inappropriate inserting for polyethylene pipes into electrofusion coupling were found and causes of the gas leak were judged that misalignment and insert defect. Cutting inspection was performed and each inspection results were compared to. Results of ultrasonic imaging method and cutting inspection were the same.

• Journal of Korean Society on Water Environment
• /
• v.23 no.2
• /
• pp.260-265
• /
• 2007

This study was carried out to complement water quality standards and to establish new concept for water quality standards reflecting current state of water quality in small streams. By this purpose, discriminant analysis was performed and Water Quality Level Model (WQLM) was developed using the data such as EC, BOD, $COD_{Mn}$, SS, T-N, T-P, $NH_3-N$ in 224 agricultural streams. To give water quality level for water quality parameters, it divided into 20% respectively in the order of excellent water quality. On the basis of the lowest water quality level, water quality level of small streams is granted. As a result of it, number of stream corresponding to Level I was no, Level II was 2 streams, Level III was 22 streams, Level IV was 70 streams, and Level V was 130 streams. Average of water quality in each level was the highest in Level V. EC, SS, and T-N of 7 parameters were selected in variance concerned water quality level. By standardized canonical discriminant function coefficient, EC of three variances was the highest in 0.625 at the discriminant power. The next was T-N (0.509), SS (0.414). By discriminant function for water quality level, Level II was equal to $-2.973+19.376{\times}(EC)+0.647{\times}(T-N)+0.009{\times}(SS)$, Level III was equal to $-3.288+19.190{\times}(EC)+0.733{\times}(T-N)+0.041{\times}(SS)$, Level IV was equal to $-4.462+27.097{\times}(EC)+0.792{\times}(T-N)+0.053{\times}(SS)$, and Level V was equal to $-9.117+40.040{\times}(EC)+1.305{\times}(T-N)+0.111{\times}(SS)$. As a result of test at real agricultural watershed of Jeongan and Euidang in Gongju city, the fitness of WQLM was high to 88.78%. But, to get accomplished water quality assessment more exactly in agricultural streams, we had to concentrate and get vast data, and WQLM was modified and complemented continually.

• Korean Journal of Food Science and Technology
• /
• v.32 no.2
• /
• pp.349-355
• /
• 2000

This study was conducted to enhance the storage stability of fermented shrimp with different salt contents using a high hydrostatic pressure. The effects of the magnitude of pressure and treatment time on the microorganisms of the fermented shrimp were investigated. The highest microbial counts with respect to the salt levels were observed at 18% salt, showing $3.4{\times}10^5\;CFU/g$ for general bacteria, $6.4{\times}10^4\;CFU/g$ for halophilic bacteria, $4.2{\times}10^5\;CFU/g$ for yeast and $3.0{\times}10^4\;CFU/g$ for halophilic yeast. The degree of sterilization increased with the magnitude of pressure and treatment time, and the sterilization could be analyzed by the first order reaction kinetics. The sterilization rate constants $(k_p)$ of the halophilic bacteria was lower than that of general bacteria. The $log(k_p)$ increased linearly with pressure and the slope of the regression line of the halophilic bacteria was greater than that of general bacteria, indicating that the sterilization of the halophilic bacteria was more dependent on the pressure. High hydrostatic pressure treatment was an effective non-thermal sterilization method for the salted and fermented shrimp, and the optimum treatment condition was for 10 min at 6,500 atm.

• Journal of dental hygiene science
• /
• v.15 no.2
• /
• pp.182-189
• /
• 2015

The purpose of this study was to investigate the relationship between degree of satisfaction and experience on performance in accordance with the characteristics for the dental hygiene students. Dental hygiene students to 480 people from November to December 2014 and analyzed by conducting a survey. The higher grade students were more satisfied with the degree of satisfaction on experience for clinical test performance and clinical practice organization rather than the lower grade students. Also, the degree of satisfaction on major for the higher grade students has been shown as relatively higher than the lower grade students. The factors that affecting the experience for clinical performance and the degree of satisfaction for clinical practice were shown as grade, satisfaction for major and period for practice. In order to enhance the degree of satisfaction on the clinical performance for students, it should be established the system for practice management considering the characteristics of clinical practice by relevant organizations. Also, the dental hygienist who is responsible for dental education should manage his/her practice for students actively. Meanwhile, the practice organization should improve and update the content of education through the consistent alliance with colleges continuously.

• 재활복지
• /
• v.21 no.2
• /
• pp.1-27
• /
• 2017

The purpose of this study is to evaluate the level of implementation of the Incheon Strategy and to develop measures for effective implementation. This research method used literature review and monitoring method. The results of the study are summarized as follows: First, 9 key indicators and 7 supplementary indicators, which are classified into implementation and non-implementation, 3 key indicators have been implemented, one indicator has been partially implemented, 5 indicators have not yet been implemented, Also, In the case of supplementary indicators, five were implemented and two were not. Second, the ten target areas are lacking in implementation, but the objective of 7 is to ensure the comprehensive disaster risk reduction and management, the ratification and implementation of the Convention on the Rights of Persons with Disabilities and the harmonization of the Convention with the domestic law, Also, it is analyzed that the level of implementation is in the order of improving the reliability and comparability of the data of goal 8, ensuring gender equality of goal 6 and strengthening the capacity of women. Based on these results, we propose an improvement plan for implementation. First, it is necessary to formulate policy issues and implement measures for the implementation of Incheon Strategy. Second, it is necessary to establish a system to implement and monitor for Incheon strategy. Third, Korean standards for goals and targets, key indicators and supplementary indicators are needed. Fourth, it is necessary to prioritize the target implementation and to take preemptive action. Lastly, it is necessary to educate and publicize for the Incheon strategy.