• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2012.10a
• /
• pp.276-277
• /
• 2012

This study was carried out in the laboratory of the reverberation. A total of six specimens were fabricated depending on the thickness and strength. Floor impact sound insulation performance was measured in 1/3 octave band center frequency. The results of this study are as follows. Although some differences in the frequency band, the result of evaluating the weight impact sound blocking performance as the thickness increases, the floor impact sound insulation performance is improved. In addition, to increase the strength of the slab, even if the block impact sound performance is improved.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11b
• /
• pp.1104-1108
• /
• 2001

It is a difficult and important task to measure the reverberation time of an acoustic room with a short reverberation time. This paper presents a new technique to measure the reverberation time of an acoustic room with low value of BT60. The digital signal processing technique used to do this is the wavelet filter which is very flexible to design the 1/n octave band filter and has no delay problem compared with the conventional IIR digital filter. This method is successfully applied to the measurement of the reverberation time at low frequency band of famous concert halls in Korea.

• Journal of KSNVE
• /
• v.7 no.1
• /
• pp.71-79
• /
• 1997

The objective of this study is to investigate experimentally the effect of surface conditions of the plate on the impinging jet noise. The experimental results about the spectrum, the sound pressure level and the directivity are pressented and discussed in relation with the surface conditions. Regardless of the surface conditions, the pure tones of high level are generated at the same frequency band and the overall sound power level of impinging jets is much higher than that of the free jet. However, the velocity dependence of the sound pressure level and the directivity are different between smooth surfaces and rough surfaces. The dependence of sound pressure level on the jet velocity shows that the smooth surface generates quadrupole-type sound like free jets. However, the perforated or the rough surface radiates sound power exactly proportional to the sixth power of the jet velocity, indicating that the source is fixed dipole type. The directivities of 1/3 octave band sound pressure level for both the free and impinging jet show the peak directivity at 115$^\circ$ upstream, probably due to the refraction associated with velocity gradient.

• Proceedings of the Korean Society of Computer Information Conference
• /
• 2014.01a
• /
• pp.425-426
• /
• 2014

충격소음(Impulse Noise) 측정 시 지그(Ear Simulator)가 자체적으로 음압측정에 미치는 영향을 확인하기 위해 지그를 이용하여 실내에서 충격소음을 측정하였다. 측정의 신뢰성과 정확성을 확보하기 위해 마이크로폰과 지그에서 동일조건에서 동시에 데이터를 수집하였다. 추가로 헤드&토르소에서 실험을 실시하였다. 최대음압레벨과 1/3옥타브 밴드 결과를 비교분석함으로써 측정 방법에 따른 차이점을 발견하였다.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.2
• /
• pp.83-89
• /
• 1996

The objective of this study is to find experimentally the characteristics of the noise generated by the impinging jet on the normal plate, and also to compare the noise characteristics of the impinging jet with those of the free jet. The experiment is performed for the measurement of the noise specturm, the noise power, and the directivity for the free and impinging jets. From the experiment. it is found that the power of noises generated by the free jet as well as the impinging jet is proportional to the eighth power of the jet velocity through the circular converging nozzle, and that the noise power of the impinging jet is 15dB as high as one of the free jet when the plate distance is about within one to three times the nozzle diameter at the pressure ratio 1.39. The sound pressure level of the impinging jet depends upon the jet pressure and the plate distance. The plate distance with the maximum overall sound pressure level is increased with the jet pressure. The directivities with 1/3 octave band frequency for both the free jet and the impinging jet are greatly influenced by the convection effect.

• The Journal of the Acoustical Society of Korea
• /
• v.22 no.3
• /
• pp.233-241
• /
• 2003

It is statistically analyzed the underwater ambient noise measured at 13 sites less than 200 m deep in the shallow water surrounding the Korean Peninsula for 9 yews from 1990 to 1998 in various environmental conditions. Frequency spectra were obtained with the 1/3-octave band center frequencies from 25㎐ to 20 ㎑. The analyzed shallow water noise spectra were some different from the deep water blown as the Wenz spectra. We could know that the ambient noise level shows higher than it in same condition by effect of various ship activity and the coastal noise, surface waves, and so on. As a result, we produced the coastal ambient noise spectra curve based on these results in shore of the Korea Peninsula.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.857-860
• /
• 2003

We introduced the basic direction of revision for KS F 2805 (method for measurement of sound absorption coefficient in a reverberation room). It is fundamentally equal to ISO 354 (measurement of sound absorption in a reverberation room) which was state of ISO/FDIS 354. Two main points were strongly reviewed. First, the sound absorption coefficient values for Type J test specimen mounting was investigated. Next, the reverberation time difference between the conventional method and new additional one, impulse response method were compared.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.1
• /
• pp.20-28
• /
• 1989

SEA(Statistical Energy Analysis) method has been applied to predict the sound radiation power from vibrating machinery. In this study, sound radiation power was predicted from coupled structures by transmission of vibration, which composed of two plates welded into an L shape. The predicted sound radiation power is in agreement within 2 or 3 dB on octave band comparing with values obtained from direct measurements. Also, in order to prove the validity of this method in changes of sound radiation power associated with modifications to structures, rubber pad was stuck on a plate. The results agree approximately within 3 or 5 dB. And SEA method is valuable for the optimal design to reduce the noise. Additionally, this paper suggests that the logarithmic decrement method is valid as the one for finding the loss factor.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.379-383
• /
• 2000

This paper describes the design program of duct silencer. Duct silencer is used ventilating system. Variables in the program for predicting transmission loss are width of splitter, airway width, perforate plate, absorption material and frequency. Generally used expression for predicting transmission loss has something that don't think about frequency characteristic. Therefore we propose the new expression that considered frequency characteristic. In the 1/1 octave band center frequency, the expected weighting number(K) is fitted with absorption ratio and airway width. The fitted 2nd degree polynomial expression is based on the test data performed in YOUIL Industrial Corperation. This program's accuracy is about 90 percent.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.8 no.1
• /
• pp.1-6
• /
• 1975

The sea noise of moving trawl net was recorded by an underwater tape recorder which was set wireless, and was analyzed by a sound level meter and an octave-band analyzer. The frequency distribution of sea noise of the moving otter trawl net ranged from DC to 5000 Hz, and the dominant frequency zone ranged from 500 Hz to 700 Hz, and the maximum sound pressure is about 22 dB at the otter trawl net. The main sound source of the sea noise from the moving trawl net was found to be sea noise due to the resistance of the ground rope against the sea bottom.