Proceedings of the Korean Society of Machine Tool Engineers Conference
/
2002.10a
/
pp.192-197
/
2002
In this study, examined the cutting characteristics of alumuminum alloy AC8A-T6 that is used to present car piston materials. And in been holding materials machining empirically escape as result that experiment comparison changing the cutting speed and feed on various condition to choose efficient machining condition. The following results can be summarized from this research. 1. As the cutting speed decreased, principal cutting force and thrust cutting force is increased, and reason that cutting force interacts greatly in the low cutting speed is thought by result by BUE's stabilization. 2. The feed speed and cutting speed increase, friction factor is decrescent and the cause appeared the thrust cutting force is fallen than cutting force relatively because chip flow according to increase of the feed rate is constraint. 3. Though specific cutting resistance grows cutting area and the feed rate are few, the cause was expose that shear angle decreases by rake face of tool gets into negative angle remarkably as wear of a cutting tool or defect part of workpiece is cut. 4. Cutting speed do greatly depth of cut is slow, surface roughness examined closely through an experiment that becomes bad, and know that it can get good surface that process cutting speed because do feed rate by 0.1mm/rev low more than 250m/min to get good surface roughness can.
The Journal of Korean Institute of Communications and Information Sciences
/
v.30
no.3A
/
pp.217-225
/
2005
This paper presents specialized DSP instructions and their architecture for the Viterbi algorithm used in various wireless communication standards. The proposed architecture can significantly reduce the Trace Back (TB) latency. The proposed instructions perform the Add Compare Select (ACS) and TB operations in parallel and the architecture has special hardware, called the Offset Calculation Unit (OCU), which automatically calculates data addresses for the trellis butterfly computations. Logic synthesis has been Performed using the Samsung SEC 0.18 μm standard cell library. OCU consists of 1,460 gates and the maximum delay of OCU is about 5.75 ns. The BER performance of the ACS-TB parallel method increases about 0.00022dB at 6dB Eb/No compared with the typical TB method, which is negligible. When the constraint length K is 5, the proposed DSP architecture can reduce the decoding cycles about 17% compared with the Carmel DSP and about 45% compared with 7MS320c15x.
The Journal of Korean Institute of Electromagnetic Engineering and Science
/
v.26
no.1
/
pp.71-80
/
2015
LDO(Low Drop-Out) regulators have become an essential building block in modern PMIC(Power Managment IC) to extend battery life of electronic devices. In this paper, we optimize capacitor-less LDO regulator via Geometric Programming(GP) designed using Dongbu HiTek $0.5{\mu}m$ BCDMOS process. GP-compatible models for stability and PSR of LDO regulators are derived based on monomial formulation of transistor characteristics. Average errors between simulation and the proposed model are 9.3 % and 13.1 %, for phase margin and PSR, respectively. Based on the proposed models, the capacitor-less LDO optimization can be performed by changing the PSR constraint of the design. The GP-compatible performance models developed in this work enables the design automation of capacitor-less LDO regulator for different design target specification.
Reverberation in speech signals tends to significantly degrade the performance of the Blind Source Separation (BSS) system. Especially in online systems, the performance degradation becomes severe. Methods based on joint diagonalizability constraints have been recently developed to tackle the problem. To improve the quality of separated speech, in this paper, we add the proposed de-reverberation method to the online BSS algorithm based on the constraints in reverberant environments. Through experiments on the WSJCAM0 corpus, the proposed method was compared with the existing online BSS algorithm. The performance evaluation by the Signal-to-Distortion Ratio and the Perceptual Evaluation of Speech Quality demonstrated that SDR improved from 1.23 dB to 3.76 dB and PESQ improved from 1.15 to 2.12 on average.
Kouame Yao;Mohammed O. Idrees;Abdul-Lateef Balogun;Mohamed Barakat A. Gibril
Economic and Environmental Geology
/
v.56
no.6
/
pp.817-830
/
2023
This study investigates the age of the surficial rocks in the Arunta region using Uranium-Lead (U-Pb) geochronological dating. Rock samples were collected at four locations, Cattle-Water Pass (CP 1610), Gough Dam (GD 1622 and GD 1610), and London-Eye (LE 1601), within the Strangways Metamorphic Complex and crushed by selFragging. Subsequently, the zircon grains were imaged using Cathodoluminescence (CL) analysis and the U-Pb (uranium and lead) isotope ratios and the chrono-stratigraphy were measured. The imaged zircon revealed an anomalous heterogeneous crystal structure. Ellipses of the samples at locations GD1601, CP1610, and GD1622 fall below the intercept indicating the ages produced discordant patterns, whereas LE1601 intersects the Concordia curve at two points, implying the occurrence of an event of significant impact. For the rock sample at CP1610, the estimated mean age is 1742.2 ± 9.2 Ma with mean squared weighted deviation (MSWD) = 0.49 and probability of equivalence of 0.90; 1748 ± 15 Ma - MSWD = 1.02 and probability of equivalence of 0.40 for GD1622; and 1784.4 ± 9.1 Ma with MSWD of 1.09 and probability of equivalence of 0.37 for LE1601. But for samples at GD1601, two different age groups with different means occurred: 1) below the global mean (1792.2 ± 32 Ma) estimated at 1738.2 ± 14 Ma with MSWD of 0.109 and probability of equivalence of 0.95 and 2) above it with mean of 1838.22 ± 14 Ma, MSWD of 1.6 and probability of equivalence of 0.95. Analysis of the zircon grains has shown a discrepancy in the age range between 1700 Ma and 1800 Ma compared to the ASO dated to have occurred between 440 and 300 Ma. Moreover, apparent similarity in age of the core and rim means that the mineral crystallized relatively quickly without significant interruptions and effect on the isotopic system. This may have constraint the timing and extent of geological events that might have affected the mineral, such as metamorphism or hydrothermal alteration.
KSII Transactions on Internet and Information Systems (TIIS)
/
v.14
no.8
/
pp.3312-3327
/
2020
Plant diseases are a significant yield and quality constraint for farmers around the world due to their severe impact on agricultural productivity. Such losses can have a substantial impact on the economy which causes a reduction in farmer's income and higher prices for consumers. Further, it may also result in a severe shortage of food ensuing violent hunger and starvation, especially, in less-developed countries where access to disease prevention methods is limited. This research presents an investigation of Directional Local Quinary Patterns (DLQP) as a feature descriptor for plants leaf disease detection and Support Vector Machine (SVM) as a classifier. The DLQP as a feature descriptor is specifically the first time being used for disease detection in horticulture. DLQP provides directional edge information attending the reference pixel with its neighboring pixel value by involving computation of their grey-level difference based on quinary value (-2, -1, 0, 1, 2) in 0°, 45°, 90°, and 135° directions of selected window of plant leaf image. To assess the robustness of DLQP as a texture descriptor we used a research-oriented Plant Village dataset of Tomato plant (3,900 leaf images) comprising of 6 diseased classes, Potato plant (1,526 leaf images) and Apple plant (2,600 leaf images) comprising of 3 diseased classes. The accuracies of 95.6%, 96.2% and 97.8% for the above-mentioned crops, respectively, were achieved which are higher in comparison with classification on the same dataset using other standard feature descriptors like Local Binary Pattern (LBP) and Local Ternary Patterns (LTP). Further, the effectiveness of the proposed method is proven by comparing it with existing algorithms for plant disease phenotyping.
To assess the adequacy of medical manpower and medical fee for the newborn nursery care, the author visited 20 out of 24 hospitals with the pediatric training program in Youngnam area between July 29 and August 14, 1991. Total number of newborn, both normal and sick, admission and discharge in 1-30 June 1991 was obtained from the logbook of nursery. Head nurse and staff pediatrician of the nursery were interviewed to get the current staffing for the nursery and their subjective opinion on the adequacy of nursery manpower and the difficulties in recruiting manpower. Average medical fee charged for the maternity and normal newborn nursery care was obtained from the division of self-audit of medical insurance claim of each hospital. Average minimum requirement of nursing care time for one normal newborn per day was 179.5 (${\pm}58.6$) minutes; 202.3(${\pm}50.7$) minutes for the university hospitals and 164.2(${\pm}60.5$) minutes for the general hospitals. The ratio of minimum requirement of nursing care time and available nursing time was 1.42 on the average. Taking the additional requirement of nursing care for the sick newborns into consideration, the ratio was 2.06. The numbers of R. N. and A. N. in the nurserys of study hospitals were 31%, and 17%, respectively, of the nursing manpower for the nursery recommended by the American Academy of Pediatrics. These findings indicate that the nursing manpower in newborn nursery is in severe shortage. Ninety percent of the head nurses and 85% of the staff pediatrician stated that the newborn nursery is short of R.N. and 75% of them said that the nurse's aide is also short. Major reason for not recruiting R.N. was the financial constraint of hospital. For the recruitment of nurse's aide, short supply was the second most important reason next to the financial constraint. However, limit of quarter in T.O. was the mar reason for the national university hospitals. Average total medical fee for the maternity and newborn nursery cares of a normal vaginal delivery who stayed two nights and three days at hospital was 219,430won. Out of the total medical fee, 20,323won(9.3%) was for the newborn nursery care. In case of C-section delivery who stayed six nights and seven days, total medical fee was 732,578won and out of the total fee 76,937won (12.0%) was for the newborn care. Cost for a newborn care per day by cost accounting was 16,141won for the tertiary care hospitals and 14,576won for the all other hopitals. The ratio of cost and the fee schedule of the medical insurance for a newborn care per day was 5.0 for the tertiary care hospitals and 4.9 for the all other hospitals. Considering the current wage level of the medical personnel, capital investment for the hospital facilities and equipments, and the cost for hospital maintenance, it is hard to expect adequate quality care in the newborn nursery under the current medical insurance fee schedule.
Journal of the Korea Academia-Industrial cooperation Society
/
v.11
no.6
/
pp.2118-2123
/
2010
Korean individual occupational exposure control is focused on the retrospective service to the over-exposed person by the reading of personal dosimeter. Since the radiophamaceuticals using in the nuclear medicine department are uncontained radiation sources, the potential exposure at working environment is very high. Moreover, a patient remains radioactive for hours or even days after the administration of a radiopharmaceutical for diagnosis or treatment. Thus, the proper working environmental exposure control must be established and executed to protect not only the affiliated employees, but also guardians accompanying patients and temporarily visiting public from the exposure by the patients. Japanese radiation protection law regulates working environmental radiation exposure by regularly measuring and filing the environmental dose for years. This study was aimed at measuring working environmental radiation dose in the nuclear medicine department of an university hospital located in Daejeon, Korea. We measured the accumulation radiation dose in air at 8 locations in the nuclear medicine department by using the same method as in Japan with glass dosimeters. The highest dose rate, 0.23 mSv per month, was measured at the waiting room, and the second one is at reception desk. Even though the doses were lower than the Korean constraint dose rate (0.3 mSv/week) at the boundary of the radiation controlled area, it was over the dose limit of public (1 mSv/y) and environment (0.25 mSv/y). Conclusionally, it was found that the new or additional procedure was necessary to less the exposure dose to the receptionist and guardians by the environmental radiation dose in the nuclear medicine department.
Journal of rehabilitation welfare engineering & assistive technology
/
v.10
no.3
/
pp.207-214
/
2016
The aim of this study was to evaluate Influence on intra-limb coordination in individuals wearing knee brace during walking. Seven healthy male adults ($32.3{\pm}2.7$ years old, $175.2{\pm}3.8cm$, $76.2{\pm}8.7kg$) participated. They wore knee brace or didn't wear any knee brace and were asked to walk along a 10 m long walkway. Spatiotemporal parameters, angles of the lower limbs, and intra-limb continuous relative phase (CRP) were measured and calculated. No differences of spatiotemporal parameters were shown (all p > 0.05). There were no changes in the angle and its range of motion (ROM) in the hip for the subjects as wearing knee brace, while ROM ($65.5{\pm}3.7^{\circ}$ vs. $60.5{\pm}3.5^{\circ}$, p < 0.05) of the angle and maximum flexion angles (stance: $31.9{\pm}4.6$ vs. $25.6{\pm}5.5$, swing: $76.7{\pm}3.1$ vs. $68.9{\pm}3.4$, all p < 0.05) in the knee significantly decreased. No changes in ROM of angle in the ankle were shown, whereas maximum dorsiflexion decreased ($22.4{\pm}2.6$ vs. $19.2{\pm}2.1$, p < 0.05) and maximum plantarflexion increased ($9.5{\pm}3.0$ vs. $15.7{\pm}2.2$, p<0.05). There were no changes in most of CRP between joints. CRP between the hip and knee joints decreased ($93.0{\pm}7.8$ vs, $84.7{\pm}4.9$, p < 0.05). Most of CRP standard deviation increased (between the hip and ankle joint during swing: $25.1{\pm}6.7$ vs. $32.4{\pm}1.9$, between the knee and ankle joint during stance: $46.0{\pm}12.9$ vs. $80.1{\pm}31.1$, between the knee and ankle joint during swing: $34.5{\pm}4.1$ vs. $37.6{\pm}3.1$, all p < 0.05). These results indicated that wearing knee brace affected joint angle and intra-limb coordination, but less affected gait features.
A najor current challenge and constraint in cervical cancer research is the development of vaccines against human papilloma virus (HPV) epitopes. Although many studies are done on epitope identification on HPVs, no computational work has been carried out for high risk forms which are considered to cause cervical cancer. Of all the high risk HPVs, HPV 16, HPV 18 and HPV 45 are responsible for 94% of cervical cancers in women worldwide. In this work, we computationally predicted the promiscuous epitopes among the E6 proteins of high risk HPVs. We identified the conserved residues, HLA class I, HLA class II and B-cell epitopes along with their corresponding secondary structure conformations. We used extremely precise bioinformatics tools like ClustalW2, MAPPP, NetMHC, Epi,Jen, EpiTop 1.0, ABCpred, BCpred and PSIPred for achieving this task. Our study identified specific regions 'FAFR(K)DL' followed by 'KLPD(Q)LCTEL' fragments which proved to be promiscuous epitopes present in both human leukocyte antigen (HLA) class I, class II molecules and B cells as well. These fragments also follow every suitable character to be considered as promiscuous epitopes with supporting evidences of previously reported experimental results. Thus, we conclude that these regions should be considered as the important for design of specific therapeutic vaccines for cervical cancer.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.