• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.221-223
• /
• 1999

In this work, samples were manufactured variously by changing conventional calcining and sintering conditions and we tried the utilization by making the heat treatment time, which is demanded to high-Tc phase formation, much shorter. We found out optimal heat treatment conditions with the analysis on formation process at superconducting phase in term of the change of calcining and sintering time and then, examined X-ray diffraction(XRD) patterns, scanning electron microscope(SEM) measurement and energy dispersive X-ray spectrometer(EDX) of the samples manufactured under heat treatment conditions which we suggest here. As a result, 2223 high-$T_c$, phase of (Bi,Pb)SrCaCuO superconductor starting with ($Bi_l$ xPbx,)$_2$$Sr_2$$Ca_2$$Cu_3$$O_y$, composition was formed from 1 hr sintering sample at temperature nearby melting point and also the completed sample with calcining and sintering time of 9 hr was formed high-$T_c$.low-$T_c$ phase appearing in sight above the critical temperature of liquid $N_2$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.10
• /
• pp.811-816
• /
• 2012

The effect of co-sputtering condition on the structural properties of $Mg_xZn_{1-x}O$ thin films grown by RF magnetron co-sputtering system was investigated for manufacturing ZnO/MgZnO structure LED. $Mg_xZn_{1-x}O$ thin films were grown with ZnO and MgO target varying RF power. Structural properties were investigated by X-ray diffraction (XRD) and Energy dispersive spectroscopy (EDS). The ZnO thin films have sufficient crystallinity on the high RF power. As RF power of ZnO target increased, the contents of MgO in the $Mg_xZn_{1-x}O$ film decreased. LED was manufactured using ZnO/MgZnO multi-layer on p-GaN/$Al_2O_3$ substrate. Threshold voltage of multi-layer LED was appeared at 8 V, and it was luminesced at wave length of 550 nm.

• Journal of the Korean Magnetics Society
• /
• v.13 no.4
• /
• pp.155-159
• /
• 2003

We report on the annealing effect and ferromagnetic characteristics of Zn$_{0.7}$Mn$_{0.3}$O film prepared by sol-gel method on the silicon (100) substrate using field emission-scanning electron microscopy (FE-SEM), energy dispersive spectroscopy (EDS), X-ray diffractometry (XRD) and superconducting quantum interference device (SQUID) magnetometry. Magnetic measurements show thatZn$_{0.7}$Mn$_{0.3}$O films exhibit ferromagnetism at 5 K revealing the coercive field of ∼110 Oe for as grown sample and 360, 1035 Oe for samples annealed at 700, 800 $^{\circ}C$, respectively. Our experimental evidence suggests that ferromagnetic precipitates of a manganese oxide may be responsible for the observed ferromagnetic behaviors of the film.he film.

• Journal of Hydrogen and New Energy
• /
• v.8 no.4
• /
• pp.173-180
• /
• 1997

The Mechanically Alloyed $Ti_{0.7}Mg_{0.3}Ni$ was investigated as a function of milling time by X-ray diffraction, SEM(scanning electron microscope), EDS(energy dispersive spectrometer), P-C-Isotherm curves. After 10hrs milling, mixed $Ti_{0.7}Mg_{0.3}Ni$ powders were changed to amorphous phase. And amorphous $Ti_{0.7}Mg_{0.3}Ni$ alloys became TiNi phase crystalline after heat treatment at 873K in a vacuum for 1 hour. The hydrogen absorption capacity of the annealed $Ti_{0.7}Mg_{0.3}Ni$ alloy increased as a function of mechanical alloying time.

• Journal of the Korean Chemical Society
• /
• v.66 no.5
• /
• pp.341-348
• /
• 2022

In this work, radio frequency magnetron sputtering was used to deposit zinc selenide thin films on p-type silicon (100) wafers and glass substrates in a high vacuum chamber. Several surface characterization instruments were implemented to study the thin films. X-ray photoelectron spectroscopy results revealed that oxidized Zn bound to Se (Zn-Se) at 1022.7 ± 0.1 eV becomes the dominant oxidized species when Se concentration exceeds 70%. Scanning electron microscopy coupled with energy dispersive spectroscopy showed that incorporating Se in Zn thin films will lead to formation of ZnSe grains on the surface. Contact angle measurements indicated that ZnSe-60 exhibited the lowest total surface free energy value of 24.94 mN/m. Lastly, ultraviolet-visible spectrophotometry and ultraviolet photoelectron spectroscopy data evinced that the energy band gap gradually increases with increasing Se concentration with ZnSe-70 having the highest work function value of 4.91 eV.

• Journal of Microbiology and Biotechnology
• /
• v.26 no.12
• /
• pp.2116-2126
• /
• 2016

Bacterial biofilms are spatially structured communities that contain bacterial cells with a wide range of physiological states. The spatial distribution and speciation of copper in unsaturated Pseudomonas putida CZ1 biofilms that accumulated 147.0 mg copper per g dry weight were determined by transmission electron microscopy coupled with energy dispersive X-ray analysis, and micro-X-ray fluorescence microscopy coupled with micro-X-ray absorption near edge structure (micro-XANES) analysis. It was found that copper was mainly precipitated in a $75{\mu}m$ thick layer as copper phosphate in the middle of the biofilm, while there were two living cell layers in the air-biofilm and biofilm-medium interfaces, respectively, distinguished from the copper precipitation layer by two interfaces. The X-ray absorption fine structure analysis of biofilm revealed that species resembling $Cu_3(PO_4)_2$ predominated in biofilm, followed by Cu-Citrate- and Cu-Glutathione-like species. Further analysis by micro-XANES revealed that 94.4% of copper were $Cu_3(PO_4)_2$-like species in the layer next to the air interface, whereas the copper species of the layer next to the medium interface were composed by 75.4% $Cu_3(PO_4)_2$, 10.9% Cu-Citrate-like species, and 11.2% Cu-Glutathione-like species. Thereby, it was suggested that copper was initially acquired by cells in the biofilm-air interface as a citrate complex, and then transported out and bound by out membranes of cells, released from the copper-bound membranes, and finally precipitated with phosphate in the extracellular matrix of the biofilm. These results revealed a clear spatial pattern of copper precipitation in unsaturated biofilm, which was responsible for the high copper tolerance and accumulation of the biofilm.

• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.381-386
• /
• 2011

Chemically functionalized plant oils, namely maleinized acrylated epoxidized soybean oil(MAESO), were used as a new bio based binders for photoelectrodes of dye-sensitized solar cells. The photocatalysts were characterized by field emission scanning electron microscope(FE-SEM), energy dispersive X-ray spectrometer(EDS), X-ray diffraction(XRD), X-ray photoelectron spectroscopy(XPS) and nitrogen adsorption analyses. The surface area and number of appropriate pores were increased in the $TiO_{2}$ particles prepared using the plant oil binders in comparison with the P-25 photocatalyst, due to the larger number of functionalities. The functional groups of OH on the surface of the $TiO_{2}$ particles increased from 9.9% to 16.62%.

• Journal of Surface Science and Engineering
• /
• v.56 no.5
• /
• pp.299-308
• /
• 2023

In this study, phosphorus (P)-doped nickel cobaltite (P-NiCo₂O₄) and nickel-cobalt layered double hydroxide (P-NiCo-LDH) were synthesized on nickel (Ni) foam as a conductive support using hydrothermal synthesis. The thermal properties, crystal structure, microscopic surface morphology, chemical distribution, electronic state of the constituent elements on the sample surface, and electrical properties of the synthesized P-NiCo₂O₄ and P-NiCo-LDH samples were analyzed using thermogravimetric analysis-differential scanning calorimetry (TGA-DSC), X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), energy dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), cyclic voltammetry (CV), galvanostatic charge-discharge (GCD), and electrochemical impedance spectroscopy (EIS). The P-NiCo₂O₄ electrode exhibited a specific capacitance of 1,129 Fg^-1 at a current density of 1 Ag^-1, while the P-NiCo-LDH electrode displayed a specific capacitance of 1,012 Fg^-1 at a current density of 1 Ag-1. When assessing capacity changes for 3,000 cycles, the P-NiCo₂O₄ electrode exhibited a capacity retention rate of 54%, whereas the P-NiCo-LDH electrode showed a capacity retention rate of 57%.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.5
• /
• pp.1123-1127
• /
• 2010

We report a simple and quick route for the preparation of high-quality, nearly monodisperse $Bi_2Te_3$, $Sb_2Te_3$, and $Bi_xSb_{2-x}-Te_3$ nanocrystallites. The reactions of bismuth acetate or antimony acetate with Te in oleic acid result in pure phase of $Bi_2Te_3$ or $Sb_2Te_3$ nanoparticles, respectively. Also, ternary $Bi_xSb_{2-x}Te_3$ nanoparticles were successfully synthesized using the same method. The size and morphology of the nanoparticles were controlled by varying the stabilizing agents. The as-prepared nanoparticles are characterized by X-ray diffraction, scanning electron microscope, and high-resolution transmission electron microscope using an energy dispersive spectroscopy.

• Journal of the Korean Magnetics Society
• /
• v.19 no.4
• /
• pp.121-125
• /
• 2009

Amorphous $Ge_1$_$_xMn_x$ semiconductor thin films grown by low temperature vapor deposition were annealed at various temperatures from 400 to $700^{\circ}C$ for 3 minutes in high vaccum chamber. The electrical and magnetotransport properties of as-grown and annealed samples have been studied. X-ray diffraction patterns analysis revealed that the samples still maintain amorphous state after annealling at $500^{\circ}C$ for 3 minutes and they were crystallized when annealing temperature increase to $600^{\circ}C$. Temperature dependence of resistivity measurement implied that as-grown and annealed $Ge_1$_$_xMn_x$ films have semiconductor characteristics, the increase of resistivity with annealling temperature was obseved. The $700^{\circ}C$-annealed sample exhibited negative magnetoresistance (MR) at low temperatures and the MR ratio was ${\sim}$8.5% at 10 K. The asymmetry was present in all MR curves. The anomalous Hall Effect was also observed at 250 K.