• Food Science of Animal Resources
• /
• v.25 no.1
• /
• pp.78-83
• /
• 2005

Purge & Trap method was applied to perform more simple and rapid detection for analysis of volatile flavor compounds in milk. Maximal sampling of 30 mL milk for glass flask sparger was treated by He gas purging for 2 hours. Reported major volatile compounds were detected by GC-MS after 2 hours absorption and desorbed from Purge & Trap equipped with Tenax trap. Volatile flavor compounds were analyzed by Purge & Trap and GC-MS to investigate the changes of flavor components in milk between raw and deodorized milk. Fourteen volatile compounds including acetaldehyde, ethanol, 2-propanone, dimethyl sulfide, isobutanal, 3-methyl 2-butanone, 2-butanone, 3-methyl butanal, pentanal, 3-hydroxy-2-butanone, methyl disulfide, hexanal, and 2 others were detected. Six compounds such as ethanol, dimethyl sulfide, pentanal, 3-hydroxy-2-butanone, and methyl disulfide were completely eliminated after deodorization treatment. Four compounds such as 3-methyl 2-butanone, 2-butanone, 3-methyl butanal, and an unknown compound 81 (M/sup +/) were also decreased after raw milk was deodorized. The other four compounds such as acetaldehyde, 2-propanone, hexanal, and an unknown compound (M/sup +/) were not decreased.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.2
• /
• pp.89-94
• /
• 1997

A new type SO$_2$ gas sensor with a particular inorganic thin film on SAW devices was developed. The sensor consisted of twin SAW oscillators of the center frequency of 54 MHz fabricated on the LiTaO$_3$ piezoelectric single crystal. One delay line of the sensor was coated with a CdS thin film that selectively adsorbed and desorbed SO$_2$, while the other was uncoated for use as a stable reference. Deposition of the CdS thin film was carried out by the spray pyrolysis method using an ultrasonic nozzle. The sensor could measure the concentration in air less than 0.25 parts per million of SO$_2$. Stability of the sensor turned out to be as good as less than 20ppm, recovery time after each measurement was as short as 5 minutes. Repeatability of the measurement was confirmed through so many reiterated experiments. Hence, the SAW sensor developed through this work showed promising performance as a microsensing tool of SO$_2$. Further work required to improve the performance of the sensor includes enhancement of the reactivity of the CdS thin film with SO$_2$ through appropriate dopant addition, an increase of the center frequency of the SAW device.

• KSBB Journal
• /
• v.10 no.5
• /
• pp.491-498
• /
• 1995

In order to fraclionate ${\alpha}$-, ${\beta}$- and ${\gamma}$-cyclodextrins(CDs) from CD reaction mixture, various CD adsorbents were manufactured using fatty acids as the ligand molecules and anion exchange resins as matrix. Among several anion exchange resins, DEAE Cellulose was found to be the most suitable matrix for binding fatty acid. The binding stability between DEAE Cellulose and capric acid was tested under the various operation conditions, such as temperature, ethanol concentration, and ionic strength. Specific CD adsorbents manufactured with different chain-length fatty acids, saturated and unsaturated, were compared in terms of the recovery yield and selectivity of ${\alpha}$-, ${\beta}$- and ${\gamma}$-CDs. Stearic acid (C18, saturated) was identified as the most effective ligand for fractionation of ${\alpha}$-CD, and linoleic acid ((C18, unsaturated ) for ${\beta}$-CD. The spacer length between the matrix and ligand was required for effective adsorption of CDs, and the double bond in fatty acid molecules was also acted as an important factor determining recovery yield and selectivity. The elusion patterns of ${\alpha}$- and ${\alpha}$-, ${\beta}$-CD from column packed with stearic acid and linoleic acid CD adsorbents were also investigated at the various elusion conditions for fractionation of ${\alpha}$- and ${\beta}$-CD.

• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.133-141
• /
• 2019

High specific surface area zirconia with acid-basic property was synthesized by precipitation using reflux method or hydrothermal synthesis method using ammonium hydroxide solution as precipitant in the range of pH of Zr solution from 2 to 10. The prepared zirconia was characterized by the nitrogen adsorption, X-ray diffraction (XRD), isopropanol temperature programmed desorption (IPA-TPD), scanning electron microscopy and X-ray photoelectron spectroscopy, and the catalytic activity in the IPA decomposition reaction was correlated with the acid-basic properties. When using reflux method, high pH of Zr solution was required to obtain high fraction of tetragonal zirconia, and pure tetragonal zirconia was possible at pH 9 or higher. High pH was required to obtain high specific surface area zirconia, and the hydrous zirconia synthesized at pH 10 had high specific surface area zirconia of $260m^2g^{-1}$ even after calcination at $600^{\circ}C$. However, hydrothermal synthesis with high pressure under the same conditions resulted in very low specific surface area below $40m^2g^{-1}$ and monoclinic phase zirconia was synthesized. High pH of the solution was required to obtain high specific surface area tetragonal phase zirconia. In hydrothermal synthesis requiring high pressure, monoclinic zirconia was produced irrespective of the pH of the solution, and the specific surface area was relatively low. Zirconia with high specific surface area and tetragonal phase was predominantly acidic compared to basicity and only propylene, which was observed as selective dehydration reaction in IPA decomposition reaction, was produced.

• Resources Recycling
• /
• v.27 no.6
• /
• pp.23-29
• /
• 2018

Recently rapid economic growth and technological development have led to an increase in the generation of waste electrical and electronic equipment (WEEE). As the amount of electric and electronic waste generated increases, the importance of processing waste printed circuit boards (PCB) is also increasing. Various studies have been conducted to recycle various valuable metals contained in a waste PCB in an environmentally friendly and economical manner. To get anode slime containing Ag and Au, Anode copper prepared from PCB scraps was used by means of electro-refining. Ag and Au recovery was conducted by leaching, direct reduction, and ion exchange method. In the case of silver, the anode slime was leached at 3 M $HNO_3$, 100 g/L, $70^{\circ}C$, and Ag was recovered by precipitation, alkali dissolution, and reduction method. In the case of gold, the nitrate leaching residues of the anode slime was leached at 25% aqua regia, 200 g/L, $70^{\circ}C$, and Au was recovered by pH adjustment, ion exchange resin adsorption, desorption and reduction method. The purity of the obtained Au and Ag were confirmed to be 99.99%.

• Journal of the Korean Society of Urban Environment
• /
• v.18 no.4
• /
• pp.523-530
• /
• 2018

Kyoto Protocol, adopted in 1997, set the obligation to reduce $CO_2$, $CH_4$, $N_2O$, HFCs, PFCs, and $SF_6$ in developed countries during 1st promised period. $SF_6$ has been drawing a lot of attention since the Kyoto Protocol because once it is released into the atmosphere, it not only stays in the atmosphere for more than 3,200 years but also emits 22,800 times stronger global warming potential at the same concentrations as $CO_2$ if remains in the atmosphere for 100 years. This study introduces 12 methods for $SF_6$ of measuring trace. $SF_6$ of trace level in the atmosphere correctly, the measurement method was changed and as a result, when the back flush method was applied to the pre-concentration system that used low-temperature concentration and high-temperature desorption system, which used Carboxen-1000 adsorption trap, the effect was the best.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.4
• /
• pp.463-475
• /
• 2020

Presence of microplastics in soil and groundwater has recently been reported and environmental concerns are raised as to the plastic pollution. In the subsurface environment, clay minerals and metal oxide minerals are commonly found as finely dispersed states. Because the minerals have high sorption capacities for diverse pollutants, interactions with mineral surface play an important role in the transport of microplastics in groundwater. Accordingly, environmental mineralogy investigating the interactions between microplastics and mineral surfaces is the essential research area to understand the fate and transport of microplastics in the subsurface environment. The microplastic-mineral surface research requires molecular- to nano-scale analyses to be able to probe the relatively weak interactions between them. The current report introduces a nano-scale analysis tool called quartz crystal microbalance (QCM) that can measure the sorbed/desorbed mass of nanoplastics on mineral surfaces at the level of a few nanograms (~10-9 g). This report briefly reviews the main principles in the QCM measurement and discusses applications of QCM to the environmental mineralogy research.

• Korean Chemical Engineering Research
• /
• v.60 no.4
• /
• pp.620-629
• /
• 2022

By varying various experimental conditions such as heating rate, molar hourly space velocity (MHSV), and nitridation reaction temperature, vanadium oxynitride was prepared through temperature programmed reduction/nitridation reaction (TPRN) of vanadium pentoxide and ammonia, and characterization were performed. In order to investigate the physico-chemical properties of the prepared catalyst, N₂ adsorption-desorption analysis, X-ray diffraction analysis (XRD), hydrogen temperature programmed reduction (H₂-TPR), temperature programmed oxidation (TPO), ammonia temperature programmed desorption (NH₃-TPD), transmission electron microscopy (TEM) was performed. Transformation of V₂O₅ with 5 m² g^-1 low specific surface area by reduction at 340 ℃ to V₂O₃ showed a high specific surface area value of 115 m² g^-1 by micropore formation. As the nitridation temperature increased beyond that, the specific surface area continued to decrease due to sintering. The nitridation reaction variable that had the greatest influence on the specific surface area was the reaction temperature, and the x + y value of VN_xO_y of a single phase approached from 1.5 to 1.0 as the nitridation reaction temperature increased. At a high reaction temperature of 680 ℃, the cubic lattice constant a was VN. close to the value. At 680 ℃, the highest nitridation temperature among the experimental conditions, the ammonia conversion rate was 93%, and no deactivation was observed.

• Analytical Science and Technology
• /
• v.20 no.3
• /
• pp.237-245
• /
• 2007

The presence of benzene in 31 products of vitamin drinks purchased from 20 retail outlets was determined using headspace solid phase microextraction (HS-SPME) and gas chromatography-mass spectrometry (GC-MS). The sample (25 ml) was stirred at 1200 rpm for 4 min using a magnetic bar with a $100{\mu}m$ SPME fiber as an adsorbent for benzene which was then desorbed from the fiber for 1 min in the GC injector. Quantitation was achieved using the standard addition method. The limit of detection was determined as 0.56 ng/ml and over a concentration range 0-40 ng/ml the coefficient of correlation was greater than 0.999. The concentration of benzene in the drinks examined was in the range not detectable to 47.35 ng/ml. Benzene was detected in 15 of the drinks with concentration in 5 of them greater than 10 ng/ml which is the limit set for the presence of benzene in the Drinking Water Regulations. The concentrations of benzene in the 5 drinks which exceeded the limit of 10 ng/ml were 16.99, 35.14, 16.03, 47.35 and 14.28 ng/ml respectively.

• Applied Chemistry for Engineering
• /
• v.34 no.6
• /
• pp.612-618
• /
• 2023

Modern society spends more than 80% of its daily life indoors, emphasizing the need for attention to indoor air pollution due to the improvement in living standards. In this study, the performance and reaction characteristics of the Pt/TiO₂ catalysts prepared by liquid-phase reduction for the removal of formaldehyde (HCHO), one of the indoor air pollutants, at room temperature without the need for additional light or heat were investigated. As a result, it showed that catalysts prepared by the same method showed approximately 40~80% various activities depending on the type of TiO₂. XRD, BET, and XPS analyses were performed to investigate the particle size, crystal structure, specific surface area, and O/Ti molar ratio of the support material, and it revealed that the correlation between the properties and performance was insignificant. To explore the oxidation reaction pathway of formaldehyde (HCHO), in situ DRIFT analysis using carbon monoxide and H₂-TPR was perfomed. The results revealed that the performance was demonstrated by the oxidation state of the active metal and the adsorption-desorption characteristics of the adsorbate species.