• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.8
• /
• pp.519-525
• /
• 2016

In a pump, from the performance point of view, it is very important to minimize the shock loss at the inlet of the rotor blades. In this study, the effects of shape and install angle of the inlet guide on the performance of an axial-flow pump are numerically simulated using commercial CFD code, Ansys CFX. Finally, to obtain the optimized shape of the vanes and the install angle of the vanes in the inlet guide under given operating conditions, optimization analysis is conducted using Analysis design exploration based on response surface optimization.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.705-708
• /
• 2011

Ejector system can induce the secondary flow or affect the secondary chamber pressure by both shear stress and pressure drop which are generated in the primary jet boundary. Ejectors are widely used in a range of applications such as a turbine-based combined-cycle propulsion system and a high altitude test facility for rocket engine, pressure recovery system, desalination plant and ejector ramjet etc. The primary interest of this study is to set up an design procedure on the configuration and operating condition of multi-ejector for the various high altitude simulation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.10a
• /
• pp.17-17
• /
• 1999

액체램제트 추진기관은 고체로케트 추진기관에 비해 복잡한 구조와 작동원리를 가지고 있지만 산화제인 공기를 대기로부터 직접 흡입하므로 비행체의 크기와 중량을 줄이고 순항거리를 최대한 증대시킬 수 있는 장점을 가지고 있다. 이러한 램제트 추진기관의 개발 및 실용화를 위해서는 램제트 추진기관의 유동 및 연소지상시험 설비의 구축이 필수적이다. 본 연구에서는 그 기초연구로서 연소기 입구의 속도, 온도와 같은 실제 액체램제트 추진기관의 비행조건을 완벽하게 모사할 수 있는 Vitiated Air Heater의 설계기술 확보에 연구목적을 두었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.8
• /
• pp.671-676
• /
• 2014

The vortex cup is proposed as a method to transport sensitive products such as silicon wafers in manufacturing. Air through the inlet nozzle located at the top of the vortex cup flows to form a swirl in the cylinder. The flow located in the lower part of the thin gap between the vortex cup and the bottom surface escapes and generates a negative pressure that can lift objects. In this research, three-dimensional numerical simulation of the air flow field in a vortex cup is performed, and a comparison of the simulation and experimental results shows very good agreement. In addition, the vortex cup length and shape that affect the negative pressure were applied to the analysis. Through the simulation results, optimum conditions for the vortex cup shape were proposed.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1998.10a
• /
• pp.14-14
• /
• 1998

램제트 엔진은 초음속에서 공기가 충격파를 통해 아음속으로 속도가 낮아지고 압력이 증가하는 램 압축 현상을 이용하되 압축기를 사용하지 않고 아음속 상태에서 연소하는 구조로 되어 있다. 따라서 각 부품의 성능은 독립적이지 않으며 전체적인 성능을 규명하기 위해서는 공기 흡입구와 연소실, 연료 분사체계 등의 상호작용을 고려하여 유동의 특성과 그에 따른 연소현상의 특성을 함께 고려해야만 한다. 본 연구에서는 속도 범위 Mach 5이내, 고도 30km이내의 운항조건을 갖는 유도 무기에 장착될 램제트 엔진 개발을 위한 연구의 첫 번째 단계로써, 램제트 연소실내의 유동장해석을 실험과 수치해석 두 분야로 나누어 수행하였다.

• Fire Science and Engineering
• /
• v.33 no.4
• /
• pp.35-40
• /
• 2019

In this study, the mass flow rate of the heat release rate equation, which is the major factor of the oxygen consumption method, was analyzed for the fundamental investigation of the cone-calorimeter (5 m length and 0.3 m diameter). The shapes of a completely empty inside, 3 mm pore diameter mesh and pore diameter 10 mm honeycomb with 0.76 porosity were constructed using the cone-calorimeter. To calculate the mass flow rate, four bi-directional probes and thermocouples were installed in a uniform position in the vertical direction of flow. The velocity gradient and flow perturbation were measured from the increase in Reynolds number. As the flow capacity increased, the speed gradient increased in all three shapes relative to the turbulence intensity. In addition, the deviation of extended uncertainty to the mass flow was completely low in the order of empty space, mesh (d_p = 3 mm) and honeycomb (d_p = 10 mm and 𝜖 = 0.76) at the 95% confidence level. The results can be used in designs to improve the flow stability of the cone calorimeter.

• Membrane Journal
• /
• v.28 no.4
• /
• pp.252-259
• /
• 2018

An acidic, real metal-plating wastewater was treated by a fluidized bed membrane reactor introduced with granular activated carbon (GAC) as fluidized media. With GAC fluidization, there was no increase in suction pressure with time at each flux set-point applied. At neutral solution pH, much less fouling rate was observed than acidic pH under GAC fluidization. Higher solution pH resulted in the increase in particle size in metal-finishing wastewater, thus producing a less dense cake structure on membrane. More than 95% of chemical oxygen demand was observed from the fluidized bed membrane reactor under GAC fluidization. Total suspended solid concentration in membrane permeate was near zero. At the raw wastewater pH, no removal of copper and chromium by the fluidized bed membrane reactor was observed. As the pH was increased to 7.0, removal efficiency of copper and chromium was increased considerably to 99 and 94%, respectively. Regardless of solution pH tested, more than 95% of cyanide was removed possibly due to the strong adsorption of organic-cyanide complex on GAC in fluidized bed membrane reactor.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.3
• /
• pp.1-7
• /
• 2018

A combustion test for a supersonic combustor was conducted using a direct-connected type supersonic combustor test facility. The facility was verified for the capability of simulating required flow conditions. The test condition was maintained at Mach 2.0, $915^{\circ}C$ and 496 kPa for 15 s. Using gaseous hydrogen as the fuel, the combustor model was also tested for its ignition and flame holding capability at the fuel equivalence ratio of 0.12. Combustion efficiency was 71%, and the supersonic flow regime was obtained at this test condition.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.62-72
• /
• 2004

In this paper. firstly, numerical results were compared with experimental results to verify accuracy of the results. It is found that the numerical results show good agreements with experimental result. Next, computations about flow within blades for design parameters such as radius of the pressure and suction side's curvature and pitch-chord ratio have been performed. It is found that the flow and performance characteristics mainly depend on shocks occurred at the leading edge of blades and the end of nozzle and separations occurred inside the flow passage. And shock of nozzle and separations depend upon area of flow passage and shocks of blade are affected by the number of blades occupied by a nozzle.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.996-999
• /
• 2011

The flow and combustion dynamics in the ignition and ramjet sustainer phase of an integrated rocket-ramjet(IRR) engine are investigated. The physical model includes the entire engine flowpath, from the freestream in front of the inlet to the exit of the exhaust nozzle. The flowfield obtained from a rocket booster study is used as the initial condition for the present analysis, so that the complete operation history of the engine can be obtained. The analysis for the primary factor governing flame propagation during the ignition and the key mechanisms for driving and sustaining the flow oscillations are performed.