• Journal of the Korean Geotechnical Society
• /
• v.19 no.4
• /
• pp.191-200
• /
• 2003

This paper presents the rheological properties of bitumen for reducing negative skin friction. The bitumen has been widely used due to both the cost and construction effectiveness. Also, it is well known that the use of bitumen for reducing negative skin friction renders the best results among other available methods. Three different modified bitumens were used for the testing programs. The physical tests include the penetration, the softening point and penetration index. The rheological tests include phase angle, complex modulus, creep tests and flow tests. The tests were conducted at four different temperatures(15, 30, 45 and 6$0^{\circ}C$) in order to simulate the field condition. The test results were analyzed using the phase angle, G$^*$/sin $\delta$, creep compliance and shear viscosity. The result of tests showed that the phase angle increased and G$^*$/sin $\delta$ decreased with the increase of temperature. The creep compliance increased as the loading time increased. The difference of the creep compliance is detected as the time and temperature are varied, however, the difference of the shear viscosity is not significant among the samples tested in this study. The rheological properties of the bitumen also showed that the physical testing method and the temperature dependant testing method are somewhat limited to showing and expressing the full rheological properties of the modified bitumen. The introduction of the time and the temperature dependent testing method is necessary to find out the full rheological properties of the modified bitumen.

• Journal of Wetlands Research
• /
• v.14 no.4
• /
• pp.699-713
• /
• 2012

Palustrine wetland is often used for development work and green area creation. However, the ecological characteristic of vegetation is not frequently considered in planning. Therefore, this study was conducted to investigate vegetation characteristic according to land-use of palustrine wetland and to provide basic materials in assessment of palustrine wetland and restoration and creation of wetland. Survey sites were caterogized into paddy, field, and mountain. Each category had two sites, so total 6 survey sites were investigated for vegetation. As a result, with a range of 61~92 species, total 216 taxa were confirmed, consisting of 71 families, 168 generic, 187 species, 2 variety 1 forma 1 subforma. Mountain received a high score in the evaluation score range of floristic regional indicator plants, and it was found that there were 10 families and 28 species of naturalized plant. Mountain showed low appearance, and fiddy and field showed relatively high appearance. Naturalized plants with slightly high vegetation cover ratio are Erigeron annuus, Amorpha fruticosa, Dactylis glomerata, Festuca arundinacea, Eragrostis curvula, Trifolium repens, Erigeron Canadensis, Ambrosia trifida, Oenothera odorata, Bidens frondosa, etc. Such naturalized plants should be removed to prevent terrestrialization of wetland and its harmful damages. Long-term monitoring and proper management of naturalized plants are expected to improve palustrine wetland into high quality biotope of rural area in the future.

• The Journal of Engineering Geology
• /
• v.24 no.4
• /
• pp.501-510
• /
• 2014

Volcanic eruptions alone may lead to serious natural disasters, but the associated release of water from a caldera lake may be equally damaging. There is both historical and geological evidence of the past eruptions of Mt. Baekdusan, and the volcano, which has not erupted for over 100 years, has recently shown signs of reawakening. Action is required if we are to limit the social, political, cultural, and economic damage of any future eruption. This study aims to identify the area that would be inundated following a volcanic flood from the Cheon-Ji caldera lake that lies within Mt. Baekdusan. A scenario-based numerical analysis was performed to generate a flood hydrograph, and the parameters required were selected following a consideration of historical records from other volcanoes. The amount of water at the outer rim as a function of time was used as an upper boundary condition for the downstream routing process for a period of 10 days. Data from the USGS were used to generate a DEM with a resolution of 100 m, and remotely sensed satellite data from the moderate-resolution imaging spectroradiometer (MODIS) were used to show land cover and use. The simulation was generated using the software FLO-2D and was superposed on the remotely sensed map. The results show that the inundation area would cover about 80% of the urban area near Erdaobaihezhen assuming a 10 m/hr collapse rate, and 98% of the area would be flooded assuming a 100 m/hr collapse rate.

• Ecology and Resilient Infrastructure
• /
• v.3 no.4
• /
• pp.307-314
• /
• 2016

River restoration has recently been performed not only for the improvement of the artificial parts in the past but also for the restoration of abandoned river reaches which were blocked and isolated. For the restoration of abandoned river reaches, it is important to recover the hydraulic and ecological connectivity in the isolated space by longitudinal structures like levees. But because the assessment tools to determine whether the river restoration is performed properly are so rare at present, we aim to provide a tool for assessing ecological connectivity in a target river in this study. In the first step, one-dimensional numerical model for rainfall-runoff and channel routing was developed and then applied to the watershed of the Cheongmi Stream. In this step, a numerical model was developed to assess the restoration of connectivity. The model consists of two parts: one part is to convert the results of one-dimensional channel routing into two-dimensional spatial distribution. The other is to calculate the habitat suitability index according to time steps by using two-dimensional hydraulic features. The model was applied to a restoration area of the Cheongmi Stream. The advantage of this study is that two-dimensional hydraulic analysis can be easily obtained from one-dimensional hydraulic analysis without a complex and time-consuming two-dimensional analysis. HHS (Hydraulic Habitat Suitablility) by sections of target reaches and target species can be easily obtained using the results of this study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.480-488
• /
• 2016

As the subprime mortgage crisis spread globally, it depressed not only the financial market, but also the construction business in Korea. In fact, according to CERIK, the BSI of the construction businesses plunged from 80 points in December 2006 to 14.6 points in November 2008, and the extent of the depression in the housing sector was particularly serious. In this respect, this paper analyzes the influence of the financial market fluctuation on the housing market before and after the Global Financial Crisis using VECM. The periods from January 2000 to December 2007 and January 2008 to October 2015, before and after the financial crisis, were set as Models 1 and 2, respectively. The results are as follows. First, when the economy is good, the Gangnam housing market is an attractive one for investment. However, when it is depressed, the Gangnam housing market changes in response to the macroeconomic fluctuations. Second, the Gangbuk and Gangnam housing markets showed different responses to fluctuations in the financial market. Third, when the economy is bad, the effect of low interest rates is limited, due to the housing market risk.

• Korean Journal of Ecology and Environment
• /
• v.43 no.2
• /
• pp.175-182
• /
• 2010

From April to October 2008, fish fauna was surveyed at 25 sites in Lake Ganwol and Lake Bunam watersheds. There were 32 species of 25 genera and 10 families belonging to 5 orders. Among them, Zacco platypus (relative abundance was 28.0%) was dominant, followed by Hemiculter eigenmanni (24.3%), Carassius auratus (19.3%), and Pseudorasbora parva (10.8%). In comparison of specific frequency in fish community between two lakes, Z. platypus (36.6%) was dominant and P. parva (15.7%) subdominant in Lake Ganwol, whereas H. eigenmanni (35.2%) and C. auratus (30.4%) were dominant in Lake Bunam. Eight species including Acheilognathus chankaensis were known to be Korean endemic species, and exotic species was Micropterus salmodes. Biological indices of fish community indicated mostly similar values in 25 sites. Specific similarities of fish community in the sites were largely divided into two groups: a group of the Waryong Stream and the Dodang Stream where water flows throughout the year, and the other group of watersheds at Lake Ganwol and Lake Bunam where water was static. Fish fauna and structure of fish communities have some differences between Lake Ganwol and Lake Bunam watersheds, and also can be distinguished to the environmental factors of habitats in same watershed.

• Korean Journal of Food Science and Technology
• /
• v.19 no.6
• /
• pp.499-505
• /
• 1987

The functional properties of lupin seed protein concentrate (LPC) were examined and compared to those of soybean protein isolate (SPI) and Na-caseinate. LPC-50, of which protein level was 50%, was prepared by a two phase solvent (hexane: alcohol: water= 10:7:3) extraction method. LPC-70 was made from LPC-50 by removing the fractions solubilized by carbohydrate decomposing enzymes. The solubilities of LPC-50 and LPC-70 were similar to that of of SPI but slightly higher at pH 4-5, and less susceptible to the added salt. The apparent viscosity of LPC increased exponentially as the concentration increased over 6% level, and the change was similar to that of Na-caseinate. LPC showed strong pseudoplastic non-Newtonean flow behavior, which was similar to that of SPI The emulsifying capasity of LPC-70 was similar to that of SPI when salt was added. The foaming capacity of LPC was comparable to that of SPI. LPC showed high oil and water absorption capacities, which increased as the protein level was elevated. LPC-70 showed the highest oil absorption capacity of all the samples tested.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.38 no.1
• /
• pp.57-67
• /
• 2020

Recently, smart cities are attracting attention as a solution for a plethora of urban problems, including transportation, environment, safety, and energy. However, despite a substantial body of research dealt with the concept, trends, policy, and legal institutions of smart cities, few researchers have examined how the smart city services influence the cities from the dynamic perspective that considers the entire cycle of a city, including its growth, stagnation, and decline. Thus, it is vital to understand how the city changes with time from the view that a city is a system of sub-elements-population, industry, transportation, environment, housing, and land-closely interacting together. Within this context, this study explores how the urban dynamics of Anyang-city develop for the long term using the System Dynamics method and analyzes the effect of smart city project investment on the dynamics of Anyang-city. According to the result, Anyang-city is a "mature and stable" type, and its population is expected to decrease slowly by 2040. Specifically, the Anyang-city population will be reduced to 553,000 by 2030. It was analyzed that the number will decrease to 543,000 by 2040. It was also found that the investment in smart city projects in Anyang, based on the Plan for Anyang Smart City, would have the following effects: easing population decline, increasing number of businesses, improving urban safety index, and increasing average driving speed. The population will grow by 4,000 and the number of businesses will increase by 761 than before budget investment. The result of this paper is expected to contribute to identifying and predicting the effect of smart city policies from a long-term perspective.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.399-403
• /
• 2007

Trans-esterification behavior of polycarbonate/poly(butylene terephthalate) (PC/PBT) blends was investigated during the melt mixing process. Rheological and fracture behaviors, and fracture morphology were also investigated as a function of PC/PBT blend ratio. Based on FT-IR and $^1H-NMR$ results, a trans-esterification reaction was confirmed to occur between PC and PBT during the melt mixing process. The melt index(MI) decreased with increased PC content, indicating the higher flow resistance of PC. The storage and loss moduli were increased by increasing the PC loading, and the PC/PBT blends were rheologically incompatible based on the Cole-Cole plot. The tensile property increased linearly with the increased PC content. However, the impact strength increased until 50 wt% of PC loading, notably around $30{\sim}40wt%$, and then was levelled off at 50 wt%. Rough ridges were formed on the impact fracture surfaces above the 40 wt% of PC content, supporting the observed higher impact strength in this range.

• Elastomers and Composites
• /
• v.49 no.3
• /
• pp.181-190
• /
• 2014

Melt grafting of itaconic acid (IA) onto an ethylene-propylene-diene terpolymer (EPDM) with various organic peroxide initiators was performed. Finding the optimum mixing conditions and concentration of ingredients is critical for effective grafting and optimum properties of grafted materials. This study focused on the effects of mixing conditions (temperature and time), initiator type/concentration and monomer concentration on the grafting degree and efficiency, melt flow index, and gel content of EPDM-g-IA. The initiator, 2,5-dimethyl-2,5-di(tert-butyl peroxy)-hexane (T-101), appeared to meet for the best grafting degree (1.91%). The grafting degree increased markedly by increasing the amounts of monomer IA and initiator T-101. The grafting degree also increased by increasing mixing temperature and time. The optimum monomer and initiator concentrations and reaction temperature and time were found to be about 5wt%/0.05wt% and $160^{\circ}C$/15min, respectively. It was found that the physical properties of EPDM-g-IA were higher than those of the pristine EPDM.