• Journal of agricultural medicine and community health
• /
• v.18 no.1
• /
• pp.77-91
• /
• 1993

This study was conducted to assess health medical center utilization pattern and its related factors among the rural inhabitants for the purpose of contribution to establishment of health medical center institutions. A questionnaire survey was carried out for object of 3,754 population of three primary school and three middle school student's parents (total 832 household) in Kyungbook Ulchin Gun rural area from 24 to 28 September, 1990. The summarized result are as follows, Respondents are 60.3% in male, 39.7% in female and 30-40s 81.3% in age, high school graduates 40.3% in education level and a regional medical insurance scheme in 44.1% in forms of health insurance. Recognition for health medical center was showed higher according to high educational, high income level, and short distance for location of health medical center of respondents (p < 0.01). Recognition for health medical center services was showed higher about care of medicaid in medical treatment services and higher preventive vaccination in health prevention services by respondents. Utilization rates of health medical center by out-patient care and preventive care service were 11.1 and 4.5 per 100 persons by year, but admission utilization rate was 34.6 per 10.000 persons by year. Motivations of health medical center utilization were showed a good care(45.7%), a good drugs(45.2%), and nearby health medical center(42.9%). In comparison health service levels of health medical center with general clinic was better (16.3%), similar(38.7%), 7(19.0%), and worse(19.0%) in view of health medical center utilizators. Inconvinience about health medical center utilized was the most higher longtime waiting, the next was limited utilization times. Transportation utilited were on foot(55%), by bus(35.5%), and so on. As mentioned above, there are many inhabitants who less understanding and less acknowledgement about health medical center and even mistake health center for health medical center. Therefore, there must be more information about health medical center. For higher utilization of health medical center, there must be considered expansion of health equipment, facilities, accomplishment with reinforcement of health staffs and efficiency management.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.3
• /
• pp.75-85
• /
• 2009

This work proposes a 13b 100MS/s 0.13um CMOS ADC for 3G communication systems such as two-carrier W-CDMA applications simultaneously requiring high resolution, low power, and small size at high speed. The proposed ADC employs a four-step pipeline architecture to optimize power consumption and chip area at the target resolution and sampling rate. Area-efficient high-speed high-resolution gate-bootstrapping circuits are implemented at the sampling switches of the input SHA to maintain signal linearity over the Nyquist rate even at a 1.0V supply operation. The cascode compensation technique on a low-impedance path implemented in the two-stage amplifiers of the SHA and MDAC simultaneously achieves the required operation speed and phase margin with more reduced power consumption than the Miller compensation technique. Low-glitch dynamic latches in sub-ranging flash ADCs reduce kickback-noise referred to the differential input stage of the comparator by isolating the input stage from output nodes to improve system accuracy. The proposed low-noise current and voltage references based on triple negative T.C. circuits are employed on chip with optional off-chip reference voltages. The prototype ADC in a 0.13um 1P8M CMOS technology demonstrates the measured DNL and INL within 0.70LSB and 1.79LSB, respectively. The ADC shows a maximum SNDR of 64.5dB and a maximum SFDR of 78.0dB at 100MS/s, respectively. The ABC with an active die area of $1.22mm^2$ consumes 42.0mW at 100MS/s and a 1.2V supply, corresponding to a FOM of 0.31pJ/conv-step.

• Korean Journal of Agricultural Science
• /
• v.9 no.1
• /
• pp.357-370
• /
• 1982

Recent concern regarding price and availability of fossil fuels has spurred the interest in alternative sources for farm crop drying. Among the available options such as biomass energy, wind power, nuclear energy and solar energy etc., the increasing attention is being directed to the utilization of heat from solar energy especially for farm crop drying. Even though solar energy is dispersed over a large land area and only a relatively small amount of energy can be simply collected, the advantages of solar energy is that the energy is free, non-polluting. The study reported here was designed to help supply the informations for the development of simple and relatively inexpensive solar warehouse for farm crop drying and storage. Specifically, the objectives of this study were to determine the performance of the solar collector fabricated, to compare solar supplemented heat drying with natural air drying and to develop a simulation model of temperature in stored grain, which can be used to study the effects due to changes in ambient air temperature. For those above objectives, solar collector was fabricated from available materials. Corrugated steel galvanized sheet, painted flat black, was used as absorbers and clear 0.2mm polyethylene sheet was the cover material. The warehouse for rough rice drying and storage was constructed with concrete block, and the solar collector was used as the roof of warehouse instead of original roofing system of it. The results obtained in this study were as follows: 1. The thermal efficiency of the solar collector was average 26 percent and the overall heat transfer coefficient of the collector was approximately $25kJ/hr.m^2\;^{\circ}K$. 2. Solar heated air was sufficient to dry one cubic meter of rough rice from 23.5 to 15.0 percent in 7 days and natural air was able to dry the same amount of rough rice from 20.0 to 5 percent in l2 days. 3. Drying with solar heat reduced the required drying time to dry the same amount of rough rice into a half compared to natural air drying, but overdrying problems of the bottom layer were so severe that these problems should be thoroughly analyzed. 4. Simulation model of temperature in stored grain was developed and the results of predicted temperature agreed well with test results. 5. Based on those simulated temperature, changes in the grain-temperature were a large at the points of the wallside and the damage of the grain would be severe at the contact area of wall.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.517-528
• /
• 2007

Domestic or international existing researches regarding rail damage factors are focused on laying, vehicle conditions, driving speed and driving habits and overlook characteristics of track structure (elasticity, maintenance etc). Also in ballast track, as there is no special lateral spring stiffness of track also called as ballast lateral resistance in concrete track, generally, existing study shows concrete track has 2 time shorter life cycle for rail replacement than ballast track due to abrasion. As a result of domestic concrete track design and operation performance review, concrete track elasticity is lower than track elasticity of ballast track resulting higher damage on rail and tracks. Generally, concrete track has advantage in track elasticity adjustment than ballast track and in case of Europe, in concrete track design, it is recommended to have same or higher performance range of vertical elastic stiffness of ballast track but domestically or internationally review on lateral spring stiffness of track is very minimal. Therefore, through analysis of service line track on site measurement and analysis on performance of maintenance, in this research, dynamic characteristic behaviors of commonly used ballast and concrete track are studied to infer elasticity of service line track and experimentally prove effects of track lateral spring stiffness that influence curved rail damage as well as correlation between track elasticity by track system and rail damage to propose importance of appropriate elastic stiffness level for concrete and ballast track.

• The Journal of Engineering Research
• /
• v.3 no.1
• /
• pp.199-205
• /
• 1998

Cullet Quality Control in auto glass bottle factory is the most important in recent days because of the increasing cost of materials in glass bottle. Since the composition of plate glass cullet is similar, the cullet quality using plate cullet in glass bottle factory is easily controlled. In addition to this, the price of plate glass cullet is so low that the cost reduction can be achieved. If the ratio of plate glass cullet and gush is over 25%, the liquidity of glass water become worse, which is caused by different compositions and viscosity of the components. As a results, Furnace bottom temperature becomes low and glass water becomes inhomogeneous. Thus production efficiency of glass bottle becomes low because of increasing devitrification in Dead Corner part in glass melting furnace. Three experimental methods – (1) increasing melting temperature, (2) using Booster, (3) using bubbler – were performed to increase the furnace bottom temperature and glass water homogeneity. The amounts of plate glass cullet was able to increase up to 90%, 70% and 60% without any devitrification using booster, bubbler and the method of glass melting temperature increase from $1480^{\circ}C$ to $1560^{\circ}C$ respectively. It is not possible to increase the glass melting temperature without the reduction of furnace operation time and the increase of fuel cost. The booster process has disadvantage of much electric energy consumption. Since the bubbler process uses physical convection of melting glass based on compression air, the homogeneity of molten glass is not so good as that of booster process but it can reduce the cost of glass bottle.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.32 no.3
• /
• pp.486-493
• /
• 2008

Safflower red colorants extracted by two solvents including the traditional ash solution and $K_{2}CO_{3}$ solution was used for dyeing cotton, ramie, viscose rayon, silk, wool, and nylon fabrics. The effects of extraction solvents on the reflectance, K/S value, and color properties of the dyed fabrics were investigated. Wash/dry cleaning and light colorfastness were evaluated. Reflectance curves of cotton, ramie, viscose rayon, and silk fabrics dyed with red colorants extracted by $K_{2}CO_{3}$ solution were similar, showing the maximum absorption at 520nm, to that of the dyed fabrics with red colorants extracted by ash solution. The reflectance curves of wool and nylon fabrics were different, showing the maximum absorption at 400nm. K/S values of dyed fabrics with red colorants extracted by $K_{2}CO_{3}$ solution were higher than that by ash solution with the exception of nylon. $L^{*},\;a^{*},\;b^{*}$, and $C^{*}$ of the dyed fabrics with red colorants extracted by $K_{2}CO_{3}$ solution were higher than that by ash solution except for $L^{*}$ of nylon and $b^{*}$ of viscose rayon. Color difference(${{\Delta}E}^*$) of the dyed fabrics between ash solution and $K_{2}CO_{3}$ solution increased in the order named as cotton, silk, ramie, viscose rayon, wool, and nylon. Regardless of extraction solvents, safflower red colorants produced RP color on cotton, ramie, and nylon, R color on viscose rayon and silk, and YR color on wool. Wash/dry cleaning fastness of the dyed fabrics was high above 3/4 rating but light fastness was very poor. It is considered that the use of $K_{2}CO_{3}$ solution instead of the traditional ash solution would be more effective in terms of color reproducibility and extraction process.

• Korean Journal of Food Science and Technology
• /
• v.52 no.4
• /
• pp.333-341
• /
• 2020

This study aimed at comparing the antioxidant activity of premature mandarin (PM) vinegars by varying harvest periods (July, August, and September) and raw material conditions (PM fruit, PMF; PM fruit with 10% dried Citri Unshius Pericarpium Immaturus (CUPI), PMF-D, and PM fruit with 10% roasted CUPI, PMF-R). We found that the PM harvested in July exhibited the highest phenol content. Meanwhile, the July and August harvests showed stronger DPPH radical scavenging and reducing power. The phenol content of PMF-R vinegar was 0.62±0.02 ㎍ GAE/mL, more than two times higher than that of PMF vinegar. The DPPH radical scavenging capacity and reducing power were the highest in the PMF-R vinegar, at 4.71±0.07 and 7.47±0.28 nL/mL, respectively. Therefore, it could be expected that PM vinegar prepared by adding roasted CUPI and harvested in July would exhibit high antioxidant activity and could be used as functional vinegar.

• Horticultural Science & Technology
• /
• v.31 no.2
• /
• pp.186-193
• /
• 2013

Potential of consumer unit packaging was investigated for quality maintenance during export simulation in king oyster mushrooms (Pleurotus eryngii). Mushrooms were harvested in late May, precooled to $4^{\circ}C$ within 6 hours, and then packaged for shipping in two ways: 2 kg bulk packaging in a polyethylene (PE) bag or three types of unit packaging methods such as 400 g in polypropylene film bag (PPB), 200 g on styrofoam tray + PE shrinkage film wrapping (STW), and 200 g in polyethylene terephthalate (PET) containers (PETC). For local distribution of bulk-packaged commodity, mushrooms were sorted again and packaged into 3 consumer units in the same way as for the initial shipping packages. Simulation of refrigerated container shipping was performed in a walk-in type pilot storage at $0.5^{\circ}C$ for 5 weeks, while local marketing simulation was carried out on the shelf at $7^{\circ}C$ for 7 days. During the shipment simulation, creation of modified atmosphere (MA) was substantial in 2 kg bulk packages with low $O_2$ below 2% and high $CO_2$ over 15% whereas, in PPB and PETC unit packages, relatively higher $O_2$ concentrations were observed. On the shelf at $7^{\circ}C$, $CO_2$ concentrations rapidly increased in PPB and PETC packages despite the short marketing period. Overall marketability evaluated by off-flavor, browning, and texture rating was maintained at excellent level when 2 kg bulk packaging in PE or unit packaging in PPB and PETC were used for shipment. In contrast, establishment of MA was very slight in STW packages during shipment and local distribution resulting in poor quality after export simulation. The results suggested that shipment using adequate consumer unit packaging is more practical and economically beneficial than using bulk packaging in the export program consisting of 5-week shipment and 7-day local distribution.

• Journal of Internet Computing and Services
• /
• v.18 no.1
• /
• pp.77-88
• /
• 2017

Recently, with the advent of knowledge based society where information and knowledge make values, patents which are the representative form of intellectual property have become important, and the number of the patents follows growing trends. Thus, it needs to classify the patents depending on the technological topic of the invention appropriately in order to use a vast amount of the patent information effectively. IPC (International Patent Classification) is widely used for this situation. Researches about IPC automatic classification have been studied using data mining and machine learning algorithms to improve current IPC classification task which categorizes patent documents by hand. However, most of the previous researches have focused on applying various existing machine learning methods to the patent documents rather than considering on the characteristics of the data or the structure of patent documents. In this paper, therefore, we propose to use two structural fields, technical field and background, considered as having impacts on the patent classification, where the two field are selected by applying of the characteristics of patent documents and the role of the structural fields. We also construct multi-label classification model to reflect what a patent document could have multiple IPCs. Furthermore, we propose a method to classify patent documents at the IPC subclass level comprised of 630 categories so that we investigate the possibility of applying the IPC multi-label classification model into the real field. The effect of structural fields of patent documents are examined using 564,793 registered patents in Korea, and 87.2% precision is obtained in the case of using title, abstract, claims, technical field and background. From this sequence, we verify that the technical field and background have an important role in improving the precision of IPC multi-label classification in IPC subclass level.

• Journal of Animal Environmental Science
• /
• v.15 no.3
• /
• pp.217-224
• /
• 2009

The pig slurry is one of important fertilizer source for production of crops in recent years, but it has many controversial points of utilization such as offensive odor, lack of spread equipment and farmland possession, respectively. This study was carried out in order to remove water pollutants and malodor of pig slurry using biofiltration system. The biofiltration system consists of pig slurry separator, mixing shift and attached blade for sawdust or ricehull, air injection nozzle and outlet for pig slurry and sawdust or ricehull. The characteristics pH, $BOD_5$ (Biochemical Oxygen Demand), $COD_{Mn}$ (Chemical Oxygen Demand), SS (Suspended Solid), T-N (Total Nitrogen), T-P (Total Phosphorus) of the untreated pig slurry used in this study were 7.2, 34,450, 24,604, 71,000, 4,194, $1,631\;ml/{\ell}$, respectively. The $NH_3$ (Ammonia) and $H_2S$(Hydrogen Sulfide) concentration were 70.0, 9.6 ppm, respectively. The initial total microorganisms of pig slurry were $5.0{\times}10^3\;cfu/ml$, and Salmonella, Bacillus were $5.8{\times}10^2$, $1.1{\times}10^3\;cfu/ml$, respectively. The filtration system was very effective on removal of water pollutants of pig slurry. The removal efficiency of the offensive odor of ammonia and hydrogen sulfide in sawdust was higher than those of ricehull. The total microorganisms and bacillus of pig slurry are on the increase by sawdust and ricehull, but Salmonella showed a tendency to decrease in number after that time. Accordingly, the filtration system was very effective to produce a good quality pig slurry.