• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.329-339
• /
• 2002

In ship operation the consequency of roll motions can seriously degrade the performance of mechanical and personnel effectiveness. So many studies for the roll stabilization control system design have been performed and very good results have been achieved. In many studies, the stabilizing fins are used. Recently rudders, which have been extensively modified, have been used to exclusively to stabilize the roll. This paper examines the two-degree-of-freedom servosystem design technique to synthesize the yaw control system which achieves the course keeping object of the ship and the H$_{\infty}$ control approach to suppress the roll motion, respectively.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.27 no.6
• /
• pp.832-838
• /
• 2021

Recently, reports of marine accidents of small fishing vessels less than 10 tons have been increasing. In this study, the characteristics of the motion response in regular waves were analyzed using computations for these ships. Small vessels less than 10 tons are classified by size and used for marine accident investigations. Therefore, the motion response analysis was performed on three small fishing vessels of different sizes. In the case of the head sea, it was confirmed that as the speed of the vessel increased in the long wavelength region, the motion responses of heave and pitch became large. The motion response of the smallest 3-ton fishing vessel was greater than that of the other sizes of fishing vessels. The maximum value of the roll motion shifted to the long wavelength region as the speed gradually increased in the bow sea, regardless of the size of the ship. In all the three small fishing vessels, it was found that the roll motion was the greatest at 15 knots, the highest speed in both bow and beam seas. When sailing in the head sea and bow sea conditions, lowering the speed is one of the effective approaches to reduce the effects of the vertical and lateral plane motions. The roll motion caused by the beam wave showed a tendency to increase rapidly only at a specific wavelength regardless of the speed and the size of the vessel. It was confirmed that the roll motion was significantly reduced with forward speed in the stern wave compared to the bow wave. As there is a specific region where the maximum value of the hull motion response appears depending on the size and speed of the ship, an operation method that can minimize the effect of this motion should be considered and implemented.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.3
• /
• pp.71-82
• /
• 1999

Irregular motions of nonlinear dynamic system are the result of an intrinsic characteristics that the system have, and sometimes occur unpredictable large motion. For a ship in a regular seaway, the capsizing occur because of this unexpectable motion. So, from the safety's point of view, nonlinear ship motions should be treated carefully. In this study, stable and unstable regions are investigated firstly under the variation of a control external force. Secondly, we consider the attractors to know how ship motions of the stable region that does not undergo capsizing change. Thirdly, bifurcation diagram is considered to study the range in detail where nonlinear chaotic motions are occurred.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.17 no.4
• /
• pp.39-45
• /
• 1980

내항성이 우수한 선형을 개발하기 위해서는 초기설계단계에서 이미 그 배의 해상에서의 거동을 예측할 수 있어야만 한다. 이 보고서에서는 임의의 입사각을 갖는 규칙파중을 항주하는 선박이 겪게 되는 동요중에서 횡동요, 수평동요 그리고 선수동요의 연성운동방정식의 해를 Tassi-Takaki가 수정한 스트립이론을 적용하여 해석하였다. 제15차 ITTC의 내항성 위원회의 보고서에서 발표된 콘테이너선형에 대한 결과와 똑같이 선형에 대해 본 프로그램을 사용하여 계산한 수평동요, 횡동요 그리고 선수동요의 운동응답을 비교하여 보았으며, 상당히 만족스러운 결과를 얻었다.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.11 no.1 s.22
• /
• pp.23-28
• /
• 2005

We have investigated the usefulness cf active stabilizing system to reduce ship rolling under disturbances, using varying reaction cf the flaps. In the proposed anti-rolling system for a ship, the flaps as the actuator are installed on the stem to reject rolling motion induced by disturbances like wave. The action induced by flaps which depends on power of disturbances am take the ship balance. Especially, in this study we identify the controlled system under the undefined system structure using spectral analysis and experimental studies. Based on these informations, we design the controller to evaluate the usefulness of the proposed system.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.6
• /
• pp.796-802
• /
• 2018

The effects of inner liquid sloshing on vessel motions are a well-known factor. It was investigated experimentally and numerically. In this regard, the study of many efforts to reduce natural phenomena of vessel motions by adopting special devices especially for roll motions. Among many devices, inserting baffles in the inner liquid tank is very common. In this study, one investigated the vessel motions with inner sloshing tanks with baffles inside. For the numerical simulation, one employed a dynamically coupled program between boundary-element-method-based vessel motion analysis program and a particle-based computational fluid dynamics program. Comparing corresponding experimental results validated the dynamically coupled program. The validated coupled program was used to simulate vessel motions, including sloshing effects with various lengths of inner baffles. The simulation results show that not only the filling ratio of inner liquid, but also the length of clearance due to baffles influenced the vessel motions. The significant point of this study was that the natural frequency of vessel motions can be maintained irrespective of the amount of filling ratio through adjustment of the clearance. In a future study, the effects of various numbers of baffles with various clearances would be conducted to percuss the possibility of vessel motion control with inner liquid sloshing effects.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.2
• /
• pp.131-138
• /
• 2019

This study focused on the roll motion characteristics of a two-dimensional (2D) rectangular floating structure under regular beam sea conditions. An experiment was conducted in a 2D wave tank for a roll free decay test in calm water and the roll motion in a range of regular waves with and without heave motion to investigate the motion response and heave influence on the roll motion. A numerical study was carried out using Reynolds-averaged Navier Stokes (RANS)-based CFD simulations. A grid convergence test was conducted to accurately capture the wave condition on the free surface based on the overset mesh and wave forcing method. It was found in the roll free decay test that the numerical results agreed well with the experimental results for the natural roll period and roll damping coefficient. It was also observed that the heave motion had an impact on the roll motion, and the responses of the heave and roll motion from the CFD simulations were in reasonable agreement with those from the experiment.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.7
• /
• pp.1244-1251
• /
• 2022

Marine accidents due to a loss of stability, have been gradually increasing over the last decade. Measures must be taken on the roll reduction of a ship. Amongst the measures, building an anti-roll tank in a ship is recognized as the most simple and effective way to reduce the roll motion. Therefore, this study aims to develop a computational model for a U-tube type anti-roll tank and to validate it by experiment. In particular, to validate the developed computational model, the height of the free surface in the tank was measured in the experiment. To develop a computational model, the mesh dependency test was carried out. Further, the effects of a turbulence model, time step size, and the number of iterations on the numerical solution were analyzed. In summary, a U-tube type anti-roll tank simulation had to be performed accurately with conditions of a realizable k-𝜖 turbulence model, 10^-2s time step size, and 15 iterations. In validation, the two cases of measured data from the experiment were compared with the numerical results. In the present study, STAR-CCM+ (ver. 17.02), a RANS-based commercial solver was used.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.05a
• /
• pp.1099-1100
• /
• 2012

• Journal of Navigation and Port Research
• /
• v.42 no.6
• /
• pp.395-405
• /
• 2018

Seakeeping safety module in Korean e-Navigation system is one of the ship remote monitoring services that is employed to ensure the safety of ships by monitoring the ship's real time performance and providing a warning in advance when the abnormal conditions are encountered in seakeeping performance. In general, seakeeping performance has been evaluated by simulating ship motion analysis under specific conditions for its design. However, due to restriction of computation time, it is not realistic to perform simulations to evaluate seakeeping performance under real-time operation conditions. This study aims to introduce a reasonable and faster method to predict a ship's roll motion which is one of the factors used to evaluate a ship's seakeeping performance by using a machine learning-based surrogate model. Through the application of various learning techniques and sampling conditions on training data, it was observed that the difference of roll motion between a given surrogate model and motion analysis was within 1%. Therefore, it can be concluded that this method can be useful to evaluate the seakeeping performance of a ship in real-time operation.