• Journal of Bio-Environment Control
• /
• v.10 no.4
• /
• pp.244-250
• /
• 2001

This study was conducted to determine the change in freezing tolerance of Chinese cabbage (Brassica campestris L. ssp. penkinensis). Four-week old seedlings grown in a greenhouse at $25^{\circ}C$$\pm$0.5 were transferred to 5, 10 or 15$^{\circ}C$ condition for acclimation for one day, and then transferred to a lethal temperature of -3$^{\circ}C$ condition. Optimal acclimation temperatures were 5$^{\circ}C$ and 1$0^{\circ}C$. Freezing tolerance of leaf tissues was investigated during a week-long cold stress. Development of freezing tolerance was shown by survival ratio, and amounts of total RNA, soluble protein and soluble sugar. LT$_{50}$ value increased from -3 to -4$^{\circ}C$ after 5 days acclimation at 5 or 1$0^{\circ}C$, and this was considered to be the first indication of enhanced freezing tolerance. Plants, cold acclimated for five days, reached to a survival ratio of 60%. This increase in freezing tolerance was found to be associated with the increased levels of total RNA, soluble sugar and soluble protein. These metabolic changes imply the association of adjustment of growth and cell metabolism with low temperatures at the beginning of cold acclimation in chinese cabbage.e.

• The Journal of the Acoustical Society of Korea
• /
• v.30 no.2
• /
• pp.63-72
• /
• 2011

Since the detection probability is critically dependent on the target strength (TS) in active sonar and on the radiated noise level (RNL) in passive sonar, the acoustic materials for echo reduction (ER) and transmission loss (TL) are widely used for the stealth of underwater targets. In this paper, a measurement system based on the small water tank, for the frequency range of greater than 30 kHz, is developed and verified using reference targets. In order to design the water tank and the geometry of test samples, a program is developed to calculate the arrival time of interfering signals due to the reflection from water tank walls and also due to the diffraction from the edge of the test samples. Considering all the interfering signals, an optimal experimental configuration for water tank and test samples is designed and used throughout the experiment. Next, the signal processing algorithms to estimate ER and TL are developed based on the measured propagation loss reflecting the geometric spreading characteristics of the transducer. Finally, a set of reference targets such as aluminium plate and perfectly reflecting plate are used in a small water tank to verify the developed measurement system.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.32 no.5
• /
• pp.487-493
• /
• 2014

A geographic survey, which requires much of working hours in the digital mapping process, is consisted with the complementary survey and the attribute survey of topography and topographic features, and depended on the field survey. In previous research, using the location-based image had been recommended for diminishing the workload of field survey and post processing. For this research, we have developed the hardware and software for gathering and processing the location-based images with referencing results from the previous research. Those Geographic surveys were performed using developed system on 1/5,000 map sheets for Si and Gun area, respectively. The results have been evaluated as the mobile geographic survey system were able to replace the large part of field survey, and also the working hours were decreased by 37.5% at Si area. However, the complementary survey was needed for the attributes of topography and topographic features that were occluded by the parked vehicles or located in the areas without entry of vehicles.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.2
• /
• pp.164-172
• /
• 2008

This paper presents the efficient localization of a mobile robot traveling on the floor with tags installed, using the spatial and temporal information acquired from passive RFID environment. Compared to previous research, the proposed localization method can reduce the position estimation error and also cut down the initial cost tag installation cost. Basically, it is assumed that a mobile robot is traveling over a series of straight line segments, each at a certain constant velocity, and that the number of tags sensed by a mobile robot at each sampling instant is at most one. First, the velocity and position estimation of a mobile robot starting from a known position, which is valid for all segments except the first one. Second, for the first segment in which the starting position is unknown, the velocity and position estimation is made possible by enforcing a mobile robot to traverse at least two tags at a constant velocity with the steering angle unchanged. Third, through experiments using our passive RFID localization system, the validity and performance of the mobile robot localization proposed in this paper is demonstrated.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.21 no.2
• /
• pp.80-85
• /
• 2017

Purpose The D530c have cadmium zinc telluride(CZT) detectors that are arranged focus on the heart. This structural characteristic allows for quicker imaging without rotation, but this is sensitive to patient movement and can affect the test results. The aim of this study is to optimize the image quality by reducing patient movement during the examination. Materials and Methods We analyzed the patients' movements, and performed various activities such as provided patient education about correct breathing techniques and avoiding patient movements, and created breathing correction tools to minimize patient movement during exam. The 70 patients who underwent myocardial perfusion SPECT with D530c in November 2016 were categorized as the group before the corrective steps. Another 70 patients who underwent the procedure with D530c from February 14, 2017 to February 21, 2017 were categorized as the improvement group. Images acquired during stress and at rest were compared and analyzed by measuring the durations of heart movements over certain distances (4 mm, 8 mm, 12 mm, or more) noted on the x-, y-, and zaxes. Results After the activities, the durations of heart movements decreased in the images acquired both under stress and at rest. In particular, there were no large motions greater than 12 mm recorded in the stress images after the improvement. There was a significant difference (p<0.005) in the 4-mm and 8-mm fluctuations on the X-axis and the 8-mm fluctuations on the Z axis in the stress images, but there was no significant difference (p>0.005) in the other stress and rest intervals. Conclusion The decrease in the time of motion occurrence due to the 4 mm fluctuation distance that can occur through breathing can be understood as a result of the breathing being corrected through training and motion prevention tools. It is expected that the image quality will be improved by reducing the occurrence time according to the variation distance of 8 mm or 12 mm, which is expected as the actual movement of the patient other than the breathing.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.6C
• /
• pp.505-511
• /
• 2008

The global navigation satellite system (GNSS) is using a direct sequence/spread spectrum (DS/SS) modulation. In order to recover the information data, the DS/SS system first performs a two-step synchronization process: acquisition and tracking. The acquisition process adjusts the phase difference between the received and locally generated acquisition sequences within ${\pm}T_c/2$ or less, where $T_c$ is the chip period. The tracking process performs fine synchronization. In this paper, we focus on the tracking issue. The single delta delay locked loop($\Delta$-DLL) is the optimal tracking scheme for a GNSS in the absence of multipath signals, where $\Delta$ means the spacing between the early and late correlation time offset. In the multipath environments, however, the $\Delta$-DLL suffers from huge estimation bias(denoted by $\beta$) caused by distorted correlation values. Although some modified schemes such as a $\Delta$-DLL with a narrow $\Delta$ and a double delta DLL (${\Delta}^{(2)}$-DLL) were proposed to reduce the estimation bias, they cannot remove the estimation bias completely and need more accurate acquisition process. This paper proposes a novel tracking scheme that can dramatically reduce the estimation bias, using the maximum slope change among the correlation outputs.

• The KIPS Transactions:PartA
• /
• v.13A no.1 s.98
• /
• pp.27-34
• /
• 2006

Designers should know CAD tool/license information such as available number of licenses or tools, types, and configuration methods to use CAD tools properly in their group. Usually, this information is provided by managers who administrate CAD tool and license servers in the specific design group. In the previous CAD tool/licenses sharing methods, designers have to get CAD tool/license information manually and setup the environments with their own hands. n a new designer comes into the design working group, the designer wastes unnecessary design time, because of these processes. As a result, designer's poductivity and utilization of CAD tools will decrease Besides, managers also waste their time and effort, since they should provide CAD tool/license information manually to each designer. In this paper, we present an automated scheme to share CAD tool/license information based on directory service. The proposed methods automate the communication processes between managers and designers that minimze unnecessary time to share CAD information. In addition, as this system maintains the consistency of CAD information automatically that remove the repeated work of managers and designers, it improves the enciency of sharing. Besides, it automates the license configuration steps using prof(y Last, we offer Executable Proxy which is proper for thin CAD application. We believe this scheme will reduce designers and managers' time and effort as well as maximize the utilization of CAD tools.

• Korean Journal of Remote Sensing
• /
• v.34 no.6_2
• /
• pp.1215-1227
• /
• 2018

Sea ice motion is an important factor for assessing change of sea ice because the motion affects to not only regional distribution of sea ice but also new ice growth and thickness of ice. This study presents an application of multi-temporal high-resolution optical satellites images obtained from Korea Multi-Purpose Satellite-2 (KOMPSAT-2) and Korea Multi-Purpose Satellite-3 (KOMPSAT-3) to measure sea ice motion using SIFT (Scale-Invariant Feature Transform), SURF (Speeded Up Robust Features) and ORB (Oriented FAST and Rotated BRIEF) feature tracking techniques. In order to use satellite images from two different sensors, spatial and radiometric resolution were adjusted during pre-processing steps, and then the feature tracking techniques were applied to the pre-processed images. The matched features extracted from the SIFT showed even distribution across whole image, however the matched features extracted from the SURF showed condensed distribution of features around boundary between ice and ocean, and this regionally biased distribution became more prominent in the matched features extracted from the ORB. The processing time of the feature tracking was decreased in order of SIFT, SURF and ORB techniques. Although number of the matched features from the ORB was decreased as 59.8% compared with the result from the SIFT, the processing time was decreased as 8.7% compared with the result from the SIFT, therefore the ORB technique is more suitable for fast measurement of sea ice motion.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2019.05a
• /
• pp.344-348
• /
• 2019

우리나라는 전 국토의 70%가 산지이고 하천경사가 다른 나라에 비해 상대적으로 급하여 홍수 관리에 매우 불리한 조건을 가지고 있으며, 특히 홍수기간의 집중호우 및 돌발홍수는 인명과 재산의 막대한 피해를 입히고 있다. 최근은 기후변화로 인하여 극심한 홍수, 가뭄 등 재해의 발생빈도가 증가하는 추세로 기후변화의 영향을 최소화할 수 있는 수재해 방재관리가 필요한 상황이다. 중 대하천의 경우에는 비교적 수재해 방재관리가 잘 이루어지고 있으나, 소하천(일부 중하천 포함)의 경우에는 취약한 구조를 보이고 있다. 특히 홍수기간(7월~9월)의 인명과 재산의 피해는 주로 소하천 위주로 발생하고 있으며, 사전 사후의 체계적인 대응이 이루어지지 못하고 있다. 수재해 방재관리를 위해서는 일차적으로 수문자료의 획득에 있으며, 그 이후 해당유역에 적합한 수재해 대응을 위한 체계적인 방법론과 방재시스템 개발 운영이 수반되어야 안전한 방재관리를 할 수 있다. 따라서 수재해 방재관리 체계를 구축하기 위해서는 중 소규모 유역 단위를 대상으로 지속적이고 신뢰성 있는 자료의 획득과 축적이 중요하므로 중 소규모 유역 단위의 대표성 있는 시험유역의 운영은 매우 의미가 있다고 볼 수 있다. 본 논문에서는 한국건설기술연구원에서 운영하는 차탄천 시험유역(유역면적 $190.64km^2$, 유로경사 0.96%, 경기도 연천군 소재)의 신뢰성 높은 2018년 관측자료를 이용하여 강우특성, 유출특성, 증발산량 등 수문특성을 분석하였으며, 과거 관측결과와 비교하였다. 강우특성 분석으로는 호우사상 분리, 주요 호우사상 분석, 지속기간별 최대강우량, 시간분포 등이 있다. 2018년은 2017년보다 최대 강우지속기간은 적게, 평균 강우지속기간은 크게, 최대 강우강도는 크게, 평균 강우강도는 적게 나타나는 호우의 특징을 보이고 있다. 2018년 지속기간별 최대강우량의 경우 지속기간 1시간까지는 2017년과 유사한 패턴을 보이나 그 이후는 많은 강우량을 보인다. 2018년의 하천유출률은 총강우량 대비 43.3%(장진교, 유역출구)와 70.3% (보막교, 중간소유역)로 2017년의 장진교(53.1%)와 보막교(60.4%)와는 차이를 보인다. 강우-유출특성 분석결과 연간 총강우량의 증가로 산지가 발달한 보막교는 9.9%의 증가가 있었지만 장진교는 오히려 9.8%의 감소가 있었다. 동일한 유역에서의 하천유출량의 차이는 2개 유역간 강우량 차이(96.1mm)와 토지이용(중 하류부농경지 발달)의 차이에 기인한다고 볼 수 있다. 그리고 2018년의 증발산량은 총강우량 대비 장진교(유역출구)는 32.3%로 2017년 장진교의 38.4%보다는 감소한 값을 보이나 2018년의 증발산량은 424.8mm, 2017년은 427.4mm로 양적의 차이는 거의 없는 것으로 분석되었다. 이와 같이 산정된 수문자료는 수재해 방재와 유역의 물순환 과정 규명을 위한 기초자료로 매우 유용하게 활용되므로 지속적인 시험유역의 운영은 매우 필요하다.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.7
• /
• pp.1059-1063
• /
• 2005

In the absence of organic solvent, di- and mono-acylglycerol enriched functional oil was produced by lipase-catalyzed glycerolysis in a stirred tank batch reactor. After glycerolysis for 48 hr, functional oil consisted of $47.1\%\;TAG,\;33.6\%\;DAG,\;and\;18.7\%$ MAG. In MAG and DAG, docosahexaenoic acid was found as $10.7\%\;and\;8.1\%$, respectively. During the reaction, total tocopherol content decreased, and $0.065\%$ tocopherols were existed in the functional oil produced after 48hr reaction.