• Journal of Advanced Navigation Technology
• /
• v.27 no.3
• /
• pp.255-261
• /
• 2023

A main purpose of this research was to analyze environmental factors to influence helicopter accidents contrary to the fact that the almost 80% of helicopter accidents happened due to pilots' human errors. There have been about 14 helicopter accidents in civil aviation sector last decade. It is noteworthy that nine of 14 accidents happened during the external sling load operation. Moreover, there is no law or regulation which could cover the helicopter external sling load operation or human external cargo in Korea. In this paper, it was analyzed the training and education regulations regarding helicopter external sling load operation or human external cargo in regulations of FAA and EASA, Based on analyzing and comparing the FAR part 133 and domestic aviation law (aviation safety act and flight safety regulations), it was found out the implication how to apply helicopter type rating for external sling load operation and human external cargo operation. To sum up, this paper expect central government should cooperate and amend aviation law which apply external sling load operation and external cargo to establish sound safety culture in Korea.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.1
• /
• pp.66-76
• /
• 2016

Determination of type of a vehicle is being used in various areas such as collecting tolls, collecting statistical traffic data and traffic prognosis. Because most of the vehicle type classification systems depend on vehicle length indirectly or directly, highly reliable automatic vehicle length measurement system is crucial for them. This study makes use of a pencil beam laser rangemeter and devises a mechanical device which rotates the laser rangemeter. The implemented system measures the range between a point and the laser rangemeter then indicates it as a spherical coordinate. We obtain several silhouettes of cross section of the vehicle, the rate of change of the silhouettes, signs of the rates then squares the rates to apply cell averaging constant false alarm rate (CA-CFAR) technique to find out where the border is between the vehicle and the background. Using the border and trigonometry, we calculated the length of the vehicle and confirmed that the calculated vehicle length is about 94% of actual length.

• Journal of Korea Port Economic Association
• /
• v.29 no.4
• /
• pp.1-25
• /
• 2013

The purpose of this paper is to estimate economic benefits for the investment of railway transshipment system with non-powered turntable. The freight transport by railway can have decided advantages over trucks in terms of energy efficiency, emissions and cost for certain freight movements, just as transportation in the metropolitan region can have great advantages over driving truck. But the freight transport by truck should gain significant mobility benefits from a freight railway system. Thus, the railway transshipment system with non-powered turntable which is coupled railway transport advantages with load transport advantages has been developed and used in the european countries. This research has conducted the empirical analysis, by calculating the investment of railway transshipment system with non-powered turntable. The key factor for the economic benefits for the non-powered turntable is the utilizing throughputs. This demand is influenced by the throughput in the railway transshipment system. The main results of this paper are as follows: railway transshipment system with non-powered turntable does not have economic benefit for investment. We recommend that the plan for investment has to be considered the modification.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.2
• /
• pp.109-123
• /
• 2009

The aim of the study was to assess the influence of insertion torque of bone quality and to compare axial force, moment and von Mises stress using finite element analysis of plastoelastic property for bone stress and strain by dividing bone quality to its thickness of cortical bone, density of trabecular bone and existence of lower cortical bone when implant inserted to mandibular premolar region. The $Br{\aa}nemark$ MKIII. RP implant and cylindrical bone finite model were designed as cortical bone at upper border and trabecular bone below the cortical bone. 7 models were made according to thickness of cortical bone, density of trabecular bone and bicortical anchorage and von Mises stress, axial force and moment were compared by running time. Dividing the insertion time, it seemed 300msec that inferior border of implant flange impinged the upper border of bone, 550msec that implant flange placed in middle of upper border and 800msec that superior border of implant flange was at the same level as bone surface. The maximum axial force peak was at about 500msec, and maximum moment peak was at about 800msec. The correlation of von Mises stress distribution was seen at both peak level. The following findings were appeared by the study which compared the axial force by its each area. The axial force was measured highest when $Br{\aa}nemark$ MKIII implant flange inserts the cortical bone. And maximal moment was measured highest after axial force suddenly decreased when the flange impinged at upper border and the concentration of von Mises stress distribution was at the same site. When implant was placed, the axial force and moment was measured high as the cortical bone got thicker and the force concentrated at the cortical bone site. The influence of density in trabecular bone to axial force was less when cortical bone was 1.5 mm thick but it might be more affected when the thickness was 0.5 mm. The total axial force with bicortical anchorage, was similar when upper border thickness was the same. But at the lower border the axial force of bicortical model was higher than that of monocortical model. Within the limitation of this FEA study, the insertion torque was most affected by the thickness of cortical bone when it was placed the $Br{\aa}nemark$ MKIII implant in premolar region of mandible.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.49-49
• /
• 2009

마찰교반접합법은 특정한 회전수로 회전하는 용접 툴을 이용하여 접합하고자 하는 피접합재의 맞댄면에 삽입시킨 후 툴을 이동시키거나 혹은 시편을 견고하게 고정시킨 장치(backing plate)가 움직여 고상 상태에서 접합이 이루어진다. 알루미늄, 마그네슘 등 비교적 융점이 낮은 저융점 재료의 재료에 처음 적용이 되어 많은 연구가 활발히 진행되었고 타 용접방법에 비해 우수한 접합특성을 나타내었다. 최근 이러한 마찰교반접합은 이러한 저융점 재료를 넘어서 스틸, 타이타늄, 니켈 등과 같은 고융점 재료 등에 대한 적용이 늘어나고 있다. 마찰교반접합을 이용하여 이러한 고융점 재료의 접합 경우 내마모성 및 내열성 등의 내구성이 갖추어진 툴과 이러한 툴을 냉각시킬 수 있는 냉각 장치 등이 필요로 하나 경제적 측면이나 접합부의 우수한 특성 등을 고려 할 때 그 적용 및 발전 가능성이 매우 높다고 볼 수 있다. 최근 무공해 연료로 각광받고 있는 액화천연가스 (LNG)의 수요가 급증함에 따라 LNG 저장탱크 소재로 널리 사용되고 있는 9% Ni강의 수요 또한 증가하고 있는 상황이다. 하지만 9% Ni 강은 극저온용 소재로 용접부의 저온인성 ($-196^{\circ}C$)이 가장 중요하기 때문에 저온인성을 확보하고자 Inconel 계나 Hastelloy계 등의 니켈 기 합금을 용접재료로 사용하고 있으나 이러한 용접재료는 가격이 매우 고가이며 또한 용접 후 용접부의 강도가 낮다는 문제가 제기되고 있다. 또한 LNG 탱크 제작시 사용되는 용접법은 GTAW, SAW 및 SMAW 이지만 국내에서는 주로 SMAW에 의존하고 있는 실정인 관계로 보다 더 경제적인 용접 프로세스의 적용 가능성이 검토되고 있는 상황이다. 본 연구에서는 마찰교반용접을 이용하여 두께 4mm의 9% Ni 강에 대해 맞대기 마찰교반접합을 실시하였다. 툴 회전 속도 및 접합 속도를 고정한 상태에서 접합을 실시 하였으며 접합 시 툴은 $Si_3N_4$로 제작된 툴을 사용하였다. 접합 후 외관상태 점검, 미세조직 관찰, 경도, 인장 강도 및 저은 충격 측정 등의 실험을 실시하였고, 이러한 결과를 이용하여 미세조직과 기계적 특성과의 관련성을 조사하였다.

• Journal of Oral Medicine and Pain
• /
• v.31 no.3
• /
• pp.255-263
• /
• 2006

Objectives: This article reported three patients developed anterior open bite seemed to be related to TMJ anterior disc dislocation without reduction(ADD WO R), but no evidence of condylar destructive or collapse and analyzed the craniofacial skeletal structure by means of cephalometric analysis. Results: All patients suddenly developed a centric relation/centric occlusion discrepancy, an increased overjet and an anterior open bite following ADD WO R. All patients had Angle's Class I occlusion and shallow bite, but they had skeletally Class III and Class II pattern and all were vertically significant hyperdivergent type. Conclusions: These 3 patients had characteristics of common facial morphology including:(1)Angle classification Class I and shallow bite,(2)high mandibular plane angle,(3)high gonial angle. Developed anterior open bite resulted from clockwise rotation of the mandible related TMJ ADD WO R, rather than a result from the eruption of posterior teeth. We hypothesize rotation may relate to attached direction of masticatory muscle.

• The korean journal of orthodontics
• /
• v.29 no.1 s.72
• /
• pp.113-127
• /
• 1999

The purpose of this study is to investigate the stability of counterclockwise rotation of mandible by sagittal split ramus osteotomy to correct the skeletal Class III malocclusion with anterior open bite. Twenty five skeletal Class III open bite patients(mean age 20.6 years) who were treated by the sagittal split ramus osteotonues with rigid fixation were examined in this study. Cephalometric radiographs were taken for each Patients Preoperative(T1), ewly Postoperative(T2), and late postoperative Period(T3). Mean postoperative period was 8.0 months. Cephalometric analysis was done and data from T1, T2, and T3 were analyzed statistically by Paired t-test and Pearson correlation analysis. The following results were obtained. 1. Mandibular plane angle decreased $2.9^{\circ}$ and mandibular occlusal plane angle related to SN Plane decreased $2.7^{\circ}$ after orthognathic surgery(T2). At 6 months after orthognathic surgery(T3), mandibular plane angle increased $1.0^{\circ}$, but mandibular occlusal plane angle did not changed. 2. The amount of horizontal relapse long time after orthognathic surgery(T3) was 1.6 mm at B point and it was $22\%$ of the total posterior movements. There was no vertical relapse in the anterior facial height. 3. The related factor with horizontal relapse at late postoperative period was mandibular plane angle(p<0.01). The related factors with decreasing posterior facial height were amount of mandibular setback(p<0.01), increasing of mandibular ramus height(p<0.01), and decrease of the mandibular plane angle during operation(p<0.01). 4. There was no relationship between the amount of changes in mandibular occlusal plan angle during operation and the amount of relapse after surgery.

• Journal of Korean Society of Steel Construction
• /
• v.23 no.3
• /
• pp.261-273
• /
• 2011

Recently, the demands for steel frame are increasing because of the trend and due to the demand for bigger and higher buildings. In the analysis of typical steel frame, connections are based on the idealized fixed or pinned connection. A fixed connection assumes that the relative angle of each member before deformation is the same after the transformation. Therefore, the stiffener reinforces the connection to sufficient rigidity and stability of the panel zone. In the economical aspect, however, the necessity of connection that the stiffener reinforcement has omitted is increasing due to the excessive production as well as labor costs of connection. In contrast, pinned connection is assumed that bending moments between the beams and columns do not transfer to each member. This is easy to make in the plant and the construction is simple. However, the structural efficiency is reduced in pinned connection because connection cannot transfer moments. The introduction of this semirigid process can decide efficient cross-sectional dimensions that promote ease in the course of structural erection, as performed by members in the field-a call for safety in the entire frame. Therefore, foreign countries exert efforts to study the practical behavior and the results are applied to criterion. This paper analyzes the semirigid connection of domestic steel by design specifications of AISC/LRFD and make data bank that pertain to each steel. After wards, the results are compared to those of idealized connection; at the same time, this paper presents a design method that matches economic efficiency, end-fixity, and rotational stiffness.

• Composites Research
• /
• v.14 no.1
• /
• pp.47-56
• /
• 2001

In order to enhance high speed stability the composite air spindle system composed of a high modulus carbon fiber composite shaft, powder contained epoxy composite squirrel cage rotor and aluminum tool holder was designed and manufactured. For the optimal design of the composite air spindle system, the stacking sequence and thickness of the composite shaft were selected by considering the fundamental natural frequency and deformation of the system. The analysis gave results that the composite air spindle system had 36% higher natural frequency relative to a conventional air spindle system. The dynamic characteristics of the composite spindle system were compared with those of a conventional steel air spindle system. From the calculated and test results, it was concluded that the composite shaft and the power contained composite rotor were able to enhance the dynamic characteristics of the spindle system effectively due to the low inertia and high speific stiffness of the composite materials.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1994.10a
• /
• pp.73-79
• /
• 1994

(1) 진공청소기의 소음은 팬모타의 회전에 기인하는 유체소음과 진동소음이 주류를 이루며, 여기에 공기의 흡입과 배출에 따른 유체소음등이 복합되어 나타난다. (2) 진공청소기의 소음특성은 각 소음원들의 특성에 따라 주파수대역을 구분할 수 있으며, 기계적 진동음인 500Hz부근에서 peak를 보인다. (3) 소음의 저감을 위하여는 기존에 정립되어 있는 흡음, 차음, 감쇠, 방진, 유압유속감소 등의 기술을 종합적으로 활용하여 제한된 공간내에서 효과를 극대화할 수 있는 구조개발이 필요하며 본 연구에 적용하였다. (4) 본 연구의 '정음유로구조'는 차음효과, 유로길이 증가에 의한 감쇠효과, 흡음효과를 극대화할 수 있는 구조이다. (5) 팬모타의 진동모드는 회전축을 중심으로 원운동을 하며, 진동량은 흡입구와 뒷쪽 베어링부위가 가장 작으므로 회전축에 가까운 곳을 지지하는 것이 방진에 유리하다. (6) 본 구조에서 사용된 케이싱은 484Hz의 고유진동수 성분을 가지며 이는 모타와 공진할 우려가 있다. 이에 공진주파수 성분의 진동량이 가장 작은 전면과 후면의 중앙부를 지지하여 진동을 줄일 수 있었다. (7) 본체소음의 전반적인 저감에 따라 흡입구 등에서 발생하는 공기마찰소음의 영향이 상대적으로 커지며, 따라서 흡입구의 유선형 설계 및 누설소음의 흡음, 차폐 등의 역할이 중요한 관리 요소로 된다.