• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.23 no.1
• /
• pp.1-5
• /
• 1987

The authors carried out an experiment to determine the vertical opening of the midwater trawl, which is the same used in the former experiment in this series of studies. To determine the vertical opening of otter board and front weight, three fish finders were used. A 200 KHz fish finder set on board the research vessel was used to sound the depth of water. A transmitter of 50 KHz fish finder was set through the shoe plate of otter board to determine the height of otter board from the sea bed, and a transmitter of another 50 KHz fish finder was set downwardly on the net pendant right before the front weight to determine the height of weight from the sea bed. The depth of otter board and weight were calculated by subtract the height of those from the depth of water, respectively. To determine the vertical opening of mouth, a transmitter of net recorder was set on the head rope and the vertical opening of that to ground rope was directly read on the recording paper. The results obtained can be summarized as follows: 1. The rate of the depth of otter board to the length of warp was in the range of 0.44 to 0.25, and the depth was linearly shoaled about 5m per 0.1m/sec of the towing speed or per 20rpm of the main engine. The rate of the observed depth to the calculated depth of otter board was in the range of 0.92 to 0.080 with a decreasing tendancy in accordance with the increase of towing speed. 2. The depth of head rope was 2 to 3m deeper than that of otter board, and the vertical opening of net mouth was in the range of 22 to 19m, with a decreasing tendancy in accordance with the increase of towing speed, 3. The difference of depth between front weight and otter board was about 20m and 22m respectively in the length of warp 100m and 150m without distinct change in accordance with the towing speed. The depth of front weight was 2 to 3m shallower than that of ground rope. 4. The changing range of depth of head rope according to the revolution of main engine was about 4m per 20rpm.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.3
• /
• pp.175-179
• /
• 1979

One of the major problems in tile activated sludge system has been difficulty in separating the microbial solids from the treated effluent and in returning them to the aeration tank. Another problem has been the digestion of the excess activated sludge. In constrast, it has not been difficult to separate the microbial solids from the treated effluent from the biological fixed-film systems(RBC process, Trickling Filter, FAST process). These systems have also featured less sludge production. Recently, it was proposed to experiment with the RESMAS process in order to eliminate the settling tank and sludge concentration facilities and to reduce the quantity of excess sludge for final disposal. The effluent quality could be predicted by .the concept of the maximum accumulation capacity. However, the hydraulic characteristics of the screen media in the RESMAS reactor were not dynamic. The object of the present study is to evalute the sludge accumulation rate and effluent quality prediction in the REMSMAS process designed in the dynamic hydraulic structure. This process can eliminate the final sedimentation tank and sludge concentration tank needed in the RBC, CMAS, Trickling Filter and FAST processes. Also, the effluent quality is desirable to compare with other processes. It appeared that the value of the sludge holding capacity was higher than those of the RESMAS and FAST processes, and the periods of the critical operating time were proportional to the substrate hydraulic loadings.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.672-680
• /
• 2018

The opening angle of the duct cap assembly during the operation of a refrigerator ice dispenser was evaluated by transient structural analysis, and an improved design to maximize the opening angle was obtained. The opening angle of the existing design was found to be 78% of the upper limit. Several design modifications were proposed and analyzed to examine the effects of the design factors on the opening angle. As a result of the design modifications, the opening angle was improved by changing the lever material to a material with a high elastic modulus, moving the position of the support to the motor side, or increasing the lever shaft diameter. Considering the manufacturing cost of the new design, the design modification changing only the lever material was found to be the best because it does not require a change in the structure of the ice dispenser case. In conclusion, the opening angle can be improved by up to 95% of the upper limit value if the lever material is changed to an aluminum alloy. The methods and results presented in this study were found to be of great help in designing the duct cap assembly structure to facilitate the discharge of ice.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.12
• /
• pp.446-452
• /
• 2016

Recently, heat resistant super alloys (which are wear-resistant, corrosion-resistant, and heat-resistant), have been used as the basic structural material in offshore and petrochemical plants. On the other hand, making valves from very expensive, high heat-resistant alloys increases the production cost and decreases its market competitiveness. To solve these problems, the technique of overlaying only those that flow on the fluid has been used as an effective method. Nevertheless, because the former technique of overlaying the ball is performed manually, it takes too much time and perfect welding is difficult to perform. To solve this problem, this study developed a robot automation system that can make uniformly overlay welding of the ball for ball-valves. The system consists of a 6-axis welding robot with a welding torch and additional 2 axes for the rotation of positioner, the controller, and a robot path OLP (Off-Line Programming). The CAD drawing data was entered in the Off-line program to obtain the robot teaching point and drive source. Overlay welding paths were implemented using Matlab. Through an automated overlaying system that implemented the OLP, the productivity rose 2.58 times, as the amount of time required for work decreased from 88 hours to 41 hours.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.578-585
• /
• 2018

This paper proposes a design method for a 3-phase interior permanent magnet synchronous motor (IPMSM) and clamping force control method for an electro-mechanical brake (EMB) using co-simulation for a high-speed train (HST). A traditional pneumatic brake system needs much space for the compressor, brake reservoir, and air pipe. However, an EMB system uses up to 50% less space due to the use of a motor and electric wires for controlling the brake caliper. In addition, it can reduce the latency time for brake control because of the fast response and precise control. A train that has many brakes is advantageous for safety because of the control by sharing the braking force. In this paper, a driving method for a cam-shaft-type EMB is modeled. It is different from the ball-screw-type brakes that are widely used in automobiles. In addition, a co-simulation method is proposed using JMAG and Matlab/Simulink. The IPMSM was designed and analyzed with the JMAG tool, and the control system was simulated using Matlab/Simulink. The effectiveness of the co-simulation results of the mechanical clamping force and braking force was verified by comparison with the clamping force specifications of a HEMU-430X HST.

• Nuclear Engineering and Technology
• /
• v.13 no.4
• /
• pp.264-276
• /
• 1981

A simulation procedure which can represent time-dependent nuclear characteristics of TRIGA Mark-III reactor is developed. CITATION, a multi-group diffusion-depletion program, has been utilized as calculational tool. The group structure employed in this study consists of 7 groups: -3-fast and 4-thermal-which is conventionally utilized in TRIGA type reactor analysis. Three-dimensional nuclear characteristics are synthesized by combining results from two-dimensional plane calculation and two-dimensional cylinder calculation, since direct three-dimensional approach is not yet possible. An effort ia made to develope a method which can extract effective zone and group dependent bucklings by neutron diffusion theory rather than conventional zone and/or group independent Ducklings by neutron transport theory, since neutron leakage is quite high for small core such as research reactors. It is turned out that the method developed in this study gives satisfactory results. The calculation is performed under assumptions that all control rods are fully withdrawn, that no samples are inserted in the irradiation holes and that the core is located in the center of the reactor pool. Burnup-dependent variation of core excess reactivity, time dependent change of Xe-135 poisoning and reactivity worth of rotary specimen rack are calculated and compared with operation records. Neutron flux and power distribution as well as neutron spectrum in each irradiation .facility are presented.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.26 no.4
• /
• pp.429-435
• /
• 2020

Different methods are used for determining the output of engines to obtain the indicated horsepower by measuring the combustion pressure of cylinders, and to obtain the shaft horsepower by measuring the shaft torque. It is difficult to examine the shaft torque using the condition of the cylinder, and the most accurate method used for determining the combustion pressure involves examining the combustion state of the cylinder to evaluate the engine performance and analyze the combustion of the cylinder. During the measurement, the combustion pressure is the most important parameter used for accurately determining the cylinder angle because the cylinder pressure is indicated based on the angle of the crankshaft. In this study, an encoder was used as the crank angle sensor to measure the cylinder pressure on the generator engine of the actual operating ship. The reasons for the differences between the top dead center (TDC) recognized by the encoder (TDC_encoder) and the TDC recognized by the compression pressure (TDC_comp) were considered. The dif erences between the TDC_comp and TDC_encoder of the cylinders measured at idle running, 25 %, 50 %, and 60 % loads were analyzed to determine for the crankshaft production effect, the crankshaft torsion effect owing to the increased rotational resistance from the increased load, and the coupling damping effect between the engine and generator. It was confirmed that the TDC error occurred up to 3° crank angle as the load of the generator increased.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.74-74
• /
• 2011

본 연구에서는 중앙경간 54m, 교폭 4m의 사장교형식의 보도교로 측경간은 계단으로 이루어진 1경간 케이블교량을 대상으로 보행하중에 의한 수직진동을 제어하기 위해 제진장치(TMD)를 적용하기로 하고 실물 TMD의 설계 및 제작 그리고 설치 및 제어성능실험을 수행하였다. 우선 사장교형식의 교량. 그리고 1경간 교량이라는 점에서 상대적으로 감쇠율이 낮을 것으로 예측되었고 또한 54m의 경간장이 보행자가 가진 주파수에 근접한 고유진동수를 나타낼 것으로 사료되어 Eurocode 2 part 2(EC5-2)의 규준에 따라 1인 및 다수 보행하중에 의한 보도교의 발생가속도를 산출하였다. 이 경우 최대가속도는 다수의 보행자가 연속적으로 진행할 때 발생하였으며, 수직방향의 가속도가 사용성기준을 초과하는 것으로 나타났다. 또한 구조해석프로그램에 의한 고유치 해석결과, 보행하중의 주파수대역내에 진동모드가 존재하는 것으로 나타났다. 따라서 본 교량의 설계단계에 있어서 보행진동을 제어하기 위하여 유지관리가 용이한 수동형의 동조질량감쇠장치(Tuned Mass Damper)를 적용하기로 하였으며 TMD의 설계에서는 TMD의 제어목표를 만족시킬 수 있는 TMD의 가동질량(moving mass)을 우선적으로 결정하였고, 이로부터 Den Hartog의 제안식에 따라 TMD의 고유진동수비, 유효감쇠비를 산정하였다. 산정된 변수들을 이용하여 설계된 TMD는 현장설치 및 튜닝의 편의성을 고려하여 수평 외팔보형식으로 설계, 제작되었으며 제작된 TMD의 경우 회전축에 대해 질량, 스프링, 댐퍼의 중심거리를 조정함으로써 TMD의 진동수, 강성, 감쇠력을 상대적으로 매우 용이하게 조절할 수 있으며, 조정범위 또한 광범위하여 일반 TMD에 비해 현장설치시 대상구조물에 동조시키기가 용이하며, 작동시 마찰감쇠가 거의 없다는 장점이 있다. 현장설치전에 제작된 TMD를 대상으로 자유진동 시험을 통하여 질량의 중심거리, 스프링 크기 그리고 댐퍼의 설치유무를 각각 변화시키며 TMD의 자유진동 데이터를 취득하였다. 각각의 시험에서 얻어진 데이터로부터 스펙트럼해석을 통하여 고유진동수를 구하였고, 자유진동 파형으로 부터 감쇠비를 구하였다. TMD는 일반적으로 제어모드의 변형형상이 가장 큰 곳에 설치되었을 때 최대의 제진효과를 발휘할 수 있다. 그러나 현장여건상 설치가 불가능하거나 미관을 해치는 경우에는 가능한 범위 내에서 TMD 제어효율이 가장 크게 발휘할 수 있는 곳을 선택하여야 한다. 본 보도교의 경우, 중앙경간 중심부에서 가장 큰 모드변형형상을 나타내지만, 보도교의 상판 연결부 등에 따른 TMD 시공문제로 인하여 TMD 설치위치는 교량 중앙에서 양 방향으로 1.25m 떨어진 곳에 대칭으로 총 2기를 설치하기로 하였다. 일반적으로 TMD의 모든 설계변수는 구조물의 설계단계에서 수행된 구조해석결과에 근거하여 설정하므로 완공된 구조물, 즉 실제보도교의 동적특성을 계측하여 정확하게 진동수를 튜닝하여야 한다. 구조해석에 의한 보도교의 수직방향(TMD 작동방향) 고유진동수는 1.5225 Hz이며, 감쇠비는 규준에 의하여 0.6 %로 가정하였다. 그러나 이 값들은 구조해석모델 및 재료적 특성과 시공상의 오차에 의하여 실제와 다를 수 있으므로 현장계측에 의한 확인이 요구된다. 또한 TMD의 제진효율이 설계시의 목표대로 확보되었는지도 확인해야 하므로 현장튜닝 및 성능시험을 실시하였다. 보도교의 가진은 사전에 실시한 상시 미진동계측결과를 토대로 2Hz를 목표로 하여 인력가진실험을 수행하였고, 탁월진동 주파수는 1.9896Hz로 나타나 구조해석결과와 오차가 있음을 알 수 있다. 가진실험결과를 토대로 TMD의 진동수를 최적진동수비로 튜닝하고 인력가진 실험을 다시 실시하여 TMD의 진동제어성능을 검토하였다. TMD 튜닝 전, 후의 보도교 감쇠비를 비교한 결과, TMD를 설치함으로써 약 4.218%의 감쇠비 증가가 있음을 알 수 있다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.15 no.4
• /
• pp.45-54
• /
• 2011

A simple model for reinforced concrete shear walls with boundary elements is proposed, which is a macro-model composed of spring elements representing flexure and shear behaviors. The flexural behaviour is represented by vertical springs at the wall ends, where the moment strength and rotational capacity of the wall are based on section analysis. The shear behaviour is represented by a horizontal spring at the wall center, where the key parameters for the shear behavior are based on the flexural behaviour since the shear walls with boundary elements are governed by the flexure. The proposed model was prepared with the results of hysteretic tests of the shear walls, and then the reliability of the hysteretic rule and variables was investigated by nonlinear dynamic analyses. Using parametric study with nonlinear dynamic analyses, the effect of the variables on demand and capacity, which are major parameters in seismic performance evaluation, are investigated. Results show that the measured and calculated shear forces versus the shear distortion relationships are slightly different, but the global response is well simulated. Furthermore, the demand and capacity are also changed in a similar way to the change in the major parameters so that the proposed model may be appropriate for reinforced concrete shear walls with boundary elements.

• Journal of Korean Home Economics Education Association
• /
• v.22 no.2
• /
• pp.1-13
• /
• 2010

This study was planned to provide basic information to help teachers guide lookism-prone students in their home and school life, and to guide them in the unit relating to clothing in school curriculums. To carry out this experiment questionnaires were administered to 481 students in their first and second year in middle and high schools in Gwangju city. The questionnaires are composed of 3 themes; 'general matters', 'attitudes about and recognition of appearance management' and 'school adaptation'. The collected data was analyzed with Component analysis(Varimax rotation) and Cronbach's ${\alpha}$, T-test, one-way ANOVA, Duncan-test, Pearson's correlation analysis and multiple regression analysis using the SPSS WIN 14.0(Kr). The results of this study were as follows; 1. The more they managed their behavior relating to appearance and cleanliness, the better they felt their friendships. 2. The less they concentrated management relating to appearance, the better they felt about their relationships with their teachers. 3. The less they concentrated management relating to appearance but the more they managed cleanliness the easier they adjusted to school rules. 4. The less they pursued a trendy appearance but the more they managed cleanliness, the better they studied.