• Applied Chemistry for Engineering
• /
• v.7 no.1
• /
• pp.75-82
• /
• 1996

Acrylic acid was graft-copolymerized on polyethylene film in the presence of additives such as acid and $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ using peroxide grafting technique by ${\gamma}$-ray and electron beam, and the effect of $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ and acid on the grafting yield was evaluated. The grafting mechanism and the physical property of grafted films were also examined. The results showed that the inclusion of $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ in acidified acrylic acid grafting solution was extremely beneficial and led to a most unusual enhancement effect in the radiation grafting. In the other hand, inclusion of mineral acid in the grafting solution in the absence of $FeSO_4(NH_4)_2SO_4{\cdot}6H_2O$ could not lead to he suitable grafting reaction by the severe homopolymerization of acrylic acid. The addition of $H_2SO_4$, and HCl led to much higher grafting yield than $HNO_3$and $CH_3COOH$. It was shown that grafting yield of ${\gamma}$-ray irradiated-polyethylene was higher than that of electron beam irradiated polyethylene.

• Journal of the Korean Chemical Society
• /
• v.37 no.2
• /
• pp.249-254
• /
• 1993

N-p-nitrophenyl poly(m-phenylene isophthalamide) was obtained from treatment of poly(m-phenylene isophthalamide) with sodium hydride in dimethyl sulfoxide followed by the addition of 1-fluoro-4-nitrobenzene in 43 wt% yield. Its inherent viscosity was 0.606 g/cm${\cdot}$sec determined from a solution of 0.125 g of the above polymer dissolved in 25 ml of 98% sulfuric acid at $30^{\circ}C.$ In order to synthesize poly(m-phenylene isophthalamide), 1,3-phenylenediamine is allowed to react with isophthaloyl chloride in chloroform in the presence of triethylamine and added triethylamine hydrochloride. The value of inherent viscosity is 0.560 g/cm${\cdot}$sec measured at the same condition. The substitution ratio of N-p-nitrophenyl poly(m-phenylene isophthalamide) was to be 16.7∼47.0% by using the $^1H-NMR$ integration. When the higher inherent viscosity of poly(m-phenylene isophthalamide) was used, lower substitution ratio would be calculated.

• Air Cleaning Technology
• /
• v.17 no.4 s.67
• /
• pp.39-57
• /
• 2004

첨단산업으로 불리는 반도체, LCD, PDP, 유기EL(OLED) 등의 생산 공정은 고도의 청정상태를 요구하며, 때문에 이들의 생산공정 중 대부분이 클린룸 내에서 이루어진다. 클린룸 내에서의 주요공정은 크게 박막형성(Layering), 노광(Photo Lithography), 식각(Etching) 등 3가지 공정으로 나눌 수 있으며, 반도체 제조공정의 경우 특별히 도핑(Doping) 공정이 추가된다. 오염물질을 함유하는 클린룸 배기는 일반적으로 산, 알칼리, Toxic(PFCs, Flammable), VOC 등으로 분류하며, 각각의 배기는 각 배기특성에 맞는 오염제어 장치를 통해, 정화된 후, 대기로 방출된다. 산, 알칼리 배기는 일반적으로 최종 단계에서 중앙집중식 습식스크러버에 의해 흡수, 중화 처리되며, VOC의 경우 농축기(Concentrator) & 축열식 열 산화장치(RTO) 설비에 의해 연소 처리된다. 하지만 CVD공정으로부터의 배기가 주를 이루는 Toxic배기의 경우, 다량의 PFCs(과불소화합물) 가스를 함유하고 있는 이유로, 대부분 클린룸 내부에 P.O.U(Point of use) 처리장치가 설치되며, P.O.U에 의해 1차 처리된 후 최종적으로 중앙집중식 습식스크러버를 거쳐 대기로 방출된다. 알칼리배기의 주성분으로는 암모니아($NH_3$), HMDS (Hexa Methyl DiSilazane), TMAH (Tetra Methyl Ammonium Hydroxide), LGL, CD 등이며 흡수액에 황산(Sulfuric Acid)용액을 공급, 중화처리하고 있다. 탄소성분을 먹이로 하는 미생물의 번식에 의한 막힘 문제를 제외하고는 큰 문제가 없다. 하지만 Toxic배기 및 산배기의 경우 처리효율이, 가스흡수 이론에 의한 계산결과와 비교할 때, 매우 저조하게 나타나는 효율부족 현상을 겪고 있으며, 이는 잔여 PFCs 가스성분 및 반응에어로졸, 응축에어로졸 등의 영향으로 추정하고 있다. 최근 Toxic 배기의 경우, P.O.U 설비를 Burn & Wet type으로 변경하여, 배기 중 PFCs 및 반응에 에어로졸($SiO_2$)의 농도를 원천적으로 감소시키는 노력이 진행 중이다. 산배기의 경우, 산결로 현상에 의한, 응축에어로졸이 문제가 되고 있으나 내식열교환기(Anti-Corrosive Heat Exchanger), 하전액적스크러버 시스템(Charged Droplets Scrubber System), Wet ESP(Wet Electrostatic Procipitator) 등의 도입을 통해 문제해결을 위한 노력을 경주하고 있다.

• Applied Chemistry for Engineering
• /
• v.33 no.4
• /
• pp.381-385
• /
• 2022

It is very important to secure the adhesion durability between the base film and the conductive paste for the development of a sensor for detecting hazardous chemicals. In this study, an ester binder was used to improve the adhesive properties which can be a problem when applying the sensor to the cross cut 0B or 1B grade. This problem was found while evaluating the adhesive properties by coating the polyaniline/graphene nano plate (GNP) paste on the polyethylene terephthalate (PET) film. When 10 wt% or more of the ester-based binder was added, the cross cut grade to which the sensor can be applied was 3B or higher. It was confirmed that the excessive addition of the binder may affect the electrical properties of the conductive paste and actually decrease the reactivity to sulfuric acid. To improve the electrical property, a carbon black (CB) content was varied resulting in the optimum electrical property observed at 2 wt% of CB.

• New & Renewable Energy
• /
• v.19 no.1
• /
• pp.1-11
• /
• 2023

A large amount of carbon monoxide (CO) is generated in circulating fluidized bed combustion, the process whereby a hot cyclone separates unburned fuel. However, calcium sulfate (CaSO₄), when combined with a high CO content, can cause fouling on the surface of the steam tube installed inside the integrated recycle heat exchangers (INTREX). In this study, CaSO₄ decomposition was investigated using 0.2-3.2 vol.% CO and 1-3 vol.% oxygen (O₂) at 850℃ for 20 min in a lab-scale fluidized bed reactor. The results show that CaSO₄ decomposes into CaS and CaO when CO gas is supplied, and SO₂ emissions increase from 135 ppm to 1021 ppm with increasing CO concentration. However, the O₂ supply delayed SO₂ emissions because the reaction between CO and O₂ is faster than that of CaSO₄; nevertheless, when supplied with CaCO₃, the intermediate product, SO₂ was significantly released, regardless of the CO and O₂ supply. In addition, agglomerated solids and yellow sulfur power were observed after solid recovery, and the reactor distributor was corroded. Consequently, a sufficient O₂ supply is important and can prevent fouling formation on the INTREX surface by suppressing CaSO₄ degradation.

• Journal of Veterinary Clinics
• /
• v.31 no.3
• /
• pp.199-205
• /
• 2014

Acidosis conditions either acute or chronic following ingestion of excessive amounts of readily fermented carbohydrate are great production problems for goat in Bangladesh. This study designed to investigate the prevalence of lactic acidosis and then response to different therapeutic agents. For this purpose, 1,128 goat were examined at outdoor District Veterinary Hospital, Faridpur, Bangladseh for treatment of which 40 goats were found positive for lactic acidosis showing 3.55% prevalence of disease. The highest occurrence found in female (4.64%) of over 3 years age (4.64%) in indigenous goat (2.7%). For therapeutic assessment the forty affected goats were divided into four groups A, B, C and D comprising of 10 animals each. Group A were given magnesium hydroxide 8% w/v at 1 g/kg body weight orally. In group B magnesium hydroxide 8% w/v at a dose as group A combination with 7.5% sodium bicarbonate at the rate of 0.9 ml/Kg body weight intravenously administered. Goat in group D were treated with mixture of ginger, nuxvomica, sodium carbonate, cobalt sulphate, dried ferrous sulphate and thiamin mononitrate at the rate of 1 g/kg body weight orally. Goat of group C treated with combination drugs of group A, B and D. The rectal temperature, pulse rate, respiration rate, was performed before and after treatment. It was found that the highest recovery in group C with an average period of $21{\pm}1.8$ hours. It was concluded that lactic acidosis is a common disease of goats and its severity can be effectively reduced by using combination drugs.

• Journal of the Korean Society of Groundwater Environment
• /
• v.5 no.4
• /
• pp.177-191
• /
• 1998

For various kinds of waters including surface water, shallow groundwater (＜70 m deep) and deep groundwater (500∼810 m deep) from the Pungki area, an integrated study based on hydrochemical, multivariate statistical, thermodynamic, environmental isotopic (tritium, oxygen-hydrogen, carbon and sulfur), and mass-balance approaches was attempted to elucidate the hydrogeochemical and hydrologic characteristics of the groundwater system in the gneiss area. Shallow groundwaters are typified as the 'Ca-HCO$_3$'type with higher concentrations of Ca, Mg, SO$_4$and NO$_3$, whereas deep groundwaters are the 'Na-HCO$_3$'type with elevated concentrations of Na, Ba, Li, H$_2$S, F and Cl and are supersaturated with respect to calcite. The waters in the area are largely classified into two groups: 1) surface waters and most of shallow groundwaters, and 2) deep groundwaters and one sample of shallow groundwater. Seasonal compositional variations are recognized for the former. Multivariate statistical analysis indicates that three factors may explain about 86% of the compositional variations observed in deep groundwaters. These are: 1) plagioclase dissolution and calcite precipitation, 2) sulfate reduction, and 3) acid hydrolysis of hydroxyl-bearing minerals(mainly mica). By combining with results of thermodynamic calculation, four appropriate models of water/ rock interaction, each showing the dissolution of plagioclase, kaolinite and micas and the precipitation of calcite, illite, laumontite, chlorite and smectite, are proposed by mass balance modelling in order to explain the water quality of deep groundwaters. Oxygen-hydrogen isotope data indicate that deep groundwaters were originated from a local meteoric water recharged from distant, topograpically high mountainous region and underwent larger degrees of water/rock interaction during the regional deep circulation, whereas the shallow groundwaters were recharged from nearby, topograpically low region. Tritium data show that the recharge time was the pre-thermonuclear age for deep groundwaters (＜0.2 TU) but the post-thermonuclear age for shallow groundwaters (5.66∼7.79 TU). The $\delta$$\^$34/S values of dissolved sulfate indicate that high amounts of dissolved H$_2$S (up to 3.9 mg/1), a characteristic of deep groundwaters in this area, might be derived from the reduction of sulfate. The $\delta$$\^$13/C values of dissolved carbonates are controlled by not only the dissolution of carbonate minerals by dissolved soil CO$_2$(for shallow groundwaters) but also the reprecipitation of calcite (for deep groundwaters). An integrated model of the origin, flow and chemical evolution for the groundwaters in this area is proposed in this study.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.111-111
• /
• 2012

나노테크놀로지는 종래의 가공으로는 얻기 힘들었던 섬유가공 효과를 간단하게 할 수 있는 기술이다. 현재 각국의 기능성 나노 가공제를 섬유에 응용하는 나노 테크놀로지는 현재 공업 생산되고 있는 면, 모, 견 등의 천연섬유 및 polyester, Nylon 등의 합성섬유의 원단에 적용하는 데서 출발하고 있다. 이러한 나노기술은 기존의 설비와 물을 사용하는 것이 큰 특징이고, 특별한 기계장치가 필요하지 않으며, 소규모의 실험장비만 있어도 현장투입이 가능한 나노입자의 제조가 가능하기 때문에 대량생산이 용이하고 설비투자는 원칙적으로 필요하지 않는다. 또한, 나노입자의 분산을 제대로 시키면 그 사이즈가 빛의 가시광선 영역의 파장(400~800nm)에 비해 절반 수준이하 크기의 입자가 대부분을 차지하기 때문에 염색성, 태의 변화가 적어 앞으로 더욱더 나노테크놀로지에 의한 가공이 확대될 것이 예상된다. 특히 유 무기 하이브리드 재료는 용액상태에서 제조되기 때문에 용액 코팅공정의 적용이 가능하여 다양한 코팅에 적극적으로 활용되고 있다. 또한 코팅공정 온도가 상대적으로 낮아서, 유기물의 기능성 발현이 용이하며, 섬유가공에 그대로 적용이 가능하고, 섬유고분자와 내구성 있게 직접 결합이 되어 실용성이 높다 할 수 있다. 또한 나노졸의 형성 시, 혹은 나노졸에 기능성 물질을 첨가함으로서 나노졸과 기능성 물질을 복합화하여 섬유상에 부여하는 것도 가능하다. 최근에 실리카졸의 형성과 성장에 관한 연구는 졸-겔 기술의 발전과 해석 및 상용화에 집중되어 있다. 규산나트륨과 황산 또는 염산을 사용하여 실리카를 생성하는 공정은 tetraethoxysilane (($Si(OC_2H_5)_4$, (TEOS))를 이용하여 합성하는 방법과 달리 대량의 실리카를 경제적으로 생산하는데 방법으로 널리 연구되고 있지만, 많은 연구가 수행되었음에도 불구하고 실리카 졸의 특성, 성장, 제조에 대한 충분한 이해가 이루어 지지 않고 있어, 아직까지 나노크기의 입자를 제조하는 공정에 대해서는 경제성, 효율성, 품질의 균일성이 떨어지는 것이 현실이다. 따라서 본 연구에서는 앞서 연구된 졸-겔 합성기술과 저렴한 원료인 규산나트륨을 이용하여 보다 간단하고 경제적인 방법으로 고부가가치의 다양한 실리카 나노졸을 제조할 수 있는 연구를 하고자 하였다. 이를 위해 규산나트륨 수용액의 특성, 핵 생성에 필요한 규산나트륨 수용액의 산화반응 특성, 그리고 출발용액의 졸겔 반응을 기초로 하여 실리카 졸 형성에 대한 반응물질의 혼합방법, 반응온도, 반응물의 농도, pH등이 최종 실리카 나노졸 제품의 입자 크기와 모양 등에 미치는 영향을 조사하려고 하며 이를 토대로 다양한 크기와 특성을 가진 실리카 나노졸을 제조하였다.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.2
• /
• pp.151-157
• /
• 2005

A one-dimensional numerical model was developed to simulate vertical profiles of electron acceptors and their reduced species in benthic sediments. The model accounted for microbial degradation of organic matter and subsequent chemical reactions of interest using stoichiometric relationships. Depending on the dominant electron acceptors utilized by microorganisms, the benthic sediments were assumed to be vertically subdivided into six zones: (1) aerobic respiration, (2) denitrification, (3) manganese reduction, (4) iron reduction, (5) sulfate reduction, and (6) methanogenesis. The utilizations of electron acceptors in the biologically mediated oxidation of organic matter were represented by Monod-type expression. The mass balance equations formulated for the reactive transport of organic matter, electron acceptors, and their corresponding reduced species in the sediments were solved utilizing an iterative multistep numerical method. The ability of model to simulate a freshwater sediments system was tested by comparing simulation results against published data obtained from lake sediments. The simulation results reasonably agreed with field measurements for most species, except for ammonia. This result showed that the C/N ratio (106/16) in the sediments is lower than what the Redfield formula prescribes. Since accurate estimates of vertical profiles of electron acceptors and their reduced species are important to determine the mobility and bioavailability of trace metals in the sediments, the model has potential application to assess the stability of selected trace metals in the sediments.

• Korean Chemical Engineering Research
• /
• v.57 no.5
• /
• pp.743-748
• /
• 2019

This study focuses on the simulation of wet flue gas desulfurization process for improving the production of gypsum by the utilization of low-grade limestone. At present, high-grade limestone with a $CaCO_3$ content of 94% is used for producing merchantable gypsum. In modeling process, a lot of reactions are considered to develop model. First, the limestone dissolution is simulated by RSTOIC model. Second, SOx absorption and crystallization is used by RCSTR model. Finally the gypsum is separated by using SEPERATORS model. Modeling steps make it easy to reflect further side reactions and physical disturbances. In optimization condition, constraints are set to 93% purity of gypsum, 94% desulfurization efficiency, and total use of limestone at 3710 kg/hr. Under these constraints, the mass flow of low-grade limestone was maximized. As a result, the maximum blending quantity of low-grade limestone for 2,100 kg of high-grade limestone that satisfies constraints is about 1,610 kg.