• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.6 no.1
• /
• pp.24-28
• /
• 2005

A micromachined biochip with a three dimensional silicon chamber was developed for the construction of biosensors. Anisotropic etching was used fur the formation of the chamber on the p-type silicon wafer(100) and then was glued to the Pyrex glass bottom-substrate with pre-deposited platinum electrode. The electrochemical characterization of its Pt electrode and Ag/AgCl reference electrode was investigated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.4
• /
• pp.263-268
• /
• 2001

This paper describes the effects of applied bias conditions on electrochemical etch-stop characteristics. THere are a number of key issues such as diode leakage and ohmic losses which arise when applying the conventional 3-electrochemical etch-stop to fabricated some of he MEMS(microelectro mechanical system) and SOI(Si-on-insulator) structures which employ SDB(Si-wafer direct bonding). This work allows to perform anin situ diagnostic to predict whether or not an electrochemical etch-stop would fail due to diode-leakage-induced premature passivation. In addition, it presents technology which takes into account the effects of ohmic losses and allows to calculate the appropriate bias necessary to obtain a successful electrochemical etch-stop.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.423-426
• /
• 1998

Piezoresistive pressure sensors have fabricated using electrochemical etch-stop technique. Si diaphragm having thickness of n-epi. layer was fabricated and used to detect pressure range from 0 to 1 kg/$\textrm{cm}^2$. Piezoresistors were diffused 3${\times}$10$\^$18/ cm$\^$-3/ and placed at diaphragm edge for maximum pressure detection. The characteristics of electrochemical etch-stop in TMAH/lPA/pyrazine solution were also discussed. I-V curves of n and p-type Si in TMAH/lPA/pyrazine solution were obtained. Etching rate is highest at optimum etching condition, TMAH 25wt.%/IPA 17vo1.%/pyrazine 0.1/100m1, thus the elapsed time of etch-stop was reduced.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.397-400
• /
• 1997

This paper presentes the characteristics of Si anisotropic etching and electrochemical etch-stop in aqueous TMAH/IPA/pyrazine solution. (100) Si etching rate of 0.747 $\mu\textrm{m}$/min which faster 86% than TMAH 25 wt.%/IPA 17 vol.% solution was obtained using best etching condition at TMAH 25 wt.%/IPA 17 vol.%/pyrazine 0.1 g and the etching rate of (100) Si was decreased with more additive quantity of pyrazine. I-V curve of p-type Si in TMAH/IPA/pyrazine was obtained. OCP(Open Circuit Potential) and PP(Passivation Potential) were -2 V and -0.9 V, respectively. Si diaphragms were obtained by electrochemical etch-stop in aqueous TMAH/IPA/pyrazine solution.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.362-365
• /
• 1999

This paper describes on thinning SDB SOI substrates by SDB technology and electrochemical etch-stop. The surface of the fabricated SDB SOI substrates is more uniform than that grinding or polishing by mechanical method, and this process is possible to accurate SOI thickness control. During Electrochemical etch-stop, leakage current versus voltage curves were measured for analysis of the open current potential (OCP) point and the passivation potential (PP) poin and determinated to anodic substrates were analyzed by using AFM and SEM, respectivelv.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.73-73
• /
• 2011

Zn-Sn-O (ZTO) 다성분계 산화물 박막은 일반적인 rf 스퍼터법으로 성막할 경우 비정질상으로 성장하여 결정질 산화물 박막에 비해 우수한 표면평탄도와 식각 단면을 제공한다. 비정질임에도 불구하고 넓은 자유전하 농도 범위에서 높은 Hall 이동도를 제공할 수 있는 것으로 보고되어 있어 비정질 산화물의 투명도전성 박막에 대한 관심이 높아지고 있다. 투명 TFT에 적용되는 또 다른 비정질계 산화물 박막인 In-Zn-O (IZO) 박막에 비해 ZTO 박막은 상대적으로 제한된 연구가 이루어졌으나, In의 함유되지 않아 경제적으로 유리하고, 특히 SnO2의 우수한 기계적 및 화학적 특성과 ZnO의 내환원성 특성을 잠재하고 있는 유망한 투명도전성 박막재료이다. 본 연구에서는 Zn-Sn-O계 박막을 통상의 rf 스퍼터법으로 성막하여 조성, 증착 온도, 그리고 열처리 온도에 따른 ZTO 박막의 구조적인 특성 변화와 이에 따른 전기적 및 광학적 특성 변화에 대하여 고찰하였다. ZnO 타겟과 SnO2 타겟을 사용하여 co-sputtering하여 ZnO의 부피 분률을 13~59 mol%까지 변화되도록 조절하여 증착하였다. 증착 온도는 상온, 150 및 $300^{\circ}C$로, 그리고 성막가스 중의 산소분률은 0%, 0.5% 및 1% 로 변화시켰다. 40 mol% 이상의 ZnO를 함유한 ZTO 박막은 가시광 영역에서의 평균 광투과도는 좋으나 전기적인 특성이 열악하였으며, ZnO 분율이 낮은 ZTO 박막은 10-2~10-3 ohm-cm 정도의 비교적 낮은 비저항을 나타내었으나 광투과도 면에서 떨어지는 단점을 보였다. 평균 광투과도는 증착 온도가 증가할수록, 그리고 산소의 양이 증가할수록 향상 되었다. 자유전하농도가 1017~1020 cm-3 정도의 넓은 범위에서 10 cm2/Vs 을 넘는 홀 이동도를 가지는 ZTO 박막의 증착이 가능함을 확인하였으며, 이로부터 투명 TFT 소자로 적용이 가능성이 있음을 보였다. EPMA를 이용한 정량분석 및 XRD를 이용한 구조분석과 연계한 ZTO 박막의 물성 및 최적 조건에 대한 논의가 이루어질 것이다.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.157-161
• /
• 2000

In order to investigate the substrate effect on the electrochemical properties of thin-film electrode, $LiCoO_2$ was deposited onto the alumina, chemically etched-Si and flat-Si substrates. After annealing at $800^{\circ}C$ in $O_2$ for 30min, the film deposited on the alumina consisted of large particles with several cracks, whereas the film deposited on the flat-Si substrate was composed of very small and uniform particles. The films deposited on the flat-Si showed improved electrochemical properties such as peak potential divergence and rate-capability, over those deposited on the alumina and chemically etched-Si substrate, which can be attributed to the differences of the particle size surface morphology, and the electrical resistance of the current collector.

• Analytical Science and Technology
• /
• v.19 no.5
• /
• pp.394-399
• /
• 2006

The polishing performance and the relationships of electrochemistry depending upon oxidizers and additives in the tungsten CMP slurry used in semiconductor industry were investigated. Hydrogen peroxide, ferric nitrate and potassium iodate were used as oxidizers and they showed different oxidation reactions on tungsten film depending on the kind of oxidizers and pH of slurry. The differences influenced the polishing performance. Etching reaction was predominated in the hydrogen peroxide. However, passivation reaction was prevailed in ferric nitrate and potassium iodate. TMAH and KOH raised the potential energy and removal rate of tungsten, and improved a dispersion characteristic of slurry by increasing absolute value of zeta potential. Addition of 100 ppm of poly(acrylic acid) of M.W. 250,000 improved dispersion ability.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.178-181
• /
• 2005

Silicon oxynitride (SiON) layers deposited upon a $SiO_2/Si$ buffer layer placed upon silicon wafers have been obtained by using PECVD from $SiH_4,\;N_2O$, and $N_2$. It can be seen that the refractive index, measured by using a prism coupler, for the SiON films can be varied between 1.4480 and 1.4958 at a wavelength of 1552 nm by changing the process parameters. Optical planar waveguides with a thickness of $6{\mu}m$ and a refractive index contrast ($\Delta$n) of $0.36\% have been deposited. Also, etching experiments were performed using ICP dry etching equipment on thick SiON films grown onto Si substrates covered by a thick $SiO_2$ buffer layer. A polarization maintaining single-mode fiber was used for the input and a microscope objective for the output at $1.55{\mu}m$. As a result, a low index contrast SiON based waveguide is fabricated with easily adjustable refractive index of core layer. It illustrates that the output intensity mode is a waveguiding single-mode.

• Korean Journal of Materials Research
• /
• v.1 no.4
• /
• pp.214-220
• /
• 1991

The effects of $SiO_2$ reactive ion etching (RIE) in $CHF_{3/}C_2F_6$ on the surface properties of the underlying Si substrate were studied by X-ray photoelectron spectroscopy(XPS) and secondary ion mass spectrometry(SIMS) techniques. Angle-resolved XPS analysis was carried out as non-destructive depth profile one for investigating the chemical bonding states of silicion, carbon, oxygen and fluorine. The residue layer consists of C-F polymer. O-F bond was found on the top of the polymer layer and Si-O, Si-C and Si-F bonds were detected between Si substrate and polymer film. A 60nm thick damaged layer of silicon surface mainly contains carbon and fluorine.