• Applied Chemistry for Engineering
• /
• v.30 no.6
• /
• pp.673-680
• /
• 2019

GAP or GAP-co-BO based energetic thermoplastic elastomers (ETPEs) were synthesized by changing the hard segment content percent in the range of 30~45% by 5% difference. Thermal and mechanical properties of GAP-co-BO based ETPEs were compared to those of GAP based ETPEs. FT-IR results showed that the capability of forming hydrogen bond increases with increasing the hard segment content in GAP/GAP-co-BO based ETPE, and also the GAP-co-BO based ETPEs are stronger than GAP based ETPEs in the hydrogen bond formation. DSC and DMA results showed that the glass transition temperature (T_g) of GAP based ETPEs increased with the increment of the hard segment content, while the T_g of GAP-co-BO based ETPEs was maintained even the hard segment content increased. The storage modulus at room temperature of the GAP-co-BO based ETPEs was higher than that of the GAP based ETPEs. This was due to the strong phase separation behavior of the hard and soft segment of GAP-co-BO based ETPEs, which further resulted in the stronger breaking strength and lower tensile elongation at break point for GAP-co-BO based ETPE than the GAP based one.

• Korean Journal of Poultry Science
• /
• v.37 no.2
• /
• pp.151-158
• /
• 2010

TCM-KWG (tissue culture medium waste after harvest of Korean wild ginseng) (panax ginseng) is left over of tissue culture medium used to grow Korean wild ginseng (KWG). The present study was conducted to investigate the effect of TCM-KWG on meat quality and the possible of application as additives in broiler chickens. A day old broiler chickens randomized in 6 groups (n=60/groups) were administered orally with 2, 4, 8, 16, 32 mL/L TCM-KWG through drinking water with one untreated control group. After administration for five weeks, we analyzed chemical composition and meat quality. Crude ash increased approximately 20% in TCM-KWG treatment groups as compared to control group whereas the concentration of moisture, crude protein and crude fat did not show any significant difference. Crude ash is essential to enhance skeleton formation and physiological function. TCM-KWG treatment gradually decreased the pH value of breast meat whereas it did not change the purge loss and cooking loss. The pH value of meat is important for preservation of meat for longer periods and high durability strength. These results suggest that TCM-KWG treatment may improve the quality of meat and can be apply as food additives in chickens.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.122-122
• /
• 2014

수중방전을 환경분야에 적용하기 위한 플라즈마 부상법이 개발되었다. 플라즈마 부상법은 물 속에서 발생시킨 플라즈마가 가지고 있는 주요특성 중 물리적 특징인 쇼크웨이브, UV조사, 버블생성 등과 화학적 특징인 OH라디칼 및 염소산화물 생성 등을 이용하여 물 속에 존재하는 용존성 및 입자성 물질을 부상분리 기법으로 제거하는 공법이다. 유기물을 제거하는 기작으로는 침전, 여과, 분해 등이 있고, 이를 구현하기 위한 공정으로 중력침강법, 부상분리법, 멤브레인법, 미생물법 등이 있다. 이 중에서 가압공기부상법은 침강법에 비해 부지면적을 적게 소모하고 처리시간이 50% 이상 감소되는 특징이 있다. 가압공기부상법은 물 속에 공기를 과포화시킨 후 노즐을 통해 재분사할 때 발생하는 압력차에 의해 미세기포가 발생함을 이용하여 유기물을 분리하는 공법이다. 그러나, 가압용 장비 및 반송수가 필요하고, 미생물분리는 불가능한 단점이 있다. 이에 본 연구에서는 미생물살균과 유기물 분리가 동시에 일어나는 플라즈마를 이용한 부상분리기법을 개발하였다. 본 연구에서는 난분해성 용존유기물인 휴믹산 100 mg/L의 플라즈마 공기부상법에 의한 제거능을 확인하였다. 용존성 휴믹산을 입자성 물질로 전환하여 플록을 형성시키고자 알루미늄설페이트(Al2(SO4) $3{\cdot}18H2O$)를 100 mg/L 주입하였고, 침출수와 같이 염도가 높은 물을 모사하고자 35 g/L의 염화나트륨을 첨가한 상태에서 방전을 실시하였다. 방전에 사용된 전원은 EESYS사에서 제작한 펄스형 고전압 전원장치를 사용하였고 최대 15 kW의 출력 중 6 kW의 전력을 인가하였다. 전극 한 개는 2 mm 텅스텐봉을 세라믹튜브로 감싼 구조로 총 사용전극은 28개이다. 전극 한 개당 대략 200 Watt의 전력이 소모되며 이 때 최대의 버블이 생성됨을 확인하였다. 전극 1개에서 생성되는 버블의 부피는 14 mL/min 로 측정되었다. 버블의 크기는 평균 70 um이고 가압공기부상법에서 최적공기크기로 제시하고 있는 40~80 um 의 버블은 약 80% 가량 생성된다. 본 연구에서 사용된 반응시스템에서의 물의 높이는 약 500 mm 이고 전체 40 L의 수조가 3개의 벽으로 분리되어 4개의 수조로 분리되었다. 각 수조는 하부에 7개의 전극을 포함하고 있다. 플라즈마 발생시 생성되는 기포는 약 1분 방전 후에 포화농도에 도달하며 방전종료 후 약 4분간 수체 내에 남아있게 된다. 이를 공정에 적용하여 1분 방전 및 4분 휴지의 순서로 플라즈마를 인가하였다. 휴믹산 용액의 유량을 2 lpm 으로 운전하였을 때 최종 처리율은 94% 이고 이때의 대장균 살균능은 99%이다.

• Applied Chemistry for Engineering
• /
• v.23 no.5
• /
• pp.433-439
• /
• 2012

In this study, a cationic surfactant BHMAS (N,N-bis-(3'-n-dodecyloxy-2'-hydroxypropyl)-N-methyl-2-hydroxyethylammonium methyl sulfate) having two lauryl and three hydroxyl groups was synthesized by the reaction of n-dodecyl glycidyl ether and 2-aminoethanol followed by the quarternization with dimethyl sulfate. The structure of the product was elucidated by $^{1}H-NMR$ and FT-IR. The CMC (critical micelle concentration) and surface tension of BHMAS at CMC condition were found to be $9.12\;{\times}\;10^{-4}$ mol/L and 28.71 mN/m respectively. Dynamic surface tension measurements using a maximum bubble pressure tensiometer indicated that a relatively long time was required to saturate the interface between air and aqueous surfactant solution. The interfacial tension measured between 1 wt% surfactant solution and n-decane reached an equilibrium value of 0.045 mN/m in 5 min. The adsorption capacity of the synthesized surfactant was observed to be excellent, which suggests that the surfactant can be used as a softening agent during a laundry process.

• Asian Oncology Nursing
• /
• v.4 no.1
• /
• pp.38-48
• /
• 2004

Purpose: The purpose of this study was to identify the effects of foot massage on the degree of nausea/vomiting, anxiety, sleep satisfaction and fatigue during chemotherapy. Method: Total 36 subjects who were admitted to C university hospital in G city during 3 days and 2 nights for chemotherapy were selected from January to June, 2003. Seventeen of these subjects were assigned to control group and the rest were assigned to experimental group. Tools were Index of Nausea, Vomiting & Retching (INVR), Spielberger's state anxiety, sleep satisfaction, & fatigue VAS. Data were collected at both pre-test and post-test. Results: Difference of pre-test and post-test was not significant between control group and experimental group on the degree of nausea/vomiting, anxiety and sleep satisfaction. However, the effect of foot massage on the fatigue was significant. Conclusion: Further studies need to identify the immediate effect of foot massage on either nausea and vomiting or anxiety and to develop strategies for lengthening and strengthening the short-term effect of foot massage.

• Polymer(Korea)
• /
• v.35 no.1
• /
• pp.23-29
• /
• 2011

We measured shear viscosity of polymeric particles, prepared by suspension polymerization with hydrophobic silica as a stabilizer at $75^{\circ}C$, by a capillary rheometer. Shear viscosity displayed a non-Newtonian behavior with an increase in weight average molecular weight. Measurement of shear viscosity at 170 and $190^{\circ}C$ with copoly(styrene/butyl methacrylate) (co-PSB) particles by varying the ratio between styrene (St) and butyl methacrylate (BMA) showed that shear viscosity was a function of molecular weight, temperature and compositional ratio. When the ratio was 7/3, 5/5 and 3/7, shear viscosity slightly reduced with an increase in BMA concentration despite similar weight average molecular weights. We found that shear viscosity of copolymers with BMA concentrations exceeding 70% displayed a sharp reduction at high shear rates. It is speculated that increased PBMA chain length contributes to enhanced flowability of copolymers. When carbon black was incorporated into co-PSB, shear viscosity progressively increased with increasing carbon black concentration. The increase in shear viscosity, however, was less pronounced compared to the cases of molecular weight increase.

• Korean Chemical Engineering Research
• /
• v.51 no.4
• /
• pp.476-481
• /
• 2013

Ethylbenzene (EB) which has a similar physical properties with p-xylene (pX) was separated from EB/pX mixture by using MFI-type zeolite (TS-1, ZSM-5, and Silicalite-1) coated membranes. The zeolites were synthesized by microwave method to reduce the synthesis time and uniformly formed zeolite particles were coated on the ${\alpha}$-almina tubular support with a thickness of $3-4{\mu}m$. Separation factor and permeation flux of the synthesized zeolite coated membranes were measured to survey the best performance of ethylbenzene separation from different composition of EB/pX mixtures. When the EB/pX mixture of 5:5 molar ratio applied for the separation experiment, it represented the highest separation factor. We also have studied about the effect of the atomic composition of zeolites on the separation performance within the temperature range from 160 to $220^{\circ}C$. TS-1 showed the highest permeation flux of $1,666mol/m^{2*}s^*Pa$ and Silicate-1 showed the highest separation factor of 1.73 at $200^{\circ}C$ respectively.

• The Journal of the Acoustical Society of Korea
• /
• v.35 no.6
• /
• pp.473-479
• /
• 2016

We report a highly selective and sensitive 200 MHz Surface Acoustic Wave (SAW) sensor that can detect cyanide ion in aqueous solution using surface immobilized thioester molecules in combination with gold nanoparticles (AuNPs). To construct the sensor device, a monolayer of thioester compound was immobilized on the SAW sensor surface. At the sensor surface, hydrolysis of thioester group by nucleophilic addition of cyanide occurred and the resulting free thiol unit bound to AuNP to form thiol-AuNP conjugate. For the signal enhancement, gold staining signal amplification process was introduced subsequently with gold (III) chloride trihydrate and reducing agent, hydroxylamine hydrochloride. The SAW sensor showed a detection ability of $17.7{\mu}M$ for cyanide in aqueous solution and demonstrated a saturation behavior between the frequency shift and the concentration of cyanide ion. On the other hand, our SAW sensor had no activities for other anions such as fluoride ion, acetate ion and sulfate ion, moreover, no significant interference observed by other anions. Finally, all the experiments were carried out in-house developed sensor and fluidics modules to obtain highly reproducible results.

• Journal of Periodontal and Implant Science
• /
• v.35 no.3
• /
• pp.525-536
• /
• 2005

여러 연구들을 통해 많은 학자들이 임프란트 안정성(stability)은 표면의 특징에 달려있다고 생각하게 되었다. 표면의 구조, 에너지, 산화물(oxide) 두께와 표면성상(topography)등 임프란트의 표면의 특징은 임프란트와 골조직의 반응에서 중요한 역할을 하는 것이 알려짐에 따라 티타뮨 임프란트의 표면의 처리 방법에 큰 관심을 가지게 되었다. 그 중에서 티타늄 임프란트 표면의 산화피막화(anodization)가 한 방법으로 대두되었다. 이 방법은 전기화학적 방식으로 임프란트 표면에 거칠고(rough)두꺼우며(thick), 기공(pore)을 가지는 산화물 막을 형성하는 것으로 산화물의 두께는 coronal 부분(l-2 ${\mu}m$)으로부터 apical부분(7-10 ${\mu}m$)까지 증가하게 된다. 산화피막의 표면에는 다양한 크기의 수많은 기공이 주로 1-2 ${\mu}m$ 두께로 임프란트의 apical 부분에서 존재하며, 임프란트 표면의 거칠기는 conical 위부분에서 apical 부분까지 계속 증가한다(평균 Ra value=1.2 ${\mu}m$). 또 다른 표면 처리 방법으로는 blasting 후에 etching을 한 SLA 표면이 있다. 이 연구의 목적은 일반적으로 많이 이용되고 있는 anodized 표면과 SLA 표면의 조직학적 반응을 비교 분석하는 것이다. 24개 임프란트를(anodized surfaced implant-12개 , SLA-12개, 8mm ${\times}\;{\Phi}$ 4.3) 6마리 토끼의 오른쪽과 왼쪽 femur에 식립하였다. 12주후에 동물들을 희생하여 EXACT cutting-grinding system을 이용하여 샘플을 절단하고 800, 1200 및 4000 번 연마제(abrasive) paper로 20-50 ${\mu}m$ 까지 grinding하였다. 샘플은 Multiple staining 용액으로 염색하여 SLA 임프란트 군과 비교하였다. 골과 임프란트 사이에 연결을 TDI 프로그램을 이용하여 %로 측정하였다. SLA 임프란트 군 경우에는 골과 임프란트 사이의 연결이 $74{\pm}19%$ 이고, 양극 산화한 임프란트 군 경우에는 $77{\pm}9%$이었다. 양극 산화한 티타늄 임프란트의 골 접촉률이 SLA 표면 임프란트 경우과 통계학적으로 유의한 차이는 보이지 않았다.

• Korean Chemical Engineering Research
• /
• v.57 no.4
• /
• pp.584-588
• /
• 2019

The catalytic combustion of particulate matter (PM) is one of the key technologies to meet emission standards of diesel engine system. Therefore, we herein suggest Ag loaded $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst. They were produced by the electrospinning method. FE-SEM, EDS mapping, XRD, XPS were studied to investigate the crystal and morphological structures of loaded Ag particles and $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst. Following the catalytic soot oxidation, we found that the Ag loaded $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskiteweb catalyst showed the higher catalytic activities (e.g., $T_{50}=490^{\circ}C$) than the only $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst (e.g., $T_{50}=586^{\circ}C$). Thus, this finding suggests that Ag loaded $La_{0.6}Sr_{0.4}Co_{0.2}Fe_{0.8}O_3$ perovskite web catalyst can be a promising candidate for enhancing the soot oxidation.