• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.6
• /
• pp.185-190
• /
• 2023

Recently, tracking radar requires the development of millimeter wave tracking radar to acquire target information with high resolution in various environments. The development of millimeter wave tracking radar requires the development of transmission and receiving components that can be applied to the millimeter wave tracking radar, as well as verification of the applicability of the tracking radar. In order to verify the applicability of the developed transmitting and receiving components, it is necessary to develop a signal acquisition device that can control the transmitting and receiving components using the operating concept of a tracking radar and check the status of the received signal. In this paper, we implemented a signal acquisition device that can confirm the applicability of components developed for millimeter wave tracking radar. The signal acquisition device was designed to process in real time the OOOMHz center frequency and OOMHz bandwidth signals input from 4 channels to verify the received signal. In addition, component control applying the tracking radar operation concept was designed to be controlled by communication such as RS422, RS232, and SPI and generation of control signals for the transmission and receiving time. Lastly, the implemented signal acquisition device was verified through a signal acquisition device performance test.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.1
• /
• pp.69-78
• /
• 2008

Shearing strength test in tension type was investigated to determine the shear resistance of bolt and drift-pin connection of domestic larix glulam. The specimen was connected with bolt and drift-pin in the inserted plate type, and only bolt in the side plate type. The diameter of bolt and drift-pin used in the experiment are 12, 16 and 20 mm. The hole of bolt was drilled at the end-distance 5 d and 7 d. Tension load was loaded in the direction parallel to grain. The shear resistance was evaluated according to end-distance through this, the yield load was compared with the experimental yield load, using Larsen's formula. The prototype design strength is based on the yield load of end-distance 7 d and the reduction factor of end-distance 5 d was calculated. The results were as follows. 1. The average of maximum load of drift-pin connection was higher by 3~30% at the inserted type than at bolt connection with increasing diameter. In bolt connection, the average of maximum load of the side type was 1.54~2.07 times higher than that of the inserted type. In the same diameter, the average of maximum load of end-distance 7 d was higher by 8~44% than that of 5 d. 2. The bearing stress was 1.16~1.41 times higher at the inserted connection than at drift-pin connection, and 1.37~1.86 times higher at 7 d than at 5 d. Also, when the slenderness ratio was below 7.5 at drift-pin connection and below 6.0 at inserted connection, the lateral capacity was good. 3. The ratio of the experimental yield load and the predicted yield load calculated by Larsen's formula proposed by Larsen was 0.80~1.10 at inserted connection, and 0.75~1.46 at side connection. 4. When the inserted bolt connection was based on the yield load of end-distance 7 d, the reduction factor was 0.89 at 12 mm connection, 0.93 at 16 mm and 0.85 at 20 mm. The reduction factor was 0.89 at 12 mm the inserted drift-pin connection, 0.93 at 16 mm, 0.93 at 20 mm. The reduction factor was 0.79 at the side connection of the 12 mm bolt connection and 0.80 at 16 mm.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.4
• /
• pp.318-325
• /
• 2011

Pitch pine (Pinus rigida Miller) retaining walls using Steel bar, of which the constructability and strength performance are good at the construction site, were manufactured and their strength properties were evaluated. The wooden retaining wall using Steel bar was piled into four stories stretcher and three stories header, which is 770 mm high, 2,890 mm length and 782 mm width. Retaining wall was made by inserting stretchers into Steel bar after making 18 mm diameter of holes at top and bottom stretcher, and then stacking other stretchers and headers which have a slit of 66 mm depth and 18 mm width. The strength properties of retaining walls were investigated by horizontal loading test, and the deformation of structure by image processing (AlCON 3D OPA-PRO system). Joint (Type-A) made with a single long stretcher and two headers, and joint (Type-B) made with two short stretchers connected with half lap joint and two headers were in the retaining wall using Steel bar. The compressive shear strength of joint was tested. Three replicates were used in each test. In horizontal loading test the strength was 1.6 times stronger in wooden retaining wall using Steel bar than in wooden retaining wall using square timber. The timber and joints were not fractured in the test. When testing compressive shear strength, the maximum load of type-A and Type-B was 130.13 kN and 130.6 kN, respectively. Constructability and strength were better in the wooden retaining wall using Steel bar than in wooden retaining wall using square timber.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.6
• /
• pp.77-87
• /
• 2008

Wooden model erosion control dam was made with pitch pine, of which the strength properties was evaluated. Wooden model erosion control dam was made with diameter 90 mm of pitch pine round posts treated with CUAZ-2 (Copper Azole), changing joint in three different types. In each type, erosion control dam was made in nine floor (cross-bar of five floors and vertical-bar of four floors), of which the hight was 790 mm. And then strength properties were investigated through horizontal loading test and impact strength test, and the deformation of structure through image processing (AICON 3D DPA-PRO system). In horizontal loading test of wooden model erosion control dam using round post of diameter 90 mm, whether there was stone or not did not affect strength much when using self drill screw, but strength was decreased by 23%. In monolithic type of erosion control dam using screw bar, strength was increased by 1.5 times and deformation was decreased when filling with stone. When reinforcing with screw bar that ring is connected to self drill screw, strength was increased by 4.8 times. In impact strength test of wooden model erosion control dam made with round post of diameter 90 mm, the erosion control dam connected with self drilling screw not filling with stone was totally destroyed by the 1st impact, and the erosion control dam using screw bar was ruptured at cross-bar at which 779 kgf of impact was loaded in the 1st impact. In the 2nd impact, the base parts were ruptured, and reaction force was decreased to 545 kgf. In the 3rd impact, whole base parts were destroyed, and reaction force was decreased to 263 kgf.

• Progress in Medical Physics
• /
• v.12 no.1
• /
• pp.51-58
• /
• 2001

Synchrotron radiation (SR) has several advantages over convetional x-rays, including its phase, collimation, and high flux. A synchrotron radiation beamline 5C1 at Pohang Light Source (PLS) was recently built for imaging applications. We have shown that a SR imaging system is useful in imaging microscopic structures. SR with broad-band energy spectrum were adjusted to an object by Si wafers and their energy were approximately ranging from 6 keV to 30 keV. SR were passed through an object and finally transformed into visible lights by CdWO$_4$ scintillator screen. The visible lights which were reflected at an angle of 90 degrees by gold plated mirror were detected by a CCD camera and the image data were acquired using image acquisition system. A high-resolution phantom, capacitor, adult tooth, child tooth, cancerous breast tissue, and mouse lumbar vertebra were imaged with SR imaging system. The Objects were rotated within the field of view of the CCD detector, and their projection image data were obtained at 250 steps over 180 degrees rotation. Image reconstructions were carried out in a PC by using IDLTM(Research systems, Inc., US) program. The spatial resolution of the images acquired by the SR imaging system was measured with a high-resolution chart manufactured for several micrometer resolution. The specimens were also imaged with conventional x-ray radiography system to compare the image quality of radiography obtained with the SR imaging system. The results showed more structural details and high contrast images with SR imaging system than conventional x-ray radiography system. The SR imaging system may have a potential for imaging in biological researches, material applications, and clinical radiography.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.1
• /
• pp.52-60
• /
• 2006

This study investigated how wood properties (i.e., annual rings, sapwood, heartwood, and cracks) might affect preservative treatment in Japanese larch (Larix leptolepis) round-wood product. We specially focused on small-diameter (~10 cm diameter) wood that is commercially sold in market. Among 100 wood samples, the groups of sample with 13~16, 17~20 annual rings represented 33 and 27 in each frequency, while 2~3 and 4~5 mm annual ring width accounted for 72 and 68 in frequency. More than a half (54%) of wood samples contained a mix of heartwood and sapwood in its surface. The rest (46%) had only heartwood exposed in the wood surface. A wide range of checks were showed in the wood samples, but the highest frequency was observed in samples with 1~6 surface (1~14 mm in size) checks and 1~4 end-grain (8~14 mm in size) checks in each round-wood sample. Pressure treatment resulted in a wide range of penetration of ACQ (Alkaline Copper Quat) into the wood, showing $4.3{\pm}4.19mm$ penetration in the wood samples contained a mix of heartwood and sapwood in its surface. However preservative treatment was much less effective for the heartwood only wood samples, ranging average 1.3 mm with ACQ and 1.1 mm with CCA (Chromated Copper Arsenate). These penetration results shown in heartwood samples did not meet the penetration standard that is required for H3 by the Korean Forest Service in relation to wood preservation treatment. These low penetration results were not significantly improved even if we incised wood samples to improve treatment effect, showing only small increase of 0.7 mm with ACQ and 0.6 mm with CCA. When preservative treatment was tested with heartwood, penetration of preservatives decrease with increase of annual rings per a cross-section area (r=0.5345). We also found that the length and number of check had no effect on preservative treatment, showing r=0.1301 and r=0.1802, respectively.

• Journal of Forest and Environmental Science
• /
• v.8 no.1
• /
• pp.21-33
• /
• 1992

This study was performed to investigate the hardness of wood related to the wood surface, sap and heartwood, early and latewood, specific gravity, annual ring width and moisture content on major Korean tree species such as Pinus koraiensis, Abies holophylla, Larix leptolepis and Quercus valiabilis. The results were summarized as follows: 1. The arithmetic mean values of wood hardness on cross section were respectively $8.0kg/mm^2$ on Quercus valiabilis, $7.4kg/mm^2$ on Larix leptolepis, $5.1kg/mm^2$ on Pinus koraiensis and $4.7kg/mm^2$ on Abies hollophylla. 2. Generally hardness of wood on cross section was greater than the others and the proportion of cross section hardness to radial was respectively 2.8 on Quercus valiabilis, 2.6 on Larix leptolepis, 3.8 on Pinus koraiensis, and 4.1 on Abies holophylla and that proportion was tend to be decrease as specific gravity increased. 3. It was recognized that the hardness of sap and heartwood was different from each of the tree species and generally heartwood hardness was somewhat greater than sapwood. 4. Generally latewood hardness with in a ring was greater than earlywood and the proportion of earlywood hardness to latewood decreased as specific gravity increased. 5. The relations between hardness of wood and specific gravity show a high positive correlation on all sample tree species. 6. The values of hardness decreased with increasing annual ring width. 7. Hardness of wood on Abies holophylla was greatest in oven dried wood and it was decreased as moisture content increased, but not changed with moisture content abve F.S.P.. The proportion of oven dried wood hardness to green are respectively 3.0 on cross, 2.4 on radial and 1.9 on tangential section.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.1-8
• /
• 2008

The lateral strength test of bending type was done to investigate the lateral capacity of the double bolt connection of domestic larix glulam according to bolt spacing. In the shear specimen, which is bolted connection in the inserted plate type, the hole of bolt was made, changing the diameter of bolt (12 mm and 16 mm), the number of bolt (single bolt : control and double bolt), the direction of bolt row (in parallel to grain : Type-A and in perpendicular to grain : Type-B) and the bolt spacing (Type-A : 4 d and 7 d and Type-B : 3 d and 5 d). Lateral capacity and failure mode of bolt connection were compared according to conditions. In prototype design (KBCS, 2000), the reduction factor of the allowable shear resistance that the bolt spacing is reduced was calculated. The results were as follows. 1) Bearing stress per bolt in the single and double bolt connection of Type-A was directly proportional to bolt diameter and bolt spacing. Bearing stress of Type-B decreased as bolt diameter was increased, and decreased by 2~10% when bolt diameter was increased. 2) In the single bolt connection and the double bolt connection of Type-A, the splitted failure was formed in the edge direction. When the bolt spacing was 3 d in Type-B, bolt was yielded more in the part of tension than in the part of compression, and the splitted failure started at the bolt in the part of tension. In the 5 d spacing specimen, the bolt in the part of tension was yielded similarly to bolt in the part of compression, and the splitted failure started in the part of compression. 3) In the prototype design, the reduction factor was calculated by non-dimensionizing the yielding load in the standard of bolt spacing (Type A : 7 d and Type B : 5 d). In 12 mm bolt connection, the reduction factor of bolt spacing 4 d (type-A) and single bolt connection was 0.87 and 0.55, respectively, and the reduction factor of bolt spacing 3 d (Type-B) and single bolt connection was 0.91 and 0.55, respectively. In 16 mm bolt connection, the reduction factor of bolt spacing 4 d (type-A) and single bolt connection was 0.96 and 0.76, respectively, and the reduction factor of bolt spacing 3 d (Type-B) and single bolt connection was 0.91 and 0.77, respectively.

• Journal of Veterinary Clinics
• /
• v.10 no.1
• /
• pp.65-94
• /
• 1993

This study examined metabolic profiles of 1349 Holstein cows from 91 commercial herds. Thirteen parameters which are consisted of twelve blood components and body condition score were examined and their mean values. standard deviations and standard limits, which are 80% confidential limits, in each lactational stage were reported. The variations of each parameter affected by season, individual milk yield, adjusted corrected milk yield of herd. and lactation number were also reported. A model of metabolic profile test applicable to this country where the average number of cows in a herd is small as to be fifteen is designed. Metabolic profiles as reflected in each parameter were discussed in relation to adequacy of dietary intake for production, milk production, reproductive performance, and diseases, and the possible measure to improve productivity of dairy cows were proposed. Much of the variation in parameters was due to differences between herds, and less to differences between seasons, differences between individual milk yield, and differences between lactational stages. As the average herd size in this country is small, it is believed that all the cows in a herd must be sampled, and the individual result of each parameter was compared with the standard limit for each lactational stage, and the percentage of cows which are outside the standard limits in a herd was calculated to use as a criteria for evaluation of the herd. Data outside the 99% confidential limits were to be deleted at first, but when the trends of the data outside the 99% confidential limits are same as the trends of the data within 99% confidential limits, the deleted data must be reviewed again, otherwise some important informations would be missed. The mean concentration of blood urea nitrogen in this study was much higher than that was reported in England, U.S.A. and Japan, and it was similar to the upper limits reported in England, U.S.A. and Japan. So it was thought that the concentration of blood urea nitrogen is improper as a criteria for protein intake. The increase of serum total protein cocentration beyond standard limits was due to increase of serum globulin concentration in most of the cows. The correlation coefficient between serum and protein and serum globulin concentration was 0.83. Serum globulin concentration was negatively related to adjusted corrected milk of herd. Serum albumin, calcium and magnessium concentrations were negatively related to adjusted corrected milk of herd, which indicate that high-producing individual or high-producing herd have not taken sufficient protein/amino acids, calcium and magnessium. Packed cell volume was negatively related to adjusted corrected milk of the herd, and the trend was same In each lactational stage. The correlation coefficient between serum and packed cell volume was 0.16 and the correlation was very weak. Blood glucose concentration was lowest in early lactational stage, which indicates negative energy balance in early lactational stage. Blood glucose concentration was negatively related to adjusted corrected milk of herd from peak to late lactational stage, which indicates negative energy balance during the period in high-producing individuals or high-producing herds. Correlation coefficient between serum aspartate aminotransferase activity and serum ${\gamma}$-glutamyltransferase activity was 0.41, and this indicates that serum ${\gamma}$-glutamyltransferase should be included as a parameter of metabolic profile test to evaluate liver function. Body condition score of dairy cows in this country was lower than that of Japan in every lactational stages, and the magnitude of increase in body condition score during middle and late lactational stages was small. Metabolic profile can not be evaluated with solely nutritional intake. When an individual or large percentage of cows in a herd have adnormal values In parameters of metabolic profile test, veterinary clinician and nutritionist should cooperate so as to diagnose diseases and to calculate the e of no운ents simultaneously.

• Korean Journal of Heritage: History & Science
• /
• v.54 no.4
• /
• pp.90-111
• /
• 2021

Seojangdaeyajodo is a drawing of Jangyongyoung's military night training on February 12 (lunar leap month), 1795. Focusing on the Seojangdaeyajodo, the positions and roles of the low-ranking soldier belonging to Jangyongyoung, and the composition and characteristics of military uniforms for each role were examined. The results ascertained by the historical research on the military uniforms are as follows. Deungronggun, noeja, sunryeongsu and daegisu who were placed in front of the king's Seojangdae were the low-ranking soldiers belonging to Jangyongyoung. The soldiers who escorted the king around Seojangdae were lowranking soldiers belonging to Jangyongyoung. The military uniform of the deungronggun was consisted of a jeolrip, a black heopsu, red gweja, indigo jeondae, white haengjeon and black shoes. The low-ranking soldier's heopsu suggested that it could also be a sochangui. He carried a sword and a red lantern. Noeja were divided into a sinjeonsu and a jujangsu. The military uniform of the noeja was consisted of a Jujeolrip, a black heopsu, red gweja, indigo jeondae, white haengjeon, and black shoes. Sunryeongsu were divided into a sinsigisu and a younggisu. The military uniform of the sunryeongsu was consisted of a jeongeon, a black heopsu, red gweja, indigo jeondae white haengjeon and black shoes. He carried a sword and a red lantern. The military uniform of the daegisu was consisted of a jeongeon, a black heopsu, blue gweja, indigo jeondae, white haengjeon and black shoes. He carried a sword and a flag. The soldiers surrounding Seojangdae and the seongjeonggun defending the fortress were the Chogun. The military uniform of the chogun was consisted of a jeolrip, a black heopsu, houi, indigo jeondae, white haengjeon and straw shoes. Houi was applying the five directional colors: the east is blue, the west is white, the south is red, and the north is black. He carried a sword and a gun. It was presented as an illustration of costumes that could produce contents by reflecting on these historical results. The basic principle of the illustration was to present the standards for 3D content production or actual production. Samples of form, color, and material according to the times and status were presented. The front, the side, and the back of each costume and the feature were presented, and the colors were presented in RGB and CMYK.