• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.2
• /
• pp.181-186
• /
• 2022

Dam slope RIM is a highly important contact interface where the main body and the base surface are connected. In general, when the grouting for the slope of the dam structure is designed, it is planned using limited data (drilling, geological map, etc.). This makes it very difficult to accurately consider the original ground characteristics of the slope RIM grouting target, In addition, when the grouting volume planned during the design is drilled and injected into the original ground where the waterstop is secured, there is a possibility that the original ground with the waterstop is disturbed and the effect of the waterstop is rather diminished. In order to overcome such problems, it is more suitable to first consider geological conditions and determine whether to perform optimal grouting on the original ground through on-site repair tests before performing RIM grouting. In this paper, to determine the grouting of the RIM unit, a pilot hole water pressure test was performed on the rock of the slope in the target section. The analysis shows grouting volume of 1 Lugeon or less, and the cement injection amount also shows the injection result of 1 kg/m or less. In this case, performing grouting is rather counterproductive. This result can be evaluated through a rock of which some degree of order of mass is secured, as it is a dam design standard of 1 Lugeon or less when analyzed, using the results of visual observation and geological map creation during slope cutting. Therefore, in conclusion, it is preferable to make the decision for using RIM grouting on the slope of the dam body structure, based on 1 Lugeon in a rock state, and the cement injection amount also at 1 kg/m.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.29 no.4
• /
• pp.363-371
• /
• 2023

To construct a ship, blocks of various sizes must be moved and erected . In this process, lugs are used such that they match the block fastening method and various functions suitable for the characteristics of each shipyard facility. The sizes and shapes of the lugs vary depending on the weight and shape of the block structures. The structure is reinforced by welding the doubling pads to compensate for insufficient rigidity around the holes where the shackle is fastened. As for the method of designing lugs according to lifting loading conditions, a simple calculation based on the beam theory and structural analysis using numerical modeling are performed. In the case of the analytical method, a standardized evaluation method must be established because results may differ depending on the type of element and modeling method. The application of this ambiguous methodology may cause serious safety problems during the process of moving and turning-over blocks. In this study , the effects of various parameters are compared and analyzed through numerical structural analysis to determine the modeling conditions and evaluation method that can evaluate the actual structural response of the lug. The modeling technique that represents the plate part and weld bead around the lug hole provides the most realistic behavior results. The modeling results with the same conditions as those of the actual lug where only the weld bead is connected to the main body of the lug, showed a lower ulimated strength compared with the results obtained by applying the MPC load. The two-dimensional shell element is applied to reduce the modeling and analysis time, and a safety working load was verified to be predicted by reducing the thickness of the doubling pad by 85%. The results of the effects of various parameters reviewed in the study are expected to be used as good reference data for the lug design and safe working load prediction.

• Korean journal of applied entomology
• /
• v.44 no.1 s.138
• /
• pp.21-30
• /
• 2005

Feeding behavior of foraging ants including visiting numbers, species, and preference on insect cadavers killed by entomopathogenic nematodes <(Heterorhabditis sp. KCTC 0991BP (He) and Steinernema carpocapsae KCTC 0981BP (Sc)> and their symbiotic bacteria was investigated in Dongrae Benest Golf Club, Anyang Benest Golf Club, Gapyung Benest Golf Club and Ulsan Golf Club. The number of ants, kinds and numbers of cadavers taken away by ants were different depending on killing method, golf club and site within the golf courses (fairway and rough). The feeding preference of ants was the lowest on cadavers killed by He. At Dongrae Benest Golf Club Lasius japonicu ($75{\pm}5\%$) and Monomorium floricola ($10\%$) took away cadavers only at the rough. The visiting rate of ants was $85{\pm}6\%$ at the rough, but none at the fairway by 16 hours. The taken rate of cadavers by ants was the lowest on He-killed cadavers representing $16.7\%$ compared with $40.0\%$ on Sc-killed cadavers, $53.3\%$ on fenitrithion-killed cadavers, and $56.7\%$ on natural dead cadavers by 12 hours. At the rough of hole 6 in Anyang Benest Golf Club, Tetramorium tsushimae ($33{\pm}12\%$), Pheidole fervida ($17{\pm}15\%$), Camponatus japonicus ($10\%$), Formica japonica ($7{\pm}6\%$), Paratrechina flavipes ($3{\pm}6\%$), and Crematogaster matsumurai ($3{\pm}6\%$) took away cadavers, but $23{\pm}15\%$ of cadavers were not visited by ants. Ants took away $40\%$ of Sc-killed cadavers, $16.7\%$ of frozen-killed cadavers, and $3.4\%$ of He-killed cadavers. The number of visiting ants was low at the hole 9 of Cherry course in Gapyung Benest Golf Club and only Tetramorium tsuhimae and Paratrechina flavipes were found from one site. The density of entomopathogenic nematodes did not influence ant visiting on cadavers, but burying affected ant visiting. Although ants took away unburied cadavers, buried cadavers were taken away at the hole 6 of Dongrae Benest Golf Club by 16 hours. Ant visiting had the same tendency on symbiotic bacterium-treated biscuit as nematode-killed cadavers. The visiting was less on biscuit inoculated by Photorhabdus sp., a symbiotic bacterium of He than on biscuit inoculated by Xenorhabdus nematophila, a symbiotic bacterium of Sc.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.2
• /
• pp.203-211
• /
• 2012

The main object of this experiment is to estimate the hydrodynamic forces acting on a submerged streamlined body placed in a one-end-opened cylindrical tube moving with certain translational velocity. The best experimental design for this object is mimicking real situation, however sizes of model body and cylinder tube are just the same as those of real, for avoiding scale effects, mimicking real situation is not realizable. Hence, in this experiment, target body and cylindrical tube were designed to be towed with varying body position relative to cylindrical tube. For measuring hydrodynamic forces and flow velocity in the cylindrical tube, six one-component load cells and several one-hole Pitot tubes were used. Several conditions were checked with various end-plates those had different opening areas. Experiment results show that forces and flow velocity had different tendency with those expected, and the presence of a end-plate slows down the flow velocity in the cylindrical tube and affects pressure field in the tube to push the model submerged body forward of the tube. This tendency grows with decreasing opened area.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.412-412
• /
• 2016

염료감응 태양전지(dye-sensitized solar cells, DSSCs)는 식물의 광합성원리와 매우 유사한 작동원리를 갖고 있는 전지이며, 간단한 구조, 저렴한 제조단가, 친환경성 등의 등의 장점으로 인하여 많은 관심을 모으고 있다. 이러한 염료감응 태양전지는 빛을 받아들인 염료분자가 전자-홀 쌍을 생성하며 전자는 반도체 산화물을 통해 이동되고 전해질의 산화환원 과정을 통해 염료 분자가 다시 환원되는 순환메커니즘을 따르고 있다. 일반적으로 염료감응 태양전지는 밴드 갭 에너지가 큰 반도체 산화물을 포함하는 작업전극, 산화환원 반응을 통해 전자를 염료로 보내는 전해질, 환원 촉매역할을 하는 상대전극으로 구성되어 있다. 특히, 상대전극으로는 우수한 촉매특성과 높은 전도성을 갖는 백금이 가장 많이 이용되고 있지만 가격이 비싸고 요오드에 취약하기 때문에 상용화에 큰 장애물이다. 따라서, 백금을 대체하기 위해 저가의 탄소나 고분자에 대한 연구가 활발히 진행되고 있고, 그 중 탄소나노섬유(carbon nanofiber, CNFs)는 높은 표면적과 뛰어난 화학적 안정성으로 촉매효율을 증대시킬 수 있어 촉매물질로서 관심이 높아지고 있다. 본 연구에서는 상대전극에 탄소나노섬유기반 복합체를 합성하였고, 성공적으로 저가격 및 고성능의 염료감응 태양전지를 제작하였다. 이때, 지지체인 탄소나노섬유는 전기방사법을 통해 합성하였으며, 수열합성법을 이용하여 금속산화물을 담지하였다. 이렇게 제작된 탄소나노섬유-Fe2O3 복합체는 scanning electron microscopy, transmission electron microscopy, X-ray diffraction, 그리고 X-ray photoelectron spectroscopy 통해 구조적, 화학적 특성을 평가하였으며 전기화학적 특성 및 광전변환 효율을 분석하기 위해 cyclic voltammetry, electrochemical impedance spectroscopy, 그리고 solar simulator를 사용하였다. 본 학회에서 위와 관련된 더 자세한 사항에 대해 논의할 것이다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.449-449
• /
• 2013

최근 반도체 소자의 집적회로는 점점 복잡해지고 있는 반면, 소자의 크기는 작아지고 있으며 그로 인해 패드의 크기가 작아지고 패드사이의 간격 또한 협소해지고 있다. 따라서 웨이퍼 단계에서 제조된 집적회로의 불량여부를 판단하기위한 검사 장비인 프로브카드(Probe Card)의 높은 집적도가 요구되고 있다. 하지만 기존의 MEMS 공법으로 제작되는 프로브 빔은 복잡한 제조 공정과 높은 생산비용, 낮은 집적도의 문제점을 가지고 있다. 본 연구에서는 이러한 문제점을 해결하기 위하여 간단한 제조 공정과 낮은 생산비용, 높은 집적도를 가지는 프로브 빔을 개발하기 위하여 절연절단 방식으로 BeCu (Beryllium-Copper) 프로브 빔을 제작하였다. 낮은 소비 전력으로 우수한 프로브 빔 어레이를 제작하기 위해서 가장 고려해야할 대상은 프로브 빔의 재료와 구조(형상)이다. 절연전단 방식으로 프로브 빔을 형성할 때 요구되는 Fusing current는 프로브 빔의 구조(형상)에 크게 영향을 받는다. 낮은 Fusing current는 소비 전력을 줄여주고, 절연절단으로 형성되는 프로브 빔의 단면(끝)을 날카롭게 하여 프로브 빔과 집적회로의 패드 간의 접촉 저항을 감소시킨다. 프로브 빔의 제작은 BeCu 박판을 빔 형태로 식각하여 제작하였으며, 실리콘 비아 홀(Via hole) 구조의 기판위에 정렬하여 soldering 공정을 통해 실리콘 기판과 BeCu 박판을 접합시켰다. 접합된 프로브 빔의 끝부분을 들어 올린 상태로 전류를 인가하여 stress free 상태로 만들어 내부 응력을 제거하였으며, BeCu 박판에 fusing current를 인가하여 BeCu 박판 프레임으로부터 제거를 하였다. 제작된 프로브 빔의 길이는 1.7 mm, 폭은 $50{\mu}m$, 두께는 $15{\mu}m$, 절단부의 단면적은 1$50{\mu}m^2$로 제작되었다. 그리고 프로브 빔의 절단부의 길이는 $50{\mu}m$ 부터 $90{\mu}m$까지 $10{\mu}m$ 증가시켜 제작되었다. 이후에 절연절단 공정에 요구되는 Fusing current를 측정하였고, 절연절단 후의 절단면의 형상을 SEM (Scanning Electron Microscope)장비를 통하여 확인하였다. 절단부의 길이가 $50{\mu}m$일 때 5.98A의 fusing current를 얻었으며, 절연절단 후 절단부 상태 또한 가장 우수했다. 본 연구에서 제안된 프로브 빔 제작 방법은 프로브카드 및 테스트 소켓(Test socket) 생산에 응용이 가능하리라 기대한다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.8
• /
• pp.1711-1716
• /
• 2012

Vocational rehabilitation is defined as a process which helps people with disabilities to maintain life of non-disabled people and vocational assessment is a part of it. Traditionally, vocational assessment is performed through using of assessment tools or vocational counseling, but assessment tools are very expensive and we should move to the facilities for the disabled. It is very efficient to apply vocational assessment to people with disabilities using the smart phones which users are expected to surpass thirty million in 2012, because it enables them to access anytime and anywhere. In this paper, we design and implement the mobile aptitude test system on android smart phone OS for people with disabilities. We develop the mobile aptitude test system using the Holland Test which is the assessment tool of career guidance and counseling.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2011.05a
• /
• pp.248-251
• /
• 2011

Vocational rehabilitation is defined as a process which helps people with disabilities to maintain life of non-disabled people and vocational assessment is a part of it. Traditionally, vocational assessment is performed through using of assessment tools or vocational counseling, but assessment tools are very expensive and we should move to the facilities for the disabled. It is very efficient to apply vocational assessment to people with disabilities using the smart phones which users are expected to surpass ten million in 2011, because it enables them to access anytime and anywhere. In this paper, we design and implement the mobile aptitude test system on android smart phone OS for people with disabilities. We develop the mobile aptitude test system using the Holland Test which is the assessment tool of career guidance and counseling.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.6
• /
• pp.52-58
• /
• 2014

In the present work, design optimization of film-cooling hole array on the pressure side of high pressure turbine nozzle was conducted. There are four rows of fan-shaped film cooling holes on the nozzle pressure side surface and each row has a straight array of holes in the spanwise direction for baseline model. For design optimization, hole distributions in streamwise and spanwise directions for three rows of holes except first row are parameterized as a 2nd-order shape function. Three-dimensional compressible RANS equations are used for flow and thermal analysis around the nozzle surface and optimization technique using Design of Experiment, Kriging surrogate model and Genetic Algorithm is used. The results shows that averaged adiabatic wall temperature at the whole nozzle surface decreases about 2.7% and averaged film cooling effectiveness at the pressure side of nozzle increased about 8.2%.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.2
• /
• pp.74-80
• /
• 2005

A new dimension measuring method for the measurement of diameter of an object has been developed using laser triangulation. The 3D data of an object was calculated from the 2 dimensional image information obtained by the laser stripe using the laser triangulation. The system that use existing theory can measure the diameter of hole not only in a normal plane but also ill an incline plane. However, in the existing theory, since the lens with fixed feral length was used, the area of measurement was fixed. The simplest way to solve this problem is to change distance between a CCD camera and object. Other way is to use a zoom lens having variable focal length. In this paper, the zoom lens with variable focal length was used. Therefore, we ran experiment with magnification that is optimized according to size of object using zoom lens with variable focal length.