• Journal of the Korea institute for structural maintenance and inspection
• /
• v.25 no.1
• /
• pp.25-32
• /
• 2021

For developing the durable eco-concrete, water-repellent and hydrophobic emulsion were prepared by stirring and mixing polymethyl hydrosiloxane and polyvinyl alcohol. After adding the PMHS emulsion cement paste, the hydration reaction characteristics and the change in chemical composition were analyzed through BSE and EDS analysis, and the micropores were evaluated by MIP test. Cement mixed with PMHS emulsion was analyzed to increase the hydration reactivity and to decrease the capillary porosity, but it was found that the capillary porosity varies depending on the degree of dispersion of the emulsion in the cement paste. In the case of the emulsion containing metakaolin, there was little difference in hydration degree and porosity from the case of using only the PMHS emulsion. However, when the cement surface was coated with PMHS emulsion, the contact angle was found to increase significantly compared to OPC, and it was analyzed that especially when PVA fiber was used together, it changed to a hypohydrophobic surface.

• Composites Research
• /
• v.35 no.6
• /
• pp.412-418
• /
• 2022

Flame-retardant vinyl ester (VE) resin films were developed from the mixtures of brominated and non-brominated epoxy resins via esterification with methacrylic acid without reactive diluents. The films were used to fabricate carbon fiber (CF) prepregs via a hot melt impregnation process. The viscosity of VE resins suitable for film production was optimized by mixing low-viscosity bisphenol-A and high-viscosity brominated bisphenol-A epoxy precursors. Increasing the bromine content of the cured VE resin further increased the limited oxygen index (LOI) (39%), storage modulus (2.4 GPa) at 25℃ and residual carbonization (16.1%) values compared to non-brominated VE. Manual layup of as-prepared VE prepregs with subsequent curing led to the successful fabrication of CF-reinforced composites with high tensile and flexural strength. The results from the study hold high promise for a styrene-free, environmentally friendly VE composite process in the future.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.1
• /
• pp.10-15
• /
• 2003

This study was carried out to investigate a radial distribution of moisture contents(MCs) within a log cross section(LC) during oven-drying of circumferential slices cut from some of domestic hardwoods LCs. For zelkova, the slices from sapwood and from transition part already reached to below hygroscopic range at 30% in average MC, whereas the innermost slice represented about 40% MC. A moisture gradient between the innermost slice and the adjacent slice from a cherry LC became severer with drying times. For castor aralia, the green MC for heartwood slices was approximately 23% higher than that for sapwood slices, and the similar moisture gradient still lasted until average 15% MC during oven-drying. For Chinese mahogany, the MCs of the mixed slices and the innermost slice were lower than those of the slices cut from the other parts during all over drying stage.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.6
• /
• pp.1035-1051
• /
• 2021

This study compares the strength properties of Jumchi-Hanjis dyed with 70% and 100% persimmon juice concentrations and undyed Jumchi-Hanjis. The Juumchi-Hanjis were made from Dakjis (mulberry papers), which were mixed with different ratios of fibers from paper mulberries originating in Korea and Thailand, including wood pulp from Canada. Research results showed that tensile, wet tensile, and bursting strengths of Jumchi-Hanjis dyed with 70% concentration were higher than those of undyed Jumchi-Hanjis. However, the tearing strengths of the dyed Jumchi-Hanjis were lower than those of undyed Jumchi-Hanjis. The wet tensile strengths of Jumchi-Hanjis dyed with 100% concentration were higher than those of dyed with 70% concentration. The increase and decrease of tensile, tearing, and bursting strengths depending on persimmon juice dyeing differed as per the mixing ratio of the raw materials of Jumchi-Hanjis. Dyeing with 100% persimmon juice concentration tends to be more useful than 70% to increase the tensile (MD) and wet tensile strengths of Jumchi-Hanjis containing only Korean mulberry fibers (90%) and wood pulp (10%) as raw materials. Dyeing with 100% concentration tends to be less useful than 70% to increase the tensile, tearing and bursting strengths of Jumchi-Hanjis with high proportions (90% or 60%) of mulberry fibers from Thailand.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.15 no.1
• /
• pp.53-61
• /
• 2013

To improve the quality of rice candy, We studied on manufacturng method and characteristic of rice candy by adding ratio of red ginseng marc. The results obtained were as follows: The boiled rice was added with 15 % malt extract to 1.2 times. After it was saccharified for 12 hours to 70℃, we concentrated it and made black rice candy. Then red ginseng marc was dried at 18% of moisture content and disrupted to 30 mesh below for manufacturing red ginseng marc's powder. Maintained at about 100℃, black rice candy added red ginseng marc's powder. These were mixed evenly and dried. Finally, rice candy adding red ginseng marc was completed. According to the characteristics of rice candy by adding red ginseng marc, the more amounts of red ginseng marc was increased, the less hardness and adhesiveness of rice candy was decreased. Also the brightness of the color difference was decreased. but yellowness and redness was increased. When adding red ginseng marc at 17.5%, it was evaluated to the good score in sensory evaluation.

• Clean Technology
• /
• v.16 no.4
• /
• pp.245-253
• /
• 2010

Optimum conditions for UV-radiated photopolymerization of unsaturated polyester that could be used as protecting layer of large diameter pipe were investigated in this paper. UV photopolymerization method was selected to solve the problems, arising when thermal polymerization by organic peroxide was used, such as the instability of peroxide initiator, the evolution of volatile organic compound, and thermal deformation of product. Two of the photo-initiators (Irgacure 819 and Darocure 1173) well known for its penetrating ability deep into the polymer layer were selected, and the optimum conditions for photopolymerization (1.5 phr initiator content, 1:1.2 initiator ratio, Ga lamp for UV source) were found from the thermal and mechanical test results of the resultant UP polymers. In addition, composite materials containing UP polymer and glass fiber were tested for hardness, impact strength, and flexural strength to find that the impact strength of composite significantly improved.

• Composites Research
• /
• v.22 no.3
• /
• pp.44-54
• /
• 2009

In this paper, we proposed a numerical model the complex permittivity for the E-glass fabric/epoxy composite laminate containing electrical conductive carbon black. The model is based on the percolation theory and for the composites over than the percolation threshold and in higher frequency band in that the AC conductivity is fully proportional to the frequency. The measurement for the complex permittivity wasperformed at the frequency band of 0.5 GHz $\sim$ 18.0 GHz using a vector network analyzer with a 7 mm coaxial air line. The proposed model is composed of the numerical equations of the scaling law used in percolation theory and constants obtained from experiments to quantify the model itself. The model describes the complex permittivity as the function of frequency and filler concentration. The model was verified by being compared with the measurements.

• Composites Research
• /
• v.37 no.2
• /
• pp.76-85
• /
• 2024

In this paper, a composite maintenance robot using carbon fiber spray method was developed that automatically sprays mixture was created for repair to damaged areas to repair them. To develop a robot, a repair process was developed in which a mixture of milled carbon fiber, epoxy resin, and hardener is sprayed and consolidated on the damaged area. To automate the repair process, an EOAT based on a collaborative robot was developed that can automatically suction and spray the mixture onto the damaged area. To evaluate the repair performance of the robot, 0° and 90° unidirectional specimens were manufactured and tested in accordance with ASTM D3039. Tests were performed on undamaged specimen, damaged specimen, and repaired specimen by a robot after damaged. As a result of the specimen test, the tensile strength of the 0° and 90° specimens was recovered by 10% and 90% after repair. Based on the test results, the repair performance of the developed composite maintenance robot was verified.

• Korean Journal of Agricultural Science
• /
• v.39 no.3
• /
• pp.335-340
• /
• 2012

During the manufacturing process of chestnut, 50% of biomass is produced as chestnut shell (CS) or chestnut hull (CH), a forestry by-product. Due to its high fiber content and economic benefit, there is a possibility of using chestnut hull as a supplement for a ruminant diet. Few studies, however, have been conducted on evaluating nutritive value of chestnut hull for ruminant animals. The objective of this study were thus to analyze chemical composition of CS, a by-product after the first processing of chestnut, and CH, a by-product after the second processing, and access in vitro rumen fermentation characteristics of them. For the in vitro fermentation using strained rumen fluid obtained from a fistulated Hanwoo steer, commercial total mixed ration (TMR) for dairy goat was used as a basal diet and was replaced with different proportions of chestnut shell and hull. A total number of 13 treatments were carried out in this study: 100% TMR, 100% CS, 100% CH, a mix with 50% CS and 50% of CH (MIX), TMR replaced with 5%, 10%, or 15% of CS, CH, or MIX, respectively. For each treatment, in vitro dry matter digestibility (IVDMD) and pH after 48 hours of rumen fermentation were measured. Gas production at 6, 12, 24, 48 hours of incubation was also analyzed. Compared to CH, CS contains higher level of fiber (NDF, ADF, lignin) and consequently has a lower amount of non-fiber carbohydrate, but no difference was observed in the other nutrients (i.e. crude protein, crude fat, and ash). IVDMD was significantly (p<0.05) the highest in 100% CH (71.97%) and the lowest in 100% CS (42.80%). Addition of CH by replacing TMR did not affect IVDMD, while an increase in the proportion of CS tended to decrease IVDMD. The total gas production after 48 hours of incubation and the rate of gas production were also the highest in 100% CH and the lowest in 100% CS (P<0.05). Likewise, the pH after 48 hours of fermentation was significantly (p<0.05) the lowest in 100% CH (6.33) and the highest in 100% CS (6.50), and no significant difference in gas production was observed when TMR was replaced with CS or CH up to 15% (P>0.05). In conclusion, CH may successfully be used for a supplement in a ruminant diet. The nutritive value of CS is relative low, but can replace, if not 100%, low quality forage. This study provides valuable information about the nutritive value of CS and CH. An in vivo trials, however, is needed for conclusively accessing the nutritive value of CS and CH.

• Journal of the Korean Arthroscopy Society
• /
• v.3 no.2
• /
• pp.85-90
• /
• 1999

Purpose : The purpose of this study is to evaluate the clinical and histological results of the osteoarthritic patients who had second look arthroscopy after microfracture surgery. Materials and Methods : From Oct. 1997 to Dec. 1998, 46 patients, 48 knees were treated by microfracture technique. In the 22 patients, 24 knees, 'second-look' arthroscopies and biopsies were performed at 6 months following microfracture. Three patients were men and 19 patients were women. Average age of the patients were 58 years (range, 40-75 years). The average follow up period was 12 months(7-20 months). We analysed clinical results according to the nine-point scale. Also we observed type II collagen formation with immunohistochemical staining. Results : Clinical results were excellent in 83% and good in 17%. Among the 24 knees, more than 80% areas of chondral defect were covered with regenerated cartilage in 21 knees. Histologically, the regenerated tissue appears to be a hybrid of hyaline cartilage and fibrocartilage. Regenerated cartilage contains variable amount of type II collagen with immunohistochemical staining. Conclusion : Most of the patients had significant improvement clinically. 'Second-look' showed that the chondral defect areas were covered with newly grown grayish white tissue. Microfracture in the full thickness chondral defect provides and enriched environment for cartilaginous tissue regeneration.