Proceedings of the Korean Society of Propulsion Engineers Conference
/
2002.04a
/
pp.59-59
/
2002
램제트 추진기관은 압축과정을 별도의 부품 없이 형상에 의해서 감속하여 연소 압력비를 얻는다. 따라서 구동 마하수와 형상에 의해 흡입과정의 압축 효율이 결정된다. 설계점은 충분한 유량을 확보 할 수 있는 유량과 충격파 각을 조절하여 전압력 손실을 줄이도록 고려되어야 한다. 또한 연소가 일어나면 연소실 압력이 배압으로 작용하고 비행시에 받음각은 변하므로 이에 따른 성능 분석도 고려 되어야 할 사항이다. 본 연구는 국내에서 실험한 형상에 대해 수치계산을 수행하여 코드의 검증과 아울러 램제트 유동장의 수치적 시뮬레이션도 설계단계에서 하나의 도구로 이용할 수 있음을 보여준다. 실험에서는 배압 조건을 얻기 위해 유동 블록키지를 유로 내에 두어 상응하는 배압을 얻었지만 본 계산에서는 압력 경계조건을 직접 사용하였다. 유동이 비정상 특성을 가지므로 시간 정확도를 이차로 가지도록 이중시간 전진법을 사용하였다. 사용한 압력비는 충격파가 카울 끝에 닿는 임계상태에 가까운 12, 13, 14에 대해 계산을 수행하였고 부스터모드로 흡입구 끝이 막혀 있다가 램제트 모드로 바뀌어 연소실 압력이 위의 압력비라고 가정할 때의 비정상 천이 과정을 계산해 보았다. 본 계산은 흡입구 부분만을 떼어놓고 적절한 가정 하에 수행되었지만 연소실 내부도 비정상 특성을 가지므로 흡입구와 연소실을 동시에 같이 계산해야한다. 추후에 전체적인 계산을 진행하기 위한 전 단계로 흡입구 계산만을 수행하여 실험과 잘 일치하는 계산 결과를 얻었고 전체 계산을 위한 연구는 진행 중에 있다.
Chang, Mu Seong;Choi, Byung Oh;Kang, Bo Sik;Park, Jong Won;Lee, Choong Sung
Transactions of the Korean Society of Mechanical Engineers A
/
v.37
no.9
/
pp.1169-1174
/
2013
Most products are indeed governed by multiple failure modes. However, there are few cases in which reliability analysis applies to only one failure mode at a time. Furthermore, reliability data do not include information about failure modes, or the reliability analysis is performed using a representative failure mode. The Weibull shape parameter for failure modes is more important than one for products in the reliability qualification test. This paper presents reliability analysis methods for a mechanical component with multiple failure modes. These methods include the competing failure modes (CFM) method and the mixed Weibull method. Pneumatic cylinder test data with three failure modes are presented to estimate the shape parameter for each separate failure mode. In addition, reliability measures (B10 life, characteristic life) of the pneumatic cylinder considering three failure modes were compared with those assuming a single failure mode.
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.50
no.3
/
pp.147-155
/
2022
The accumulated ice and snow during the operation of aircraft and railway vehicles can degrade aerodynamic performance or damage the major components of vehicles. Therefore, it is crucial to predict the temporal growth of ice for operational safety. Numerical simulation of ice is widely used owing to the fact that it is economically cheaper and free from similarity problems compared to experimental methods. However, numerical simulation of ice generally divides the analysis into multi-step and assumes the quasi-steady assumption that considers every time step as steady state. Although this method enables efficient analysis, it has a disadvantage in that it cannot track continuous ice evolution. The purpose of this study is to construct a surrogate model that can predict the temporal evolution of ice shape using reduced-order modeling. Reduced-order modeling technique was validated for various ice shape generated under 100 different icing conditions, and the effect of the number of training data and the icing conditions on the prediction error of model was analyzed.
A numerical study using linear finite element analysis is performed to investigate the behavior of basement wall subject to soil and water pressure. Currently, structural design of basement wall is based on the assumption for boundary condition of plate, which may lead to the erroneous results. In this study, parametric studies are performed to investigate the variation of moment and shear force according to column-to-wall stiffness ratios and aspect ratios. Scaled factors applicable to the design of basement wall are proposed with the illustration of desist examples.
Journal of the Computational Structural Engineering Institute of Korea
/
v.12
no.2
/
pp.185-199
/
1999
본 연구에서는 새로운 spline 유한대판 요소를 제안하였다. 제안된 정식화는 등매개 개념에 의해 기하학적 형상과 변위장을 가정함에 있어 길이방향은 3차의 B-spline 곡선으로, 횡방향에 대해서는 Lagrange 다항식에 의해 표현된다. 이 논문은 평판과 쉘해석에 있어서의 등매개 spline 유한대판 요소의 개선에 목적을 두고 있다. 이 새로운 요소는 스트립의 내부 절점에서 6개의 자유도를 갖는 합-응력 감절점 쉘 요소로부터 유도하였다. 스트립의 기하학적 형상은 강체 회전에 대한 정의에 위배되지 않고도 두께 방향을 따라 Jacobian이 일정하다는 가정을 따랐으며 고체역학에서 정의되는 면내 회전을 penalty 함수에 의한 구속조건으로 간주하여 면내 회전에 관계된 자유도를 생성하였다. 제안된 요소에 대하여 쉘의 전형적인 문제에 대한 수치예제를 보였으며 이 스트립 요소의 성능을 평가하였다.
Transactions of the Korean Society of Mechanical Engineers
/
v.11
no.3
/
pp.368-375
/
1987
Effective thermal conductivity of the porous nuclear fuel has been investigated numerically. Difficulties associated with irregular shape of pore have been overcome by using the Body Fitted Coordinate Systems. A computer code has been developed to solve the governing equation with appropriate boundary conditions by transforming from the Cartesian coordinates to the nonorthogonal curvilinear coordinates. The effects of the porosity have been investigated. For a convenient use of the result, a correlation equation was suggested under the assumption of circular pore. The computation results by the assumption of randomly oriented elliptic pore has been agreed more closely to existing experimental result than that by the assumption of circular pore.
In this paper, we present an algorithm which recognize hand shape in real time using only image without adhering separate sensor. Hand recognizes using edge orientation histogram, which comes under a constant quantity of 2D appearances because hand shape is intricate. This method suit hand pose recognition in real time because it extracts hand space accurately, has little computation quantity, and is less sensitive to lighting change using color information in complicated background. Method which reduces recognition error using principal component analysis(PCA) method to can recognize through hand shape presentation direction change is explained. A case that hand shape changes by turning 3D also by using this method is possible to recognize. Human interface system manufacture technique, which controls a home electric appliance or game using, suggested method at experience could be applied.
Journal of the Society of Naval Architects of Korea
/
v.29
no.1
/
pp.29-42
/
1992
A potential based panel method is used to predict the open water characteristics of spade-type rudders. The inflow velocity is assumed to be constant in lime and uniform in space. Source and dipole are distributed on the rudder surface. It is assumed that the wake surface is streaming from trailing edge and it is represented by dipole distribution. In this paper, wake geometry is assumed by imposing appropriate conditions at the trailing edge and far from the body. The effects of wake geometry are studied. The pressure Kutta condition is applied at the trailing edge, the effects of which are compared with those of two-dimensional Kutta condition. The results of calculations for a spade-type rudder are compared with published results. It is concluded that this approach shows fairly good agreement with experimental results and can be used in the initial design stage of a rudder.
Converging-diverging 노즐은 시스템 내부 유동에 적용되는 속도면적 법칙을 통해, 아음속 유동을 초음속으로 만드는 장치이며, 항공기 엔진 등에서 추력을 얻기 위해 쓰인다. 이상기체, 등 엔트로피를 가정한 동일 입구 조건에서, 출구로 빠져나오는 유동의 속도는 오직 면적 비에만 관계한다. 그러나 실제현상에서는, 출구에서의 유속이 유동의 압축성 효과 및 벽면에서의 전단력 등으로 인해 노즐 형상마다 상이한 결과를 낳는다. 본 연구에서는 EDISON Simulation을 활용하여 다양한 노즐 형상에 따른 출구에서의 Mach number를 구하고, 각각의 결과로부터 경향성을 찾는다. 또, 계산 결과를 이론식을 통해 도출되는 결과와 비교한다.
초임계 익형은 천음속 영역에서 비행하는 상업용 민간 항공기와 전투기 날개의 공력성능을 향상시키기 위해 Whitcomb R. T.가 제안 하였다. 초임계 익형은 상부표면을 평평하게 디자인하여 임계마하수보다 큰 마하수에서 나타나는 익형 주위의 충격파 출현을 지연시킴으로써 항력을 줄일 수 있고, 상부 표면의 평면 설계로 인한 양력 감소를 보정하기 위하여 하부 표면의 꼬리부분에 캠버가 있는 형상을 하고 있다. 본 연구에서는 EDISON CFD를 이용하여, 초임계 익형의 공력특성을 해석하고 Xfoil의 data와 비교 분석하였다. 또한, 초임계 익형의 형상을 변경하여 두께와 뒷전 캠버가 다른 초임계 익형을 설계하였다. 새로운 초임계 익형의 형상은 상용 프로그램 Maple12을 이용하여 Whitcomb Integral Supercritical Airfoil의 형상을 수정하여 구할 수 있다. 초임계 익형 주위의 유동을 2D압축성 유동으로 가정하고 EDISON CFD의 2D_Comp-2.0 솔버를 사용하여 수치해석을 수행하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.