• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.05a
• /
• pp.168-169
• /
• 2015

금속 박막과 폴리머 기판 사이에 접착력을 증대시키는 방법으로 금속-폴리머 계면에 나노 임프린트 구조체를 이용하는 방식을 최초로 이용하였다. 나노선 어레이 형상을 가진 몰드와 열 임프린트 방식을 이용하여 폴리머 기판 표면 위에 나노선 어레이 형상을 임프린트 하고, 열 증착 방식으로 금속 박막을 올렸다. 본 연구에서 제작된 금속-임프린트 폴리머 계면에서 높은 기계적 굽힘성 및 접착력을 가지는 것을 확인하였다.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.3
• /
• pp.35-47
• /
• 1996

A surface panel method treating a boundary-value problem of the Dirichlet type is presented to design a three dimensional body with free surface corresponding to a prescribed pressure distribution. An integral equation is derived from Green's theorem, giving a relation between total potential of known strength and the unknown local flux. Upon discretization, a system of linear simultaneous equations is formed including free surface boundary condition and is solved for an assumed geometry. The pseudo local flux, present due to the incorrect positioning of the assumed geometry, plays a role f the geometry corrector, with which the new geometry is computed for the next iteration. Sample designs for submerged spheroids and Wigley hull and carried out to demonstrate the stable convergence, the effectiveness and the robustness of the method. For the calculation of the wave resistance, normal dipoles and Rankine sources are distributed on the body surface and Rankine sources on the free surface. The free surface boundary condition is linearized with respect to the oncoming flow. Four-points upwind finite difference scheme is used to compute the free surface boundary condition. A hyperboloidal panel is adopted to represent the hull surface, which can compensate the defects of the low-order panel method. The design of a 5500TEU container carrier is performed with respect to reduction of the wave resistance. To reduce the wave resistance, calculated pressure on the hull surface is modified to have the lower fluctuation, and is applied as a Dirichlet type dynamic boundary condition on the hull surface. The designed hull form is verified to have the lower wave resistance than the initial one not only by computation but by experiment.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.176-179
• /
• 2009

ZnO:Al 투명전도막을 유리기판위에 in-line RF-magnetron sputtering법으로 증착온도 및 증착압력에 따라 제조하고, 습식식각에 따른 박막의 표면형상 및 광학적 특성변화를 조사하였다. 초기박막은 육방정계(Hexanonal wurtzite)의 결정 구조와 (002)면의 c-축 우선배향성을 갖으며 가시광 영역에서 높은 광 투과도(T $\geq$ 80%)와 낮은 비저항($\rho\;=\;5.2{\times}10^{-4}{\Omega}{\cdot}cm$)의 특성을 나타내었다. 습식 식각 후 박막의 표면형상은 식각 전 박막의 결정성에 큰 의존성을 보이며 본 연구에서는 1 mTorr의 낮은 증착압력과 $350^{\circ}C$의 높은 증착온도에서 증착된 결정성이 우수한 막에서 높고 균일한 형태의 crater를 갖는 표면형상을 얻을 수 있었다. 균일한 crater를 형성하는 ZnO:Al 박막은 hill 형태의 표면형상을 갖는 상용 Asahi-U glass에 비하여 높은 Haze ($T_{diffused}/T_{total}$)값과 넓은 산란각을 나타내어 향상된 광 산란특성을 갖으며 이는 실리콘 박막 태양전지내로 입사된 광의 산란경로를 증가시켜 태양전지 성능을 크게 향상시킬 수 있을 것으로 기대한다.

• Journal of Wetlands Research
• /
• v.14 no.4
• /
• pp.457-469
• /
• 2012

Bedform data at 4 shallow zones in the Yellow Sea where waves as well as tidal range are high and bed material is relatively coarse were collected and analyzed here. Water depths in the study area where the bedform data were collected are 10 ~ 65 meters, and ripple lengths well developed are between 6 ~ 13 meters. Existing empirical formula for prediction of ripple length as for coexistence of waves and currents include Khelifa and Ouellet(2000) and Soulsby(2005), both of which have been based on laboratory measurements, or field measurements at different physical environment from the Yellow Sea with respect to tidal range, wave strength, and bed material. New scaling factors are proposed here for better prediction of the ripple length on coastal zone in the Yellow Sea.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.12
• /
• pp.1641-1646
• /
• 2011

The second-generation magnetic abrasive polishing is one of the nontraditional machining technologies newly developed. Because of the flexibility effect in magnetic abrasive polishing, the precise and mirror like surface can be obtained during this process. In this study, magnetic abrasive polishing process was applied in small grooved surface. As a result, it was seen that the flexible magnetic abrasive tool was effective to remove burrs on the edge of the groove. However, the efficiency of magnetic abrasive polishing at the slot was very low according to increasing depth and width of slot. So, correlation between geometric parameters, such as the depth and width, and surface roughness was evaluated and the minimum width for suitable polishing was found by experimental results.

• Journal of the Korean Institute of Gas
• /
• v.16 no.3
• /
• pp.65-70
• /
• 2012

Experimental investigations were carried out to examine the explosion characteristics by different sizes in the wall surface shape of a water gel barrier in an explosion chamber, 1,600 mm in length with a square cross-section of $100{\times}100\;mm^2$. The sizes in the wall surface shape were varied by using water gel barriers with a cross-section of $100{\times}200\;mm^2$ and its were varied in the bottom of the chamber away 300, 700 and 1,100 mm, respectively from the closed end of the chamber. The flame propagation images were photographed with a high speed camera and the pressure was recorded using a pressure transducer and a data acquisition system. It was found that as the size of the wall surface shape increased, the flame propagation process and the time taken to reach the maximum pressure were found to be faster. As a result, both the flame speed and the explosion overpressure increased as the size of the wall surface shape increased.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.103-103
• /
• 2009

플라스틱 기판위에 스퍼터링과 열 기상증착법을 이용하여 코팅된 주석 박막을 관찰하여 주석 박막의 형상 변화에 영향을 미치는 공정 요인을 알아보았다. 열 기상증착법에 의해 코팅된 주석 박막은 주석 소스의 양에 따라 쉽게 형상을 제어할 수 있었다. 하지만 박막과 기판의 부착력이 낮아 쉽게 박리가 일어났다. 스퍼터링으로 콘팅된 주석 박막은 기판과 부착력은 높았으나 코팅 시 인가된 전원의 세기, 코팅 시간, 코팅 시 진공도등 다양한 공정인자 조절에도 불구하고 형상에 큰 변화는 관찰하지 못하였다. 전원의 세기가 증가하면 주석의 섬 크기가 증가하고 코팅 시간이 늘어나면 전원의 세기가 증가한 것과 유사한 형상 변화가 있어다. 주석 박막 코팅 시 공정 압력은 낮추면 주석 섬의 크기가 감소하였는데 이는 스퍼터된 주석 이온의 평균 자유 행로가 길어져 비교적 작은 핵형성에 의해서 나타난 현상으로 판단된다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.326-326
• /
• 2011

반도체 소자의 집적화/소형화에 따라, 낮은 비저항을 가진 구리(Cu)를 이용한 배선공정에 관한 연구가 활발하게 진행되고 있다. 구리배선 공정에 있어 전기 도금법이 다양하게 적용됨에 따라, 구리도금 박막 형성을 위해 사용되는 Cu seed 층의 상태는 배선으로 형성된 Cu박막 특성에 크게 영향을 미친다 [1-3]. 본 연구에서는 sputter 방식으로 증착된 Cu seed 층(Cu seed / Ti / Si) 위에 형성된 자연산화막을 제거하기 위하여 다양한 세정방법을 도입하여 비교 분석하였다. 계면활성제인 TS-40A를 비롯한 NH4OH 용액과 H2SO4 용액을 사용하여 Cu seed 층 위에 형성된 구리산화막을 제거함으로서 형성된 표면형상 및 표면상태를 조사분석 하였다. FE-SEM (Field Emission Scanning Electron Microscope)을 이용하여 표면 처리된 Cu seed층 표면의 형상 및 roughness 등을 측정하였고, XPS (X-ray Photoelectron Spectroscopy)를 이용하여 표면 처리된 Cu seed 표면의 화학구조 및 불순물 상태를 조사하였다.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.2 no.1
• /
• pp.1-9
• /
• 1992

Radiation heat transfer was calculated for initial stage of crystal growth in Czochralski crystal growth system. View factors among surface elements were calculated for the estimation of heat evolution and all the surfaces were assumed to be diffuse-gray. The values of view factors were greatly different along the position of surface elements. The dissipated amounts of heat flux from the melt surface were 3.6 times larger than those from the crystal surface at the initial stage of crystal growth and this amounts were greater when the surface elements were not considered. The trijunction part of the crystal was greatly affected by the melt surface near the crystal. Consequently radiation heat transfer between surface elements must be considered in order to correctly simulate the initial crystal growth.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.8
• /
• pp.1048-1054
• /
• 2011

Laser surface hardening process is the method of hardening surface by inducing rapid self quenching of laser injected area through transfer of surface heat to inside after rapid heating of laser injected area only by high density energy heat source. This surface treatment method does not involve virtually any thermal deformation by heat treatment nor accompanies any other process after surface hardening treatment. In addition, allowing local machining, this method is a surface treatment method suitable for die with complicated shape. In this study, die material cast iron was surface-treated by using high power diode laser with beam profile suitable for heat treatment. Since the shapes of die differ by press die process, specimens were heat-treated separately on plane and corner depending on the applied parts. At this time, corner heat treatment was done with optic head inclined at $10^{\circ}$. As a result, corner heat treatment easily involves concentration of heat input due to limitation of heat transfer route by the shapes compared with plane part, so the treatment accomplished hardening at faster conveying speed than plane heat treatment.