• Journal of the Korean Electrochemical Society
• /
• v.18 no.1
• /
• pp.7-16
• /
• 2015

Effects of chemical composition ($Cu^{2+}$, $K_4P_2O_7$ and additive concentrations) of baths on properties of Cu thin films electrodeposited from pyrophosphate copper bath were investigated. Current efficiency was increased to be near 100% with increasing $Cu^{2+}$ concentrations from 0.02 to 0.3M. Decrease of current efficiency was observed in the range of 1.5~1.8M $K_4P_2O_7$ concentration, but current efficiency of about 100% was measured in the ranges of both 0.9~1.3M and 2.1~2.4M. The change of additive concentration did not influenced current efficiency. Residual stress of electrodeposited Cu thin films was measured to be about 20 MPa below 0.15 M $Cu^{2+}$ concentration and increased with the increase of it to 0.25 M. Maximum residual stress of 120MPa was observed at 0.25M $Cu^{2+}$ concentration. On the other hand, residual stress decreased from 80 to near 0 MPa as $K_4P_2O_7$ concentration varied from 0.9 to 2.4M and but The change of additive concentration did not affected on residual stress. $Cu^{2+}$ and $K_4P_2O_7$ concentrations significantly affect on surface morphology of electrodeposited Cu thin films, but additive concentration slightly affected. From XRD analysis, the microstructures of electrodeposited Cu thin film was affected from the changes of $Cu^{2+}$ and $K_4P_2O_7$ concentrations, but not from that of additive concentration. Strong preferred orientation of (111) peak was observed with increasing $Cu^{2+}$ and $K_4P_2O_7$ concentrations.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.231-240
• /
• 2017

Recently, there have been frequent occurrences of ground sink in the urban area, which have resulted in human and material damage and are accompanied by economic losses. This is caused by artificial factors such as soil loss, poor compaction, horizontal excavation due to the breakage of the aged sewage pipe, and lack of water proof at vertical excavation. The ground sink can be prevented by preliminary restoration and reinforcement through exploration, but it can be considered that it is not suitable for urgent restoration by the existing method. In this study, a model experiment was carried out to simulate the in-ground cavities caused by groundwater flow for developing non-excavation urgent restoration in underground cavity and the range of the relaxation zone was estimated by detecting the around the cavity using a relaxation zone detector. In addition, disturbance region and relaxation region were separated by injecting gypsum into cavity formed in simulated ground. The shape of the underground cavity due to the groundwater flow was similar to that of the failure mode III formed in the dense relative density ground due to water pipe breakage in the previous study. It was confirmed that the relaxed region detected using the relaxation zone detector is formed in an arch shape in the cavity top. The length ratio of the relaxation region to the disturbance region in the upper part of the cavity center is 2: 1, and it can be distinguished by the difference in the decrease of the shear resistance against the external force. In other words, it was confirmed that the secondary damage should not occur in consideration of the expandability of the material used as the injecting material in the pre-repair and reinforcement, and various ground deformation states will be additionally performed through additional experiments.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.1
• /
• pp.9-18
• /
• 2015

Purpose: The purpose of this study is to examine characteristics of implant surface with RBM and anodizing treatments, and to evaluate the responses of osteoblast-like cell (MG-63 cell). Materials and methods: Grade IV titanium disks were fabricated (Diameter 10 mm, thickness 3 mm). Anodizing treatment (ASD) group, RBM and anodizing treatment (RBM/ASD) group, control (machined surface) group were divided. In this study, osteoblast-like cell was used for experiments. The experiments consist of surface characteristics evaluation by FE-SEM images, energy dispersive spectroscopy and stereo-SEM. In order to evaluate cell adhesion evaluation by crystal violet assay and observe cells form by confocal laser microscopy. To assess cell proliferation by XTT assay, cell differentiation by RT-PCR and mineralization by Alizarin red S stain assay. ELISA analyzer was used for Quantitative evaluation. Comparative analysis was run by one-way ANOVA (SPSS version 18.0). Differences were considered statistically significant at P<.05. Results: In ASD group and RBM/ASD group, the surface shape of the crater was observed and components of oxygen and phosphate ions in comparison with the control group were detected. The surface average roughness was obtained $0.08{\pm}0.04{\mu}m$ in the control group, $0.52{\pm}0.14{\mu}m$ in ASD group and $1.45{\pm}0.25{\mu}m$ in RBM/ASD group. In cell response experiments, ASD group and RBM/ASD group were significantly higher values than control group in cell adhesion and mineralization phase, control group was the highest values in the proliferative phase. In RT-PCR experiments, RBM/ASD group was showed higher ALP activity than other groups. RBM/ASD group in comparison with ASD group was significantly higher value for cell adhesion and proliferation phase. Conclusion: In the limitation of this study, we are concluded that the surface treatment with RBM/ASD seems more effective than ASD alone or machined surface on cellular response.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.33 no.4
• /
• pp.38-51
• /
• 2015

In the maps of the period, there were three large ponds called Dongji(東池), Seoji(西池) and Namji(南池) in Hanyang, the capital of Joseon Dynasty. They were different than the ponds found in the palace, civic buildings, and private dwellings. Dongji, Seoji and Namji were ponds relating to Fortress wall of Seoul, and all had lotuses cultivated in them. The purpose of this paper is to clarify the locational and spatial characteristics of these ponds and to detail the construction and reconstruction process and management conditions through maps, drawings, illustrations, historical records and literary works from the urban environmental perspective. The results are as follows. First, Seoji and Namji were intended for Bibo(裨補) which redeemed the geographical weaknesses of Hanyang, securement of bright court water(明堂水), supplement for fire energy(火氣), fire preventive water and waterscape facilities, while Dongji was emphasized on protecting water mouth(水口) besides Bibo and securement of bright court water. Second, Seoji was connected to mountain streams and Dongji and Namji were to ditches. The ponds connected to ditches had been difficult to fill and maintain. Third, Seoji and Namji were in urban areas, whereas Dongji was in farmlands, and these locational differences had an influence on the use of ponds. Fourth, the shapes of ponds, in contrast to the ponds in palace and civic buildings, which were perfectly square, were either freeform or square with rounded edges. Fifth, lotus ponds could be maintained by continuous management polices, earth filling and reconstructing process were repeated during the Joseon Dynasty. The lotus ponds of Fortress Wall of Seoul which had managed over 500 years, were built in, in accordance with the tenets of Bibo pungsu geomancy; however as time passed, they were maintained not only as public open spaces, but also a cultural attraction for residents and visitors.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.28 no.5
• /
• pp.211-216
• /
• 2018

The recovery of rare earth elements (REE) including La, Nd and Ce from spent batteries is important issues to reuse scarce resources. Herein, we present a simple recovery process to obtain lanthanum oxide ($La_2O_3$) from spent Ni-MH batteries, and demonstrate the conversion mechanism from $NaLa(SO_4)_2{\cdot}H_2O$ to $La_2O_3$. This strategy requires the initial preparation of $NaLa(SO_4)_2{\cdot}H_2O$ and subsequent metathesis reaction with $Na_2CO_3$ at $70^{\circ}C$. This metathesis reaction resulted in the crystalline lanthanum carbonate hydrate ($La_2(CO_3)_3{\cdot}xH_2O$) powder with plate-like morphology. On the basis of TGA result, the $La_2(CO_3)_3{\cdot}xH_2O$ powder was calcined in air at three different temperatures, that is, $300^{\circ}C$, $500^{\circ}C$, and $1000^{\circ}C$. As the calcination temperature increased, the morphology of powder was changed; prism-like ($NaLa(SO_4)_2{\cdot}H_2O$) ${\rightarrow}$ platelike ($La_2(CO_3)_3{\cdot}xH_2O$) ${\rightarrow}$ aggregated irregular shape ($La_2O_3$). Futhermore, XRD results indicated that the crystalline $La_2O_3$ could be synthesized after the metathesis reaction with $Na_2CO_3$, followed by heat-treatment at $1000^{\circ}C$, along with a change of crystallographic structures; $NaLa(SO_4)_2{\cdot}H_2O$ ${\rightarrow}$ $La_2(CO_3)_3{\cdot}xH_2O$ ${\rightarrow}$ $La_2O_3$.

• Economic and Environmental Geology
• /
• v.52 no.6
• /
• pp.627-635
• /
• 2019

Cement-asbestos slate is the main asbestos containing material. It is a product made by combining 10~20% of asbestos and cement components. Man- and weathering-induced degradation of the cement-asbestos slates makes them a source of dispersion of asbestos fibres and represents a priority cause of concern. When the asbestos enters the human body, it causes cellular damage or deformation, and is not discharged well in vitro, and has been proven to cause diseases such as lung cancer, asbestos, malignant mesothelioma and pleural thickening. The International Agency for Research on Cancer (IARC) has designated asbestos as a group 1 carcinogen. Currently, most of these slats are disposed in a designated landfill, but the landfill capacity is approaching its limit, and there is a potential risk of exposure to the external environment even if it is land-filled. Therefore, this study aimed to exam the possibility of detoxification of asbestos-containing slate by using exothermic reaction and heat treatment. Cement-asbestos slate from the asbestos removal site was used for this experiment. Exothermic catalysts such as calcium chloride(CaCl₂), magnesium chloride(MgCl₂), sodium hydroxide(NaOH), sodium silicate(Na₂SiO₃), kaolin[Al₂Si₂O₅(OH)₄)], and talc[Mg₃Si₄O₁₀(OH)₂] were used. Six catalysts were applied to the cement-asbestos slate, respectively and then analyzed using TG-DTA. Based on the TG-DTA results, the heat treatment temperature for cement-asbestos slate transformation was determined at 750℃. XRD, SEM-EDS and TEM-EDS analyses were performed on the samples after the six catalysts applied to the slate and heat-treated at 750℃ for 2 hours. It was confirmed that chrysotile[Mg₃Si₂O₅(OH₅)] in the cement-asbestos slate was transformed into forsterite (Mg₂SiO₄) by catalysts and heat treatment. In addition, the change in the shape of minerals was observed by applying a physical force to the slate and the heat treated slate after coating catalysts. As a result, the chrysotile in the cement-asbestos slate maintained fibrous form, but the cement-asbestos slate after heat treatment of applying catalyst was broken into non-fibrous form. Therefore, this study shows the possibility to safely verify the complete transformation of asbestos minerals in this catalyst- and temperature-induced process.

• Analytical Science and Technology
• /
• v.28 no.6
• /
• pp.398-408
• /
• 2015

Carbon monoxide (CO) intoxication, arising from CO from an ignited charcoal briquette (ICB), is a popular means of committing suicide in Korea. Most CO intoxications are related to suicide attempts; however, the possibility of a homicide disguised as a suicide cannot be ruled out. Therefore, forensic investigation of the deceased and the crime scene is crucial to confirm that the deceased committed suicide. Detection of the components of an ICB on the objects suspected of being contacted by the deceased, such as the hands, nostrils, and doorknobs, is essential for linking the crime scene to the victim in the case of suicides by ignited ICBs. The traces from an ICB were analyzed by investigating the morphological characteristics and obtaining elemental compositions. The ICBs were completely different from blackened wood, as detected by discriminant analysis with the elements of carbon and oxygen. We analyzed one case of CO intoxication to demonstrate an excellent procedure for verifying whether a suicide occurred with an ICB. We employed SEM-EDX for the analysis of an ICB, microscope-FT/IR and pyrolysis-GC/MS for a partly burnt resin-type substance, GC/MS for diphenhydramine (a sleeping drug), and GC/TCD for the CO-Hb level. We detected traces of an ICB on the hands, nostrils, and doorknobs, which were all discriminated into an ICB group. Detection of ICB traces from the nostrils could indicate that the deceased started the fire themselves to commit suicide. The partially burnt black material was analyzed as an acrylronitrilestyrene polymer, which is normally used to make bags for carrying or wrapping and could be assumed to have been used to transport the ICB. Diphenhydramine, a sleeping drug, was detected at a level of 2.3 mg/L in the blood, which was lower than that in fatal cases (8-31 mg/L; mean 16 mg/L). A CO-Hb level of 79% was found in the blood, which means that the cause of death was CO intoxication. The steps shown here could represent an ideal method for reaching a verdict of suicide by CO intoxication produced by burning an ICB in a sealed room or a car.

• Korean Journal of Plant Resources
• /
• v.20 no.1
• /
• pp.22-27
• /
• 2007

Effects of prunella vulgaris L., chrysanthemum indicum L. and pueraria Radix on plasma lipid composition and histological consideration were investigated in hyperlipidemic rats. Concentration of plasma ${\beta},-lipoprotein$ showed a tendence to decrease in prunella vulgaris L., chrysanthemum indicum L. and pueraria Radix treatment groups. However these values were showed not significantly different from control group. Concentration of plasma FFA in prunella vulgaris L., chrysanthemum indicum L. and pueraria Radix treatment groups showed a lower values compared to control group and concentration of plasma FFA of prunella vulgaris L. and pueraria Radix treatment group showed a lower values than prunella vulgaris L. and chrysanthemum indicum L. treatment group. Concentration of plasma glucose and triglyceride showed a tendence to decrease in prunella vulgaris L., chrysanthemum indicum L. and pueraria Radix treatment groups. However plasma glucose values showed not significantly different from control group. Plasma total cholesterol concentration showed a low and HDL-cholesterol concentration showed a high in prunella vulgaris L. and pueraria Radix treatment group. However LDL-cholesterol concentrations were not significantly different in treatment groups. Histological consideration of heart, liver and kidney in prunella vulgaris L. and pueraria Radix treatment groups showed a good features in fat accumulation condition than those of other treatment groups. However in the condition of high fat accumulation in tissues, heart, liver and kidney were showed a slight congestion and a bashed cell nucleus.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.12 no.1
• /
• pp.64-72
• /
• 2009

The method to generate a digital elevation model(DEM) from contour lines causes a problem in which the low relief landform cannot be clearly presented due to the fact that it is significantly influenced by the expression of micro landform elements according to the interval of contours. Thus, this study attempts to develop a landcover burning method that recovers the micro relief landform of the DEM, which applies buffering and map algebra methods by inputting the elevation information to the landcover. In the recovering process of the micro landform, the DEM was recovered using the buffering method and elevation information through the map algebra for the landcover element for the micro landform among the primary DEM generation, making landcover map, and landcover elements. The recovering of the micro landform was applied based on stream landforms. The recovering of landforms using the buffering method was performed for the bar, which is a polygonal element, and wetland according to the properties of concave/convex through generating contours with a uniform interval in which the elevation information applied to the recovered landform. In the case of the linear elements, such as bank, road, waterway, and tributary, the landform can be recovered by using the elevation information through applying a map algebra function. Because the polygonal elements, such as stream channel, river terrace, and artificial objects (farmlands) are determined as a flat property, these are recovered by inputting constant elevation values. The results of this study were compared and analyzed for the degree of landform expression between the original DEM and the recovered DEM. In the results of the analysis, the DEM produced by using the conventional method showed few expressions in micro landform elements. The method developed in this study well described wetland, bar, landform around rivers, farmland, bank, river terrace, and artificial objects. It can be expected that the results of this study contribute to the classification and analysis of micro landforms, plain and the ecology and environment study that requires the recovering of micro landforms around streams and rivers.

• The korean journal of orthodontics
• /
• v.28 no.1 s.66
• /
• pp.43-49
• /
• 1998

The aim of this study were to measure and compare the stress level on three type brackets and each other material (stainless steel, ceramic) with tipping and torquing forces by using the finite element analysis and to design biomechanically favorable brackets. For this study, three kinds of brackets were selected(A:Transcend-RMO, B:Signature-Unitek, C:PAW: plain archwire appliance-applied for a patent in Yonsei Udiversity). The slot size of bracket was 0.022inch and the size of archwire was 0.0175x0.025inch and taper shaped archwire was used in PAW. Loading force in tipping was 4.27N and torquing force was 32.858N applied by archwire torsion with 19.7degree and 11.3 degree in C type bracket. The conclusions were that (1) The finite element method proved to be a useful tool in the stress analysis of orthodontic bracket subjected to various forces. (2) With tipping, the stresses were concentrated at the gingival wall of the wire slot where it meets the mesial bracket surface and the incisal wall of the wire slot where it meets the distal bracket surface and with torquing, the stresses were concentrated at the junction of the gingival or incisal wall and base of the slot. (3) The maximum stress value was higher in torquing force than tipping force and therefore it is desirable to design on the basis of torquing force. (4) It was considered that the change in material might be affect on the diminish of stress value in the place of stess concentration. (5) The maximum stress value was highest on PAW bracket when the tipping and torquing force was applied and therefore it would be desirable to use mechanically favorable material on PAW bracket.