• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2004.05a
• /
• pp.454-457
• /
• 2004

The high degree of uncertainty in customer demands forces companies of today to equip with a flexible and adaptable structural organization. It also has an influence on the configuration of the company's supply chains, since the members in supply chains are dependent to the goods customers need. If a company can not come up with the customers' requirements and their level of satisfaction, the competitiveness of the company will be weaken in the market places. To meet such conditions, therefore, reconfiguration of supply chains should be considered as an important factor in a complex, dynamic, and fluctuating market environment. In this paper, therefore, we have adapted a fractal concept to SCM to facilitate reconfiguration of supply chains. To do so, we have first introduce fractal-based SCM, referred to as fSCM. Then, we have described definitions of the reconfigurability in supply chains and the methodology of Dynamic Restructuring Process (DRP) in supply chains including specific strategies and constraints. An exemplary model will also be briefly illustrated to demonstrate how supply chains conduct DRP autonomously.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.1 s.94
• /
• pp.68-74
• /
• 1999

One of the recent changes in machining technology is rapid application of micro- and high precision grinding processes. A fine groove generation is necessary for the fabrication of optic, electronic and semiconductor parts, and achieved by chemical or mechanical processes. Slot grinding is very efficient for the generation of micro ordered groove with hard and brittle materials. As slot grinding is continuous, the ground depth become gradually shallow because of wheel wear. The form accuracy become worse from the increase of ground slot width by the loading phenomena at wheel side, results on chipping damage of the workpiece. The experiments achieve to the enhancement of the form accuracy and chipping free of the brittle materials using V shaped cast iron bonded diamond wheels. In this study we focused on the investigation of the effect of the high pressure air jet on the grinding characteristics. As a results, we found that the high pressure air jet is very effective on the reductions of the wheel wear, enhancement of the form accuracy.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.43-50
• /
• 2000

A CBN wheel was used for the highly efficient and precision grinding of the mold material(STD11). The grinding form accuracy by a CBN wheel is very excellent due to its low wheel wear, but grinding fragments resemble fine powders rather chips. A fine powders by this fragmentation can easily get attached to the wheel surface and therefore causing a loading. In order to prevent this fragmentation phenomena, the alumina stick is use to processing. Because the dressing with alumina stick should be interrupted for a processing, the automation of the processing and high productivity was very difficult. The investigation on the effect of Ultrasonic In-Process Dressing(ULID) on the grinding characteristics focuses in this Paper. This ULID method is that ultrasonic vibration in my Position of wheel is used to remove impurities on the wheel surface. Finally, the rate of surface roughness change in grinding by the ULID method was less than grinding without ultrasonic vibration. Loading phenomena by the ULID method were more prevented than grinding without ultrasonic vibration.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.516-519
• /
• 2004

As the optical communication industry is developed, the demand of optical communication part is increasing. ZrO$_2$ ceramic ferrule is very important part which can determines the transmission efficiency and information quality to connect the optical fibers. In general ZrO$_2$ ceramic ferrule is manufactured by grinding process because the demands precision is very high. And the co-axle grinding process of ZrO$_2$ ceramic ferrule is to make its concentricity all of uniform before centerless grinding. This paper deals with the analysis of the process parameters such as grinding wheel speed, grinding feedrate and regulating wheel speed as influential factors, on the concentricity and surface finish developed based on Taguchi's experimental design methods. Taguchi s tools such as orthogonal array, signal-to-noise ratio, factor effect analysis, etc. have been used for this purpose optimal condition has been found out. Thus, if possible be finding highly efficient and quality grinding conditions.

• IE interfaces
• /
• v.23 no.2
• /
• pp.182-192
• /
• 2010

Customer needs for final products are very unpredictable because product specifications and technologies are being improved very quickly thereby their requirement level is also elevated correspondingly. In order to survive and to enhance competitiveness in the global market, many manufacturing companies are trying to find a breakthrough from collaborization. Even though they want to collaborate with others, however, they do not exactly know what kind of system they have to develop or which technology they have to use. In this paper, therefore, we first investigate status and trend of information systems and infrastructure that are essential for collaboration. We then clearly describe definition and classification of collaboration with various point of views considering collaboration pattern, timing condition of collaborative activities, organizational structure, etc. With web-based collaboration systems already developed by i-Manufacturing (Korean-style Manufacturing Innovation) project, led by Korean government from 2004, we introduce main functions and analyze collaboration types of each system. Strategically important technologies for supporting collaboration will also be illustrated by reorganizing collaborization technologies after evaluating them with respect to emergency and importance of each technology. We hope this research will provide a guideline on collaboration especially for small and medium sized manufacturing companies.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.793-797
• /
• 2000

The environmental problems by using coolant demanded the new cooling methods. As one of them the studies on the dry grinding with compressed cold air have been done. The cooling method using compressed cold air was effdve thmugh going down the temperature of compressed air supplied below $-25^{\circ}C$ and inneasing the amount of mmpresd cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using MQL(Minimum Quantity Lubrication) or mist newly were suggested. These two methods can satisfy both cooling effect and lubrication with only small amount of coolant, also has the benefit in the point of decreasing the envimnmental pollution. This paper focused on analyzing the grindmg characteristics of the cooling method using mid. The generated heat and grinding force of the cooling method using mist were compared with them of coolant and compressed cold air. And them grinding test according to the temperature of compressed cold air, mist spray amount and mist supply direction were done.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.968-973
• /
• 2003

As environmental restrictions have continuously become more strict, it has emphasized development of environment-friendly technologies. In cutting technology, it has been well recognized that cutting fluids might have undesirable effects on worker's health and working environment and, hence, recently there have been numerous attempts to minimize harmful effects of cutting fluids on environments. To minimize the use of cutting fluids in machining, conventional cutting fluids have been replaced with the technologies of pressurized cold air and minimum quantity lubrication(MQL). Compared with milling, turning is a continuous cutting process, where tools are continuously heated up and lack of lubricity could lead to tool wear and deteriorated surface roughness. In this study, it has been investigated how tool wear and surface roughness could be affected by cutting conditions, supply and cooling methods. The experimental results show that MQL technology is able to minimize harmful effects of conventional cutting fluids.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.980-986
• /
• 2003

As the ultra precision grinding can be applied to wafering process by the refinement of the abrasive, the development of high stiffness equipment and grinding skill, the conventional wafering process which consists of lapping, etching, Ist, 2nd and 3rd polishing could be exchanged to the new process which consists of precision surface grinding, final polishing and post cleaning. Especially, the ultra precision grinding of wafer improves the flatness of wafer and the efficiency of production. Futhermore, it has been not only used in bare wafer grinding, but also applied to wafer back grinding and SOI wafer grinding. This paper focused on the effect of the wheel path density and relative velocity on the characteristic of ground wafer in in-feed grinding with cup-wheel. It seems that the variation of the parameters in radial direction of wafer results in the non-uniform surface quality over the wafer. So, in this paper, the geometric analysis on grinding process is carried out, and then, the effect of the parameters on wafer surface quality is evaluated

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.1
• /
• pp.13-19
• /
• 2012

In this study, ultrasonic vibration tool designed and made by using FEM analysis. And machining test was carried out in various machining conditions using ultrasonic vibration capable CNC machine. For work material, alumina ceramic ($Al_2O_3$) was used while for tool material diamond electroplated grinding wheel was used. To evaluate ultrasonic vibration effect, grinding test was performed with and without ultrasonic vibration in same machining condition. In ultrasonic mode, ultrasonic vibration of 20kHz was generated by HSK 63 ultrasonic actuator. The two grinding speeds, 1.67m/s and 3.35m/s, were applied. On the other hand, grinding forces were measured by KISTLER dynamometer.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.918-921
• /
• 2001

In grinding process, the heat of $1200^{\circ}$~$1500^{\circ}$ on the grinding area between grinding wheel and workpiece is generated. It decreases the surface integrity of workpiece and causes the thermal damages such as the deformed layer, residual stress and grinding burn. Generally coolant is widely used for preventing the heat generation on the grinding area, but it deteriorates the working condition by polluting the atmosphere of workplace and in the end pollutes the environment. The grinding methods using the compressed cold air and mist are the cooling methods to substitute conventional coolant. They can decrease the environmental pollution through not using coolant any more or minimizing it. In this study, the cooling effects of grinding methods using the compressed cold air and mist have been investigated. The grinding system equipped with the water bathe and mist spray nozzle was developed. The energy partition to workpiece through measuring the temperature on the workpiece surface was calculated. The surface integrity of workpiece and thermal damage like the deformed layer were analyzed.