• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.1
• /
• pp.83-94
• /
• 1999

본 연구에서는 시스템의 해석적 모델과 측정된 응답을 이용하여 입력하중을 추정하는 역해석 기법을 유한요소모델과 같은 해석적 모델을 알고 있는 경우와 주파수응답함수와 같은 실험적 모델을 알고 있는 경우에 대하여 제시하였으며 이때 발생되는 수학적 악조건의 특성을 규명하였다. 역해석시 발생되는 수학적 악조건은 시스템의 동강성행렬과 측정위치에 의해 결정되는 특성행렬의 조건수에 따라 결정되며 역해석기법을 공학문제에 적용하기 위하여는 특성행렬의 조건수가 낮아지도록 주자유도 및 측정점을 선택하여야 하고 특히 공진영역 및 반공진영역에서는 필연적으로 악조건이 발생됨을 알 수 있었다. 수학적 악조건의 특성을 명확히 규명하기 위하여 간단한 수치해석을 통하여 그 결과를 제시하였다.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.6
• /
• pp.43-50
• /
• 2002

In the design of structure, the forces acting on tai structure are key parameter fur noise and vibration control. However, in the complex structure, the forces at the injection point on the structure cannot be measured directly. So, it is necessary to find out Indirect force evaluation method. In this paper, forces have been measured with In-situ vibration responses and system information. And, three existing techniques of indirect force measurement, vita. direct inverse. principal component analysis and regularization have been compared. This paper shows that multi-vibration responses are essential for talc precise estimation of the forces. To check these conditions, rotary compressor is adopted as test sample, because it is very difficult to measure the injection forces from internal excitation to shell. It alas also been obtained that relatively higher force is transmitted through three welding paths to the compressor shell. It shows a good agreement between direct and indirect force evaluation with curvature shell and plate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.564-567
• /
• 1997

In the design of structure the forces acting on the structure are important parameter for noise and vibration control. However, in the complex structure, the forces at the injection point on the structure cannot be measured directly. Thus it is necessary to find out indirect force evaluation method. In this paper forces have been measured with in-situ vibration responses and system information. Three existing techniques of indirect force measurement, viz. direct inverse, principal component analysis and regularization have been compared. It has been shown that multi-vibration responses are essential for the precise estimation of the forces. To satisfy those conditions, Rotary compressor is adopted as test sample, because it is very difficult to measure the injection forces from internal excitation to shell. It has also been obtained that relatively higher force is transmitted though three welding paths to the compressor shell. It shows a good agreement between direct and indirect force evaluation with curvature shell and plate and is investigated the possibility of force evaluation of rotary compressor as a complex structure.

• Computational Structural Engineering
• /
• v.6 no.2
• /
• pp.95-102
• /
• 1993

A modeling method is described to provide a smaller structural dynamic model which can be used to compare finite element model of a structure with its experimental counterpart. A structural dynamic model is assumed to be represented by dynamic stiffness matrix. To validate a finite element model, it is often necessary to condense a large degrees of freedom (dofs) to a relatively small number of dofs. For these purpose, static reduction techniques are widely used. However, errors in these techniques are caused by neglecting frequency dependent terms in the functions relating slave dofs and master dofs. An alternative method is proposed in this paper in which the frequency dependent terms are considered by expressing the reduced dynamic stiffness matrix with orthogonal polynomials. The reduced model has finally a minimum set of dofs, such as sensors and excitation points and it is under the same condition as the physical system. It is proposed that the reduced model can be derived from finite element model. The procedure is applied to example structure and the results are discussed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.13 no.1
• /
• pp.47-54
• /
• 1993

For the numerical analysis of free oscillation characteristics in a harbor with general boundary and bottom topography, finite element method is applied. The governing Helmholtz equation is transformed into a generalized matrix eigenvalue problem using the standard finite element procedure. A computer code is developed for the numerical evaluation of natural frequencies and free oscillation modes. In the eigensolution process, a shifting strategy is devised for the treatment of numerical singularity. Scaling of coefficient matrix is also found to be effective for the alleviation of numerical ill-conditioning. For the test problems, firstly, analytical and numerical solutions are compared and validity of the code is obtained. Hence the method is successfully applicable for the real-world problems with general geometric boundaries and bottom topography.

• Geophysics and Geophysical Exploration
• /
• v.7 no.3
• /
• pp.207-212
• /
• 2004

This article reviews recent developments in three-dimensional (3-D) magntotelluric (MT) imaging. The inversion of MT data is fundamentally ill-posed, and therefore the resultant solution is non-unique. A regularizing scheme must be involved to reduce the non-uniqueness while retaining certain a priori information in the solution. The standard approach to nonlinear inversion in geophysis has been the Gauss-Newton method, which solves a sequence of linearized inverse problems. When running to convergence, the algorithm minimizes an objective function over the space of models and in the sense produces an optimal solution of the inverse problem. The general usefulness of iterative, linearized inversion algorithms, however is greatly limited in 3-D MT applications by the requirement of computing the Jacobian(partial derivative, sensitivity) matrix of the forward problem. The difficulty may be relaxed using conjugate gradients(CG) methods. A linear CG technique is used to solve each step of Gauss-Newton iterations incompletely, while the method of nonlinear CG is applied directly to the minimization of the objective function. These CG techniques replace computation of jacobian matrix and solution of a large linear system with computations equivalent to only three forward problems per inversion iteration. Consequently, the algorithms are efficient in computational speed and memory requirement, making 3-D inversion feasible.