• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.4
• /
• pp.527-535
• /
• 2019

Hanger in a rail-launched missile protrudes in general and causes to increase significant drag force. One method to avoid the significant increase of drag force is to apply fairings on the hanger. In this paper, sloping shaped fairing parameters of height, width, and length are optimized to minimize the drag force under subsonic speed region by examining three configurations of fairings : front-fairing only, rear-faring only, and the both front and rear fairing. We use Latin Hypercube Sampling method to determine the experimental points, and computational fluid dynamics with incompressible RANS solver was applied to acquire the data at sampling points. Then, we construct a meta model by kriging method. We find the best choice among three configurations examined : both front and rear fairing reduce the drag force by 63 % without the constraint of fairing mass, and front fairing reduced the drag force by 52 % with the constraint of hanger mass.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.26 no.2
• /
• pp.25-30
• /
• 2024

This study was conducted to develop the hanging type circular-patterned system that at maximizing the spatial efficiency of strawberry cultivation to increase yields, while also reducing labor and improving energy efficiency. The system consists of a cultivation bed units, longitudinal moving device, bed lifting device, front and rear transfer devices, lateral transfer device, nutrient supply device, and control unit. Performance testing revealed that the operational motor for longitudinal movement should have a torque of at least 0.1Nm based on the design weight and traction force of the cultivation bed unit. The power consumption required to move one cycle was calculated to be approximately 149Wh when performing harvesting or maintenance tasks for all 10 cultivation beds. Vibration angles measured during bed movement showed that the lateral transfer resulted in a roll angle ranging from -0.62° to 0.68° and a pitch angle ranging from -3.79° to 5.26°. For longitudinal transfer, the roll angle ranged from -3.37° to 3.36°, and the pitch angle ranged from -0.45° to 0.49°.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.38 no.1
• /
• pp.37-44
• /
• 2014

For testing a two-wheeled vehicle's per-charge range, this study conducted road and chassis dynamometer driving tests. Three typical road routes within Daejeon Metropolitan City were selected for the road-driving test. In the case of CVS-40 mode driving tests using a chassis dynamometer, various road-loading conditions were set. In this study, two-wheeled electric vehicles' per charge range on the road was confirmed through testing, and the range and energy consumption efficiency depending on various chassis dynamometer road load settings were measured. Then, the results of the actual road driving tests were compared with those of the chassis dynamometer driving tests, and road load settings that yielded per-charge range testing results similar to those under actual road driving conditions in the chassis dynamometer experiments were studied.

• Industry Promotion Research
• /
• v.4 no.1
• /
• pp.1-9
• /
• 2019

This study is a technology related to a seismic protection device for a fire pipe for installation in a building such as an apartment or a building. The fire pipe is fixed to the base panel by fastening bolts so as to flow left and right. The present invention relates to an earthquake-resistant apparatus for a fire-extinguishing piping, which is capable of minimizing damages caused by an earthquake in order to prevent damages and breakage of a fire-extinguishing pipe by mitigating earthquakes, vibrations, It is connected to an insert plate embedded in concrete or ceiling hanger bolts formed at regular intervals on the ceiling to keep the piping constant from the ceiling and to keep the horizontal condition of the piping always constant so that the piping relaxes or sags And to effectively prevent damage to the piping. The can get.

• Journal of the Korea Safety Management & Science
• /
• v.21 no.4
• /
• pp.75-80
• /
• 2019

Sales of the Korean clothing industry grew to 16.9 percent on-year in 2010, but the growth rate dropped to 3 percent from 2011 to 2016 and the overall market began to slump to 1.1.6 percent in 2017. The competitiveness of clothing companies is also a major sector in logistics capability, and the average logistics cost of domestic clothing companies is 8.3 percent of sales in 2011, higher than the average 8 percent of domestic industries, and 36.4 percent of the total storage cost in 2011, higher than the 28.8 percent share of the total storage cost of domestic companies. As domestic production conditions such as wage hikes and labor disputes worsened in the 1990s, production facilities were rapidly moved overseas, which led many clothing companies to have no production facilities or a minimal production base in Korea and focus on marketing and design capabilities. The total storage capacity and storage efficiency of the logistics center became very important as the products were changed to the form of mass warehousing and small-volume forwarding. Research shows that building column spacing, a model of this research, can affect the amount of hanger rack storage empirically, so for sustainable growth of clothing companies, it is necessary to improve competitiveness in the logistics market by reducing costs and improving efficiency to overcome difficulties in corporate management. Because logistics costs are 8.3 percent and operating profit to sales ratio is 2 percent, it is expected that operating profit will increase by 41.5 percent if logistics costs are reduced by 10 percent. If 10% of storage cost is saved based on storage cost, operating profit is expected to increase by 15% To strengthen the competitiveness of the clothing industry, a reduction in logistics costs is essential. Therefore, the purpose of this study is to provide hints that logistics experts can have empirically small amounts in reducing storage costs through column spacing adjustment of logistics centers that have not been dealt with statistically until now, and to contribute to the continued growth of clothing companies and the development of the domestic logistics industry.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.6
• /
• pp.166-174
• /
• 2011

The object of this study is to evaluate the structural shear capacity of the PC girder-PC beam joint. The dapped end of PC beam and the ledger of PC girder are usually designed to design load. If the end of PC beam can be designed with continuous end, the dapped end of PC beam and the ledger of PC girder do not need to resist to all loads except dead load and construction load. The experimental program was carried out with 7 specimens containing the variable factors as the anchored method of the hanger bar, design load, be or not exist of ledger bars. As a result, the continuity of the dapped end and the ledger were ensured their safety although the design load was only the dead load and the construction load. The shear critical section was expanded toward the effective depth d, the distance from the supported position of the beam. If the ledger is designed according to PCI Design Handbook, the structural system of the ledger is as to the cantilever slab system. But the ledger of this study is as to the 3 side fixed slab system. Therefore the design of the ledger by PCI Design Handbook will lead to highly conservative results.