• Tunnel and Underground Space
• /
• v.34 no.1
• /
• pp.54-70
• /
• 2024

Utilization of completed open-pit for mining waste disposal is an alternative method of tailing storage facility (TSF), which can minimize the area and cost required for the installation of TSF. However, long-term tailing disposal into open-pit has a potential risk of reducing mechanical stability of surrounding rock mass by acting as an additional load. In this research, a realistic open-pit tailing disposal scenario of 60,400 hours was established based on the case of Marymia gold mine, Australia. Mechanical stability of surface pillar between open-pit and underground stope was analyzed numerically by using Sigma/W, under different stope geometry and rock mass conditions. Simulation results showed that long-term tailing disposal into open-pit can significantly increase the failure probability of surface piller. This result suggests that mechanical stability of mine geometry should be conducted beforehand of open-pit tailing disposal.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.44 no.9
• /
• pp.1339-1346
• /
• 2015

In a previous study, baekseolgi with xylitol or sucralose was comparable to baekseolgi with sugar in terms of all sensory characteristics. However, the hardness of sucralose baekseolgi increased considerably during storage while that of xylitol baekseolgi remained unchanged. To improve the physical limitations observed in sucralose baekseolgi, a combination of sucralose and xylitol were substituted for sugar when preparing baekseolgi (SL0~SL100, SLn; baekseolgi where sugar was replaced with n% sucralose and 100-n% xylitol based on relative sweetness to sugar). All SLn baekseolgi samples were not significantly different from sugar baekseolgi in terms of sensory properties. The moisture content was not different between sugar and xylitol baekseolgi (SL0), but decreased significantly as the amount of sucralose increased (P<0.01), which correlated with cohesiveness of baekseolgi. Texture profile analysis revealed that hardness of SLn baekseolgi increased without any noticeable change in moisture content after storage at $4^{\circ}C$ for 7 days. In addition, the hardness after storage was the highest in sucralose baekseolgi (SL100), which was comparatively lower in SL0~SL80 containing xylitol presumably due to the hygroscopic characteristics of xylitol. In particular, SL20 was found to be comparable to sugar baekseolgi in terms of moisture and cohesiveness during storage. The results showed that the combination of xylitol and sucralose could be a potential sugar substitute in terms of not only sensory characteristics but also physicochemical properties.

• Economic and Environmental Geology
• /
• v.38 no.6 s.175
• /
• pp.717-729
• /
• 2005

Peak cooling load of large buildings is generally greater than their peak heating load. Internal and solar heat gains are used fur selection of adquate equipment in large building in cold winter climate like Canada and even Korea. The cost of geothermal heat exchanger to meet the cooling loads can increase the initial cost of ground source heat pump system to the extend less costly conventional system often chosen. Thermal ice storage system has been used for many years in Korea to reduce chiller capacity and shift Peak electrical time and demand. A distribution system designed to take advantage of heat extracted from the ice, and use of geothermal loop (geothermal heat exchanger) to heat as an alternate heat source and sink is well known to provide many benifits. The use of thermal energy storage (TES) reduces the heat pump capacity and peak cooling load needed in large building by as much as 40 to $60\%$ with less mechanical equipment and less space for mechanical room. Additionally TES can reduce the size and cost of the geothermal loop by 1/3 to 1/4 compared to ground coupled heat pump system that is designed to meet the peak heating and cooling load and also can eliminate difficuties of geothermal loop installation such as space requirements and thermal conditions of soil and rock at the urban area.

• The Korean Society of Law and Medicine
• /
• v.16 no.2
• /
• pp.87-130
• /
• 2015

In a case in which National Health Insurance Corporation (NHIC) pays medical care expenses to a victim of a traffic accident resulting in injury or death and asks the assailant for compensation of its share in the medical care expenses, as the precedent treats the subrogation of a claim set by National Health Insurance Act the same as that set by Industrial Accident Compensation Insurance Act, it draws the range of its compensation from the range of deduction, according to the principle of deduction after offsetting and acknowledges the compensation of all medical care expenses borne by the NHIC, within the amount of compensation claimed by the victim. However, both the National Health Insurance Act and the Industrial Accident Compensation Insurance Act are laws that regulate social insurance, but medical care expenses in the National Health Insurance Act have a character of 'an underinsurance that fixes the ratio of indemnification,' while insurance benefit on the Industrial Accident Compensation Insurance Act has a character of full insurance, or focuses on helping the insured that suffered an industrial accident lead a life, approximate to that in the past, regardless of the amount of damages according to its character of social insurance. Therefore, there is no reason to treat the subrogation of a claim on the National Health Insurance Act the same as that on the Industrial Accident Compensation Insurance Act. Since the insured loses the right of claim acquired by the insurer by subrogation in return for receiving a receipt, there is no benefit from receiving insurance in the range. Thus, in a suit in which the insured seeks compensation for damages from the assailant, there is no room for the application of the legal principle of offset of profits and losses, and the range of subrogation of a claim or the amount of deduction from compensation should be decided by the contract between the persons directly involved or a related law. Therefore, it is not reasonable that the precedent draws the range of the NHIC's compensation from the principle of deduction after offsetting. To interpret Clause 1, Article 58 of the National Health Insurance Act that sets the range of the NHIC's compensation uniformly and systematically in combination with Clause 2 of the same article that sets the range of exemption, if the compensation is made first, it is reasonable to fix the range of the NHIC's compensation by multiplying the medical care expenses paid by the ratio of the assailant's liability. This is contrasted with the range of the Korea Labor Welfare Corporation's compensation which covers the total amount of the claim of the insured within the insurance benefit paid in the interpretation of Clauses 1 and 2, Article 87 of the Industrial Accident Compensation Insurance Act. In the meantime, there are doubts about why the profit should be deducted from the amount of compensation claimed, though it is enough for the principle of deduction after offsetting that the precedent took as the premise in judging the range of the NHIC's compensation to deduct the profit made by the victim from the amount of damages, so as to achieve the goal of not attributing profit more than the amount of damage to a victim; whether it is reasonable to attribute all the profit made by the victim to the assailant, while the damages suffered by the victim are distributed fairly; and whether there is concrete validity in actual cases. Therefore, the legal principle of the precedent concerning the range of the NHIC's compensation and the legal principle of the precedent following the principle of deduction after offsetting should be reconsidered.

• Korea Science and Art Forum
• /
• v.20
• /
• pp.147-158
• /
• 2015

This study made an approach to the industrial exhibition space, which is a medium of marketing communication, from the position of an enterprise and consumers through the output of Space Design, and conducted it with focus on B2B transactions among specialized exhibitions. In addition, this study inquired into what factors should be considered along with space design by interpreting the purpose of participating in the exhibition and space design of the enterprise which supply capital goods, elements, related technologies and materials, etc. This study aimed at drawing the direct/indirect effect, produced by space design, on the marketing by analyzing correlation between space design and participating enterprises' marketing. Despite the marketing effect of the exhibition, which was proved by preceding research results, the reality is that exhibition-participating expenses work as considerable burden on enterprises. Particularly, booth design, which is forming the most proportion among the participating expenses, was found to have insufficient influence on visitors due to the decline in its importance among diverse factors influencing visitor's decision to visit a booth. Regardless of the business category of participating enterprises in the exhibition, the standard of exhibits was ranked as the most important consideration factor in visiting a booth. Even by business category, the standard of booth design rarely had an influence on booth visit. Booth design had an affirmative influence on participating enterprise's preference, but its influence on product purchase or business talk & contact with a participating enterprise or price was found to be extremely low. It's difficult to judge marketing success or failure of an exhibition by the form and standard of booth design. Preferably, this study infers that it's necessary to put much weight on qualitative excellence of an exhibition, which consists of participation of an enterprise in possession of excellent technologies, exhibits with higher standards and high-quality visitors with purchasing power. This study suggests that it's more effective to set up the plan for expansion of participation in exhibition by optimally regulating the proportion of space design in participating expense to increase marketing effectiveness of an exhibition. The limitations of this study, analysis of which based on the visitors to an exhibition only, requires supplementation through the follow-up research work on participating enterprises in the exhibition.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.157-164
• /
• 2016

In this study, researchers performed preliminary design and numerical analysis for a pilot-scale helium heating system intended to support full-scale construction for a sulfur-iodine (SI) cycle. The helium heat exchanger used a liquefied petroleum gas (LPG) combustor. Exhaust gas velocity at the heat exchanger outlet was approximately 40 m/s based on computational thermal and flow analysis. The maximum gas temperature was reached with six baffles in the design; lower gas temperatures were observed with four baffles. The amount of heat transfer was also higher with six baffles. Installation of additional baffles may reduce fuel costs because of the reduced LPG exhausted to the heat exchanger. However, additional baffles may also increase the pressure difference between the exchanger's inlet and outlet. Therefore, it is important to find the optimum number of baffles. Structural analysis, followed by thermal and flow analysis, indicated a 3.86 mm thermal expansion at the middle of the shell and tube type heat exchanger when both ends were supported. Structural analysis conditions included a helium flow rate of 3.729 mol/s and a helium outlet temperature of $910^{\circ}C$. An exhaust gas temperature of $1300^{\circ}C$ and an exhaust gas rate of 52 g/s were confirmed to achieve the helium outlet temperature of $910^{\circ}C$ with an exchanger inlet temperature of $135^{\circ}C$ in an LPG-fueled helium heating system.

• Journal of the Korean earth science society
• /
• v.28 no.1
• /
• pp.64-74
• /
• 2007

The marine seismic prospecting using a research vessel in the shallow sea near the coastal area has certain limits according to the water depth and survey environment. Also, for the electrical resistivity survey at seashore area, one may need a specially designed high-voltage source to penetrate the very conductive surface layer. Therefore, we have conducted a feasibility study on the application of magnetotelluric method (MT), a passive geophysical method, on investigating of shallow marine environment geology. Our study involves both theoretical modeling and field survey at the tidal flat area which represent the very shallow marine environment. We have applied the audio-frequency magnetotelluric (AMT) method to the intertidal deposits of Gunhung Bay, west coast of Korea, and analysed the field data both qualitatively and quantitatively to investigate the morphology and sedimentary stratigraphy of the tidal flat. The inversion of AMT data well reveals the upper sedimentary layer of Holocene intertidal sediments having a range of 13-20 m thickness and the erosional patterns at the unconformable contact boundary. However, the AMT inversion results tend to overestimate the depth of basement (30-50 m) when compared with the seismic section (27-33 m). Since MT responses are not significantly sensitive to the resistivity of middle layer or the depth of basement, the AMT inversion result for basement may have to be adjusted using the comparison with other geophysical information like seismic section or logging data if possible. But, the AMT method can be an effective alternative choice for investigating the seashore area to get important basic informations such as the depositional environment of the tidal flat, sea-water intrusion and the basement structure near the sea shore.

• KIPS Transactions on Computer and Communication Systems
• /
• v.10 no.10
• /
• pp.261-268
• /
• 2021

Cloud computing is a computing paradigm in which users can utilize computing resources in a pay-as-you-go manner. In a cloud system, resources can be dynamically scaled up and down to the user's on-demand so that the total cost of ownership can be reduced. The Modeling and Simulation (M&S) technology is a renowned simulation-based method to obtain engineering analysis and results through CAE software without actual experimental action. In general, M&S technology is utilized in Finite Element Analysis (FEA), Computational Fluid Dynamics (CFD), Multibody dynamics (MBD), and optimization fields. The work procedure through M&S is divided into pre-processing, analysis, and post-processing steps. The pre/post-processing are GPU-intensive job that consists of 3D modeling jobs via CAE software, whereas analysis is CPU or GPU intensive. Because a general-purpose desktop needs plenty of time to analyze complicated 3D models, CAE software requires a high-end CPU and GPU-based workstation that can work fluently. In other words, for executing M&S, it is absolutely required to utilize high-performance computing resources. To mitigate the cost issue from equipping such tremendous computing resources, we propose HEMOS-Cloud service, an integrated cloud and cluster computing environment. The HEMOS-Cloud service provides CAE software and computing resources to users who want to experience M&S in business sectors or academics. In this paper, the economic ripple effect of HEMOS-Cloud service was analyzed by using industry-related analysis. The estimated results of using the experts-guided coefficients are the production inducement effect of KRW 7.4 billion, the value-added effect of KRW 4.1 billion, and the employment-inducing effect of 50 persons per KRW 1 billion.

• Clinical and Experimental Pediatrics
• /
• v.48 no.10
• /
• pp.1068-1075
• /
• 2005

Purpose : The role of ghrelin, which promotes the secretion of growth hormone, was not well known until now. Recently it was found that the mutation of ghrelin gene is related to obesity and diabetes. This study is to find the screening method that can easily and effectively detect the polymorphism of Leu72Met in ghrelin gene of obesity patients and apply it to clinical usage. Methods : We compared PCR-RFLP, PCR-SSCP and ARMS methodologies for analyzing of the polymorphism of Leu72Met in ghrelin gene of obesity children, and also studied the merits and demerits of these methodologies. Results : In this study, we were able to find out the band of peculiar allele of Leu72Met in ghrelin gene using PCR-RFLP, PCR-SSCP and ARMS analyses. The polymorphism of Leu72Met in ghrelin gene determined by all above methodologies was in complete agreement. Compared to the PCR-RFLP and PCR-SSCP, ARMS analysis is simple, inexpensive and also consume less time. It is very sensitive to analyze the polymorphism and easy to understand the results of test. Conclusion : Though PCR-RFLP, PCR-SSCP and ARMS analyses were sensitive to analyze the polymorphism of Leu72Met in ghrelin gene, ARMS analysis appears to be more efficient than PCR-RFLP and PCR-SSCP. Therefore, we conclude that ARMS analysis is suitable to analyze the polymorphism of Leu72Met in ghrelin gene for large quantity of specimens.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.6
• /
• pp.517-534
• /
• 2021

Hydrogen fuel is emerging as an new energy source to replace fossil fuels in that it can solve environmental pollution problems and reduce energy imbalance and cost. Since hydrogen is eco-friendly but highly explosive, there is a high concern about fire and explosion accidents of hydrogen fueled vehicles. In particular, in semi-enclosed spaces such as tunnels, the risk is predicted to increase. Therefore, this study was conducted on the applicability of the equivalent TNT model and the numerical analysis method to evaluate the hydrogen explosion pressure in the tunnel. In comparison and review of the explosion pressure of 6 equivalent TNT models and Weyandt's experimental results, the Henrych equation was found to be the closest with a deviation of 13.6%. As a result of examining the effect of hydrogen tank capacity (52, 72, 156 L) and tunnel cross-section (40.5, 54, 72, 95 m²) on the explosion pressure using numerical analysis, the explosion pressure wave in the tunnel initially it propagates in a hemispherical shape as in open space. Furthermore, when it passes the certain distance it is transformed a plane wave and propagates at a very gradual decay rate. The Henrych equation agrees well with the numerical analysis results in the section where the explosion pressure is rapidly decreasing, but it is significantly underestimated after the explosion pressure wave is transformed into a plane wave. In case of same hydrogen tank capacity, an explosion pressure decreases as the tunnel cross-sectional area increases, and in case of the same cross-sectional area, the explosion pressure increases by about 2.5 times if the hydrogen tank capacity increases from 52 L to 156 L. As a result of the evaluation of the limiting distance affecting the human body, when a 52 L hydrogen tank explodes, the limiting distance to death was estimated to be about 3 m, and the limiting distance to serious injury was estimated to be 28.5~35.8 m.