• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.2
• /
• pp.98-106
• /
• 2019

Human-powered aircraft has wings with a shape of high aspect ratio which results in large bending displacement. This paper aims to improve the structural limitation by changing an incidence angle of the wings. The tendency change of bending displacement at the wing tip is observed assuming that airfoil and cross-sectional shape of the wing is fixed, and amount of the total lift generated is satisfied. Quasi-steady lift, drag and the aerodynamic moment are distributed with regard to sections of the wing. Those are analyzed using a numerical nonlinear lifting-line method and 'geometrically exact beam' (GEB) program in EDISON. 'Variational Asymptotic Beam Sectional Analysis' (VABS) program is used to check if the present wing is structurally solid. Furthermore, the predicted tip deflections are verified by comparing with DYMORE.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.6
• /
• pp.564-569
• /
• 2010

VOR/DME is the short range radio navigation system for much of the world. The navigation with VOR/DME is used for a long time because of its reliability. It can be used for almost all civil aircraft. To simulate the small aircraft's autopilot system based on VOR/DME system, we developed a simulator by using SIMULINK. The output panel of the simulator was developed according to the cockpit instrument of an actual aircraft. To verify the performance of the simulator several scenarios were planned. And we showed that the simulator performed well.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.11
• /
• pp.33-40
• /
• 2005

The reliability of flight control system(FCS) for Unmanned Air Vehicle(UAV) is underestimated because of the design restrictions such as small size, low cost and light weight. However because the failure of FCS may cause the loss of aircraft, the reliability of FCS must be analysed and validated whether it meet the reliability requirements in design phase.In this paper the failure rate of subsystems was divided with its function based on the design experience of FCS. The redundancy models which satisfy the system reliability requirements were suggested. These results may be utilized in the hardware design of FCS.

• Aerospace Engineering and Technology
• /
• v.8 no.2
• /
• pp.149-159
• /
• 2009

This paper deals with an analytical study on the aileron reversal characteristics of anisotropic composite aircraft wings modelled as thin-walled beam and having extension-twist structural couplings caused by Circumferentially Uniform Stiffness (CUS) layup scheme. For a study on the aileron reversal of CUS composite wings, it is essential to consider the following effects such as extension-twist structural coupling, wing aspect ratio, and ratio of span-wise and chord-wise length of aileron to wing, initial angle of attack, and sweep angle, etc. The results on the aileron reversal could have a significant role in more efficient designs of thin-walled composite wing aircraft for which this aeroelastic instability is one of the most critical ones.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.4
• /
• pp.17-24
• /
• 2006

Hydrodynamic ram of aircraft fuel tanks is one of main ballistic battle damages of an aircraft and has great importance to airframe survivability design. Basic concept, physics and research history of hydrodynamic ram are investigated. The penetration and internal detonation of a simple fuel tank and ICW(Intermediate Complexity Wing) are analyzed by computational method. Structural rupture and fluid burst are analytically realized using general coupling and coupling surface interaction. The results such as fluid pressure, tank stress and displacement are shown and future research chances are suggested based on the study.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.1
• /
• pp.20-27
• /
• 2002

Aircraft design requires the intergration of several disciplines, inculding aerodynamics, structures, controls. To achieves advances in performance, each technology, or discipline must be more accurate in analysis and must be more highly intergrated. One of the important interdisciplinary interactions in mordern aircraft design is that of aerodynamics and structures. In this study, for increasing accuracy in each discipline's analysis, CFD for aerodynamic analysis and FEM for structurral analysis was used and, for considering important interdisciplinary interactions, aeroelastic effect was considered. As optimization algorithm, PBIL algorithm was used for global optima and was parallelized to alleviate the computational burden. The efficiency and accuracy of the present method was assesed by range maximiziation of reference of reference wing.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.240-247
• /
• 2006

Tilt rotor aircraft is a multi-configuration airplane which has three independent flight modes; helicopter, conversion, and aiplane. The control surface mixer resign is reqctired to generate and distribute efficient control forces and moments in each flight mode. In the conversion mode, the thrust vector is changed from helicopter mode to airplane, therefore the thrust vector makes undesired forces and moments which affect on pitch, roll and yaw dynamics. This paper describes the design results of control surface mixer design which minimize the undesired forces and moments due to nacelles tilting angle change for 4O% scaled model.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.37-46
• /
• 2006

The outside environment is very severe while aircraft is cruising. Especially small particle of icing in cold air condition can have negative influence on aircraft performance. If ice particle is attached to leading edge of wing, it can change wing configuration and decrease flight quality. If icing particle is attached to inlet of engine, it can damage compressor blade and have negative influence to aircraft safety. We make icing simulation device with liquid air system for analyzing about variation of engine performance due to incoming of icing to engine.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.46-46
• /
• 2008

스텔스 기능을 가진 군사용 항공기는 레이다 망의 추적을 피하기 위해 일반 냉각수 대신에 절연유를 냉각매체로 사용한다. 그러나 절연유는 물에 비하여 열전달특성이 매우 낮기 때문에 항공기 전기전자 기기/부품 발열부를 효과적으로 냉각시키지 못하는 한계성을 가지고 있다. 따라서 본 연구에서는 나노유체(Nanofluid) 개념을 이용하여 절연유에 알루미나 및 질화알루미늄 나노분말을 미랑 분산시킨 나노절연유를 제조하고 이것의 열전달특성을 순수 절연유의 그것과 비교 평가함으로써, 냉각특성이 크게 개선된 새로운 냉매로서의 적용 가능성을 확인하고자 하였다. 다만 나노절연유를 제조함에 있어서 가장 큰 장애물은 오일에 대한 분산성 확보에 있기 때문에, 비드밀 및 초음파를 이용한 나노분말 응집체의 습식분산 및 분산제를 이용한 친유성 표면개질을 동시에 수행함으로써 장시간 안정된 분산성을 확보하도록 노력하였다. 나노유체의 열전도도 및 대류열전달계수는 비정상열선법을 이용하여 측정하였으며, 유체 속의 분말 분산 상태는 원심력을 이용한 분산안정성 평가장치 및 cryo FE-SEM을 이용하여 확인하였다. 또한 분말 형상이 대류열전달에 미치는 영향을 조사하기 위하여 알루미나 나노분말은 구상과 침상의 분말을 모두 사용하였고, 질화알루미늄 외에 다이아몬드 나노절연유도 함께 제조, 평가함으로써 냉각 및 절연특성, 그리고 물리화학적 안정성이 우수하고 실적용 가능성이 가장 높은 재료를 도출하고자 하였다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.1-9
• /
• 2004

The performance analysis code has been developed for vertical take-off and landing(VTOL) UAV which can be utilized as a trade analysis tool in the pre-conceptual design phase. The UAV requires VTOL capability and high speed cruise performance. The main logic of this performance analysis code is to estimate performance parameters of each mission segment by mission fuel weight iteration. The reliability of this performance analysis code is discussed by comparing the data of existing dual flight mode VTOL UAVs such as Boeing CRW and Bell Tilt Rotor.