• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.157-164
• /
• 2000

This study is about predicting the interior pressure level of the korean high speed train using ray acoustic method. The motor car and the motor and passenger cabin are investigated under the environment of passing open countryside and inside tunnel of 350 km/hr. Calculated sound levels are compared with the proposed sound levels and suggestions about the transmission Joss values of isolating panels inside motor car and the guide lines of allowed sound power limit of motor equipments are provided. Results of TPI car show calculated interior sound level is below the proposed values for both cases of open countryside running and inside tunnel. Since ray acoustic method calculated only air borne noise component, real sound level of the motor car may be higher than prediction. Passenger cabins of TMI, TM5 show higher sound level than the proposed values, so window method was carried out to find the contribution of each panel components and point out the remedy of transmission path. Reduction of sound power of motor equipments should be condisered at the same time.

• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.235-242
• /
• 2000

The most important technology to improve crashworthiness of high speed trains is to design their front structures to absorb crash energy easily. In this paper, crashworthy designs of the front structures in KTX and KHST are compared by numerical simulation under SNCF accident scenario. Furthermore, to evaluate their crashworthiness tinder a typical real situation, the power cars are simulated for the accident collided against a deformable dump truck of 15 tons at 110 kph. The front structure of KHST, finally designed, shows a good crashworthy characteristics. Finally, the impact strength of coupling components is evaluated by analyzing a consist of the front three KHST units under scenario of train-to-train collision at 30 kph.

• Proceedings of the KSR Conference
• /
• 2003.10a
• /
• pp.156-161
• /
• 2003

Korean High Speed Train (KHST) has been tested on high speed line in JungBu site since it was developed in 2002. The data acquisition system was used to test successfully the on-line test for proving the dynamic performance of KHST. The recognition of system vibration mode for railway vehicle is essential to understand the characteristics of design for dynamic system and diagnose the dynamic problems of vehicle system during test and operation. But, up to now, there are the efforts to know the system vibration mode within limit of theoretical field only, not experimental approach with systematic method. The theoretical results are too reliable to apply to real design problem, because it is theoretically based on the homogeneous linear system although the real system have the nonlinear characteristics and vary the environmental conditions. Therefor, in this paper, it is proposed the efficient method of vibration analysis for rail vehicle system and this method apply to KHST to recognize the vibration mode characteristics of it. The results show that this method is able to make the system vibration modes for KHST clear.

• Proceedings of the KSR Conference
• /
• 2003.10a
• /
• pp.181-186
• /
• 2003

In order to develop a high speed train, various conditions have been considered. Fatigue strength assessment by the fluctuation of pressure is an important one. In this study, a numerical simulation has been performed to estimate the fluctuation and frequency of pressure when KHST(Korean High Speed Train)passes through tunnels in the Kyung-Bu high-speed railway. The simulation was based on KHST running the Kyung-Bu high-speed line with the speed of 350km/h and the interval of 10 minute headway. And the tunnel entrance speed was estimated by TPS program. Therefore, the fluctuation and frequency of pressure is expressed in Weibull distribution function in the above running situation. The result in this study would be good guidance to calculate the fatigue life and the index of reliability of body structure. We are going to conduct more study to measure the real value of the pressure of the carbody passing through tunnels, to assess the fatigue reliability and to develop method ＆ procedure for the fatigue reliability design.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.218-221
• /
• 2004

This Research is to test the running stability of the developed bogie with 350km/h of which conventional speed is faster than Korea TGV 300Km/h. The running stability test has been executed in status of a car with the developed bogie on the roller rigger to adjust similar to the actual condition. And the test has been done in the two rail conditions, i.e. excitation and non-excitation, respectively. Running speed of bogie increased by the roller step by step. In consequence, the developed bogie in the non-excitation has run without any unstable point for 400kn0h. Vibration characteristics of carbody also was within the value specified on the UIC 518.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.200-205
• /
• 2004

The pantograph for Korean High Speed Train was developed and had been evaluating by through 'G7-R&D project for home grown high speed train technology' In this study, in mechanical aspect, the variation trend of contact force between pantograph and catenary according to the train running speed and driving pattern is conducted. A measuring system for current collecting performance and mechanical characteristics is used for this study, developed and installed on the prototype Korean High Speed Train, and physical characteristics were measured while the KHST runs on the test track. Through this study, remarkable trends of variation are found and analyzed from measured acceleration and vertical contact force between the pan head in pantograph and contact wire in catenary system according to the driving pattern and the train raised a running speed up to 300km/h.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.900-910
• /
• 2000

This study have been performed to investigate the dynamic behavior of the Korean High Speed Train(KHST) during the conceptual design process. This study gets a focus on the analysis of the rigid model, for which the yaw damper layout is modified in a nonlinear limit cycle analysis. In this study, influences of the system parameters such as stiffness of suspension and connection elements as well as damping coefficients were studied and an optimized parameter set is achieved. Throughout the dynamic calculation of KHST on the straight and the curved track, vibration accelerations in car body, ride comforts and wheel rail forces are investigated. Finally the vibration characteristics from rigid car body are compared with those due to the influence of elastic car body.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.154-159
• /
• 2003

In this paper, the design improvement for high speed train carbody, which made by aluminium alloy, was described. The design improvements was achieved in fields of economical efficiency, extrusion, welding, assembling, etc. This paper also describes the result of carbody test. The purpose of the test is to evaluate an safety under the load and operation condition. This strength test based on KTX and reference code is UIC 566 and JIS E 7105. The test results shows that aluminium carbody structural have enough strength for all part.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.170-176
• /
• 2003

The pantograph for Korean High Speed Train was developed and had been evaluating by through "G7- R＆D for home grown high speed train technology". In this study, a relation in mechanical aspect between the train running speed and the current collecting performance of the pantograph is conducted.'for this study, a measuring system for current collecting performance and mechanical characteristics is developed and installed on the prototype Korean High Speed Train, and measurement is conducted while the train runs on the test track. The measuring system is composed of video monitoring system and telemetry & data processing unit. It monitors whether the hazard behavior in the pantograph is occurs or not, and measures acceleration and vertical contact force between the pan head and catenary. Through this study, evaluation of a mechanical vibration characteristics and trend of the pantograph and a interface performance of pantograph - catenary up to 200㎞/h train speed are facilitated.

• Proceedings of the KSR Conference
• /
• 1999.05a
• /
• pp.95-102
• /
• 1999

Because a driver is located in the front end of KHST, he is most likely to be insured at collision accidents. So, it is very important to design some survival space for the driver. To evaluate the driver's safety of KHST (Korean High Speed Train), the front structure of power car is analysed using PAMCRASH under the SNCF accident scenario(collision against a movable rigid mass 15 ton at 110㎞/h). Because the driver's cab of KHST is a modified version of TGV-K, which is not so strong as to protect him, it turns out to be inadequate to guarantee his survival space. Therefore it is recommended to redesign the driver's cab in a crashworthy point of view like the case of TGV-Duplex or NEC.