• Journal of the Korean GEO-environmental Society
• /
• v.15 no.5
• /
• pp.67-74
• /
• 2014

In this study, a constant rate of strain test (CRS) and oedometer test was performed in order to study the consolidation characteristics to the liquid limit using a re-shaped clay which was preconsolidated at a constant pressure. Consolidation samples were made of kaolinite which was mixed with bentonite of 6 %, 9 %, 12 % and 15 % of it by weight and the test value of liquid limit of samples were appeared in 77 %, 84 %, 88 % and 91 % respectively. And then consolidation samples which were agitated sufficiently adding distilled water 2 times of liquid limit were preconsolidated in the condition of a constant pressure of 0.2 MPa. The oedometer test which is commonly used recently and the consolidation test of constant rate of strain which were applied in 0.001 %/min, 0.004 %/min, 0.01 %/min rate of strain according to ASTM, D4186-82 were performed and the preconsolidation pressures were compared and analyzed at 0.2 MPa preconsolidated pressure. As a result, in the case of low value of liquid limit, preconsolidation pressure was appeared same as 0.2 MPa preconsolidated pressure at the high speed strain rate, and in the case of high value of liquid limit, preconsolidation pressure was appeared same as 0.2 MPa preconsolidated pressure at the low speed strain rate.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.213-216
• /
• 2009

In order to see the flame behavior in the gas turbine combustor, combustion test was performed by using sector combustor. Ignition test with torch ignition system was carried out at the various combustor inlet velocity and air fuel ratio. Also, flame blow out limit was measured by changing fuel flow rate with fixed air mass flow rate. In the test results, stable ignition is possible at air excess ratio of 6 and this limit is gradually increased with combustor inlet air velocity. The minimum blow out limit is about 4 at 40 m/s of combustor inlet velocity. This blow out limit is also increased up to about 10 with increasing combustor inlet velocity.

• Explosives and Blasting
• /
• v.20 no.2
• /
• pp.33-41
• /
• 2002

화약류를 사용하여 암반을 절취하는 작업현장에서의 발파공해는 항상 발생하고 있다. 특히 폭약의 폭발로 인해 발생하는 지반진동은 크고 작은 문제를 야기하고 있다. 일반적으로 발파현장에서 사용하고 있는 일반발파와 진동제어(미진동)발파에 대한 의미와 구분 및 시공에 대해 인식시키고자 그동안의 경험과 이론을 토대로 하여 연구하게 되었다. 본 연구에서는 일반발파와 진동제어발파를 구분하는 요소로 암분류 및 진동속도를 지발당장약량과 관계, 암분류에 따른 비장약량 및 발파공당 암절취량 그리고 천공경을 선정하여 고찰하였다. 이들 요소를 기준으로 일반발파와 진동제어발파의 경계가 되는 보안물건으로부터 거리 산출방법에 대해서 연구하였다. 일반발파나 진동제어발파 모두 보안물건에는 한계 진동속도 이내의 진동이 전달되어야 하며, 그 경계가 되는 발파공당 절취암량은 연암의 경우 약$16.67m^3$, 보통암의 경우 약$12.5m^3$, 경암의 경우 약 $10m^3$을 기준으로 하는 것이 바람직하고, 그 경계가 되는 보안물건으로부터 거리는 일정하게 정해진 것이 아니므로 현장에서 대상암반에 대해 시험발파를 실시하여 암분류, 비장약량, 지발당장약량, 한계 진동속도를 기준으로 결정하는 것이 바람직하다. 진동제어(미진동)발파구간내에서 발파설계단가는 일률적이 아닌 약2~3구간으로 분할하여 산출해야한다.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.3
• /
• pp.17-24
• /
• 2004

We present a P-type iterative learning control(ILC) scheme for uncertain robotic systems that perform the same tasks repetitively. The proposed ILC scheme comprises a linear feedback controller consisting of position error, and a feedforward and feedback teaming controller updated by current velocity error. As the learning iteration proceeds, the joint position and velocity mrs converge uniformly to zero. By adopting the learning gain dependent on the iteration number, we present joint position and velocity error bounds which converge at the arbitrarily tuned rate, and the joint position and velocity errors converge to zero in the iteration domain within the adopted error bounds. In contrast to other existing P-type ILC schemes, the proposed ILC scheme enables analysis and tuning of the convergence rate in the iteration domain by designing properly the learning gain.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2007.05a
• /
• pp.1502-1505
• /
• 2007

인터넷 및 네트워크 환경의 비약적인 발전으로 기업체의 모든 기반 Application은 사용의 편리함과 시스템 및 데이터관리의 용이성 때문에 웹 기반모델로 변경되어 사용되고 있다. 그러나, 산업현장설비를 실시간 원격제어 감시하는 시스템인 SCADA(Supervisory Control and Data Acquisition)는 웹의 여러 한계성 때문에 아직까지 기존 Client-Server 모델로 대부분 활용되고 있다. 본 논문에서는 이러한 웹의 한계성 중 Client 시스템의 실시간 통신 방식 및 속도, 부하 등을 기존 Client-Server 방식과 동일한 성능을 갖도록 설계 구현하여 적용하고 성능을 평가 하였다.

• Proceedings of the Optical Society of Korea Conference
• /
• 2001.02a
• /
• pp.74-75
• /
• 2001

현재의 통신망에서는 clock recovery, regeneration 등을 전기적으로 처리하고 있으나 처리속도의 한계가 있고, 미래의 초고속 네트웍은 이러한 전기적 신호처리의 속도한계를 극복하는 기술이 필요하다. 그러므로, 고속의 광교환과 광신호처리 등 광신호를 전기적으로 바꾸거나 제어하지 않고 전광으로 처리하는 기술에 대한 연구가 진행되고 있으며 이러한 전광신호 처리에 고속의 전광 논리소자가 요구된다. 초기의 전광 논리소자 연구에서는 AND, OR, NOR, XOR 등의 기본 논리 기능이 주로 구현되었으며 이를 활용하여 Shift Register, Binary counter, 전광 반가산기, 직/병렬 데이터 변환기와 같은 복합기능 논리소자의 구현 연구가 이루어지고 있다. (중략)

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.11
• /
• pp.971-977
• /
• 2015

A numerical analysis for the performance of compound gyroplane in forward flight was performed. TSM(Transient Simulation Method) was used to analyze the performance of autorotating rotor. CFD was conducted for the fuselages to recognize the variation of aerodynamic performance according to flight speed. At given conditions; airspeed, shaft angle and collective pitch, the quasi-static states of autorotation were determined and the variation of rotor performance was observed. Performance analysis results showed that the effect of aerodynamic characteristics in accordance with the shape of fuselage is so important that the streamlined fuselage is essential to fly fast. Forward flight speed limit is dependent on the autorotation performance of rotor.

• Defense and Technology
• /
• no.7 s.125
• /
• pp.66-71
• /
• 1989

헬기는 수용할수 없는 추가적인 비용의 소모와 공중역학상 적용하기 어려운 중량의 증가없이는 속도와 기동성 및 무장수준의 한계에 도달하였다. 헬기가 비록 지표면 비행기술로 200mph의 속도로 비행할수 있다해도, 10배 또는 그 이상의 속도로 비행하는 열추적 다탄두 전술미사일의 표적이 되는 것이 어느 시점인가를 물어야될 것이다

• Clean Technology
• /
• v.15 no.4
• /
• pp.280-286
• /
• 2009

To evaluate the feasibility of electrodialysis for nitrate-nitrogen removal from wastewater, the effect of operating parameters on the removal of nitrate-nitrogen was experimentally estimated. The limiting current density (LCD) linearly increased with the nitrate concentration and the flow rate. The time when the nitrate concentration of diluate reached at 20 mg/L was linearly proportional to concentration of diluate, and the concentration of concentrate did not affect the removal rate. Increase in the flow rate gave a positive effect on the removal rate and became insignificant at How rates greater than 1.6 L/min. The removal rate increased with the applied voltage, but the increment in the removal rate decreased as the applied voltage approached the LCD. From the operation of the electrodialysis module used in this research, the flow rate of 1.6 L/min and the voltage corresponding to the 80~90% of LCD were found be the optimum operating condition for the nitrate removal from highly concentrated nitrate-nitrogen solutions.

• Korean Journal of Plant Taxonomy
• /
• v.40 no.4
• /
• pp.226-233
• /
• 2010

An intensive study of the embryology of Gymnospermium microrrhynchum was conducted to provide information regarding a discussion of the phylogenetic relationships of the genus, which is yet unstudied. Our results indicated that Gymnospermium is similar to other genera of Berberidaceae in terms of its embryological features. Nevertheless, newly reported and unique features are the well-developed endothelium and the undifferentiated seed coat type. Until the study of Gymnospermium, it may have been considered to be closer to Caulophyllum and Leontice in the tribe Leonticeae. These three genera share many morphological features as well as molecular similarities, by which they are kept in the same tribe, Leonticeae. However, very little detailed embryological data regarding these genera have been published thus far. Gymnospermium was characterized according to the basic type of anther wall formation as well as its glandular tapetum, successive cytokinesis in the microspore mother cell, two-celled mature pollen grains, anatropous and crassinucellate ovules with a nucellar cap, well-developed endothelium, its Polygonum type of embryo sac formation, its nuclear type of endosperm formation, and its undifferentiated seed coat type. In comparison with Nandina, there are many differences, such as the dehiscence of the anther, the cytokinesis in the microspore mother cells, the shape of the megaspore dyad, and the seed characteristics. Although we had no available detailed embryological information regarding Caulophyllum and Leontice, which are genera that are more closely related to Gymnospermium, we could deduce from the phylogenetic relationship that Gymnospermium, Caulophyllum, and Leontice are more closely related to each other than other genera of Berberidaceae on the basis of the seed characteristics.