• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.4
• /
• pp.1-10
• /
• 2022

In this study, to evaluate the possibility of using a steel spring as a displacement-dependent damping device, tensile loading and cyclic loading tests were performed. The main experimental variables were the type of steel (SAE9254 and SS275), the spring constant (700 N/mm, 1,000 N/mm, and 1,400 N/mm), and the presence or absence of heat treatment for SAE9254. As a result of the tensile test, the ratios of the measured spring constant to the design spring constant of the steel springs made with SAE9254 ranged from 1.08 to 1.13, while the ratios of the design spring constant and the measured spring constant of the steel springs made with SS275 ranged from 0.86 to 0.97. After yielding, the slope values of the load-displacement curve of the SAE9254 with/without heat treatment were about 240~251 N/mm and 92 N/mm, respectively, but the slope values of the load-displacement response of SS275 were almost zero. According to the uniaxial cyclic loading test results, all specimens were satisfied with three conditions for a displacement-dependent damping device in KDS 41 17 00 (2019): the maximum force and minimum force at zero displacement, the maximum force and minimum force at the maximum displacement, and the energy dissipation capacity. In addition, the equivalent damping ratios of steel springs made with SAE9254(non-heat treatment) and SS275 were approximately 2.8 times and 1.9 times greater, respectively, than that of steel springs made with SAE9254.

• Journal of Korean Society of Steel Construction
• /
• v.15 no.3
• /
• pp.313-320
• /
• 2003

The governing equation of the post-buckling of shear-deformable uniform columns under a combined load consisting of a uniformly distributed axial load and a concentrated load at a free end was derived and the post-buckling analysis was investigated by using differential transformation. The loads were obtained for various end-slopes. The results obtained by the present method agree well with published results. In this paper, the differential transformation method was illustrated through its application to the non-linear differential equation of the post-buckling. It is expected that applications of the method to more challenging problems will are expected follow in future to ensue.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.8
• /
• pp.789-798
• /
• 2013

The procedures and relevant programs developed for analyzing mechanical load data of wind turbine generator systems, which are obtained through type certification tests, are verified. The following issues according to IEC 61400-13 are covered in the developed programs: data validation, time series analysis, summary load statistics, generation of fatigue load spectra, and estimation of equivalent loads. A capture matrix for normal power production is generated to determine whether the collected data sets are sufficient to carry out fatigue analysis. Fatigue load spectra are obtained through the rainflow counting method using 50 load ranges; finally, equivalent loads are calculated using different S-N curve slopes, m, according to the relevant materials. Case studies are performed using aero-elastic simulation data of the NREL 5 MW baseline wind turbine with a monopile foundation.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.04a
• /
• pp.13-17
• /
• 2000

해저관로가 노출되어 있을 경우 파도와 조류 등에 의한 외적 하중으로부터 안정적이어야 한다. 트랜치 구간 내의 해저관로에 작용하는 유체 입자의 속도와 가속도는 해저면과 비교하여 볼 때 현저히 감소하므로 감쇄 계수를 사용하여 트랜치 구간 내에 설치되는 해저관로의 안정성을 해석한다. 그러나, 다양한 트랜치 구간의 깊이와 기울기에 대한 감쇄 계수에 대해 많은 자료가 부족하여 실제 설계에는 한정된 계수들이 이용된다. 본 논문에서는 다양한 깊이와 기울기를 가진 트랜치 구간의 실험 모형을 제작하여 회류 수조에서 P.I.V(입자 영상 속도계) 기법을 이용하여 여러 속도에 대하여 실험을 수행하였다. 다양한 트랜치 구간 내의 실린더 주변의 유동 특성과 유체 입자의 수평 속도를 측정하여 항력 감쇄 계수를 산출해 냈으며 실제 해양 공사에서 적용 가능한 안정성 해석 기준을 제시하였다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.15 no.3
• /
• pp.523-534
• /
• 2002

Free vibration and buckling analysis of multi-delaminated composite beam-columns subjected to axial compressive load is performed in the present study In order to investigate the effects of multi-delaminations on the natural frequency and the elastic buckling load of multi-delaminated beam-columns, the general kinematic continuity conditions are derived from the assumption of constant slope and curvature at the multi-dclamination tip. The characteristic equation of multi-delaminated beam-column is obtained by dividing the global multi-delauunated beam-columns into segments and by imposing recurrence relation from the continuity conditions on each sub-beam-column. The natural frequency and the elastic buck)ing load of multi-delaminated beam-columns according to the incremental load of axial compression, which is limited to the maximum elastic buckling load of sound laminated beam-column, are obtained. It is found that the sizes, locations and numbers of multi-delaminations have significant effect on natural frequency and elastic buckling load, especially the latter ones.

• Journal of the Korean GEO-environmental Society
• /
• v.12 no.1
• /
• pp.27-33
• /
• 2011

In general, the shear strength of a clay specimen under the direct shear test and the triaxial compression test increases with an increase in the shear rate. This study investigates the effects of shear rate and silt content on the stress-strain behavior of remolded Gwangyang clay, by changing the shear rate and the silt content. Based on the results of the triaxial compression tests, the equi-strain line of remolded Gwangyang clay shows initially positive slope and then becomes flat at certain strain level. As the strain level where the equistrain becomes flat is different depending on the soil with different silt contents, this can be considered as the inherent property of soil.

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2023.11a
• /
• pp.244-246
• /
• 2023

아파트 신축공사 흙막이 가시설 현장에 근접 매설된 상수관의 누수 및 파열 사고로 인접 건물이 공사현장 방향으로 58~188mm 기울어졌으며, 지중수평경사계 계측결과 21.07.20일 22.64mm가 21.10.18.일 101.46mm로 급격하게 78.82mm의 큰 수평 변위가 발생되었으며, 이로 인해 흙막이 가시설의 사보강재가 변형되고 토류판 일부가 파손되었다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.4
• /
• pp.57-66
• /
• 2002

본 연구는 굽힘 하중하에서 탄성평판 구조 해석을 위한 경계적분방법 구성을 주목적으로 하고 체계적인 모듈화시스템 개발의 첫 이론 부분을 확립하였다. 굽힘 문제에서의 4개의 고유변수인 처짐, 기울기, 굽힘모우멘트, 상당 전단력의 항으로 경계적분방정식을 구성하였다. 물리적인 의미를 갖는 두 새로운 핵함수 도입으로 구성된 이들 적분방정식은 경계요소 구성시 나타나는 특이거동의 문제점을 간단한 두 탄성해에 의해 정규화 시켰으며 수치 적분 과정도 Cauchy 주치 적분 수렴성에서의 특별취급과는 달리 효율적으로 일반화시켰다. 경계적분식의 수치해석방법을 서술하였으며 집중하중하의 비대칭문제의 근사수치해를 도시하였다.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.5 no.2
• /
• pp.125-138
• /
• 2001

고유진동수와 감쇠비는 지진이나 바람과 같은 동적 횡하중에 대해 구조물의 응답을 결정하는 주요한 특성이다. 본 연구는 지진하중에 대하여 목표응답 수준을 만족하는 구조물의 고유진동수와 감쇠비를 지정하고, 이 값을 실현하는 점탄성 감쇠기 파라미터의 처적분포를 구하는 설계방법을 제안한다. 여기서 지정할 고유진동수와 감쇠비는 목표응답 수준을 만족하는 여러 조합 중 설계조건과 원래 건물의 특성에 따라 결정될 수 있다. 제안한 설계방법은 점탄성 감쇠기의 감성 파라미터를 고유값의 기울기 정보를 바탕으로 분포시키므로 최적 위치와 크기에 대한 정보를 동시에 제공한다. 예제로서 평면 10층 전단 건물을 대상으로 최적설계를 수행하여 지정된 고유값을 실현하는 파라미터의 최적분포를 구하고 이를 통해 제안한 최적 설계의 특성을 확인하였다. 또한 더 나아가 3차원 일방향 비대칭 전단전물에 제안된 최적설계를 수행하여 그에 대한 적용가능성을 확인하였다.

• Journal of the Korean Ceramic Society
• /
• v.33 no.3
• /
• pp.339-347
• /
• 1996

Mechanical properties(flexural strength hardness fracture toughness) of alumina ceramics were evaluated. Alumina products of four companies were selected and three of those were made in Korea and one of those was made in Japan. The large differences according to manufacturing companies had resulted from flexural strength and weibull modulus which had a wide ranges of 300 to 400 MPa and 5 to 15 respectively. Critical indenstation load which could be neglected the effect of elastic recovery was about 9.8N and Vickers' hardness were about 15 GPa. Fracture toughnesses were evaluated by IF and ISB method. It was more preferable to the average at one indentation load that fracture toughness were obtained from the slope of the relationship between indentation load and crack length in IF method and between indentation load and fracture load in ISB method and fracture toughness was about 4 MPa·m1/2.