• Korean Chemical Engineering Research
• /
• v.58 no.4
• /
• pp.665-674
• /
• 2020

Low-frequency pressure fluctuations in an external-loop airlift reactor were investigated. Low-frequency pressure fluctuations could be measured by shooting videos about liquid levels in the four piezometric tubes which were installed at the lower and upper parts of the riser and downcomer using a cellular phone. The periodic characteristics of pressure fluctuations were proved by the calculation of their auto-correlation function and cross-correlation function. Even if the riser superficial gas velocity was constant, the riser and downcomer gas holdups as well as wall pressures were periodically changed due to the inertia of circulating liquid. In general, the intensity of pressure fluctuations increased with an increase in the gas velocity. When the unaerated liquid height was 0.04 m, the maximum period of pressure fluctuations was found at the specific gas velocity (0.14 ms^-1). It was because the maximum inertia of circulating liquid resulted from a reduction in the increasing rate of the liquid circulation velocity and a decrease in the volume of the effectively circulating liquid with an increase in the gas velocity.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2016.11a
• /
• pp.201.1-201.1
• /
• 2016

전주된 Invar (Fe-35%Ni) 박판 위에 증착된 Cu 박막은 스퍼터 전력량이 증가할수록 증착속도가 증가하였다. Cu/Invar 박판이 Invar 박판보다 면저항 값이 34%로 작았다. Invar 박판 위에 Cu가 증착되면 최대자화와 투자율은 각각 40.3, 65.0 [%] 감소하였다. Cu 박막의 탄성하강강성도, 마찰계수, 피로한계는 각각 45, 0.130, 0.093 이었다. 동적 나노 압침법으로 얻은 Invaar/Cu 박막의 하중-시간-변위 곡선의 가장 큰 차이는 탄성하강강성도(elastic stiffness) 이었다. 미세경도와 나노경도의 실험적 관계식은 $Y[GPa]=9.18{\times}10^{-3}X[Hv]$ 이었다. 나노압침선단의 하중분포를 이차원 선형 및 비선형 유한요소해석을 통하여 1.0 [mN] 의 정적하중을 가한 Cu 박막은 486 [mN] 으로 예측되었다. 이는 표면탐침현미경으로 관찰한 압흔의 변형정도와 유사한 경향을 보였다.

• The KIPS Transactions:PartB
• /
• v.8B no.4
• /
• pp.327-334
• /
• 2001

본 논문에서는 기울기하강과 동적터널링이 조합된 학습알고리즘의 다층신경망을 이용한 고신회성의 회귀분석 모델을 제안하였다. 기울기하강은 빠른 수렴속도의 최적화가 가능하도록 하기 위함이고, 동적터널링은 국소최적해를 만났을 때 이를 벗어난 새로운 연결가중치를 설정하여 전역최적해로 수렴되도록 하기 위함이다. 또한 대용량의 입력 데이터를 통계적으로 독립인 특징들의 집합으로 변환시키는 주요성분분석 기법의 속성을 살려 학습데이터의 차원을 감소시킴으로서 고차원의 학습데이터에 따른 회귀분석 모델의 제약도 동시에 해결하였다. 제안된 기법의 신경망을 3개의 독립변수 패턴을 가진 암모니아 제조공정문제와 10개의 독립변수 패턴을 가진 자동차 연비문제에 각각 적용하여 시뮬레이션한 결과, 기존의 역전과 알고리즘의 신경망이나 주요성분분석에 의한 차원을 감소시키지 않은 학습패턴을 이용한 신경망보다 각각 더욱 우수한 학습성능과 회귀성능이 있음을 확인할 수 있었다. 또한 학습패턴의 영평균 정규화로 회귀용 신경망의 성능을 더욱 더 개선하였다.

• Journal of Korea Foresty Energy
• /
• v.22 no.1
• /
• pp.24-29
• /
• 2003

Using woodceramics made from sawdust board of Larix leptolepis thinning logs, change in surface temperature were investigated, by the rate of resin impregnation and burning temperature. As the surface temperature of silicon rubber heater was going up, that of woodceramics also increase rapidly. Woodceramics made from under the condition of the rate of resin impregnation 70-80% and burning temperature 800-$1000^{\circ}C$, were higher than that of surface temperature. Also, it was found that woodceramics maintained heat for a long time because the descending velocity of their surface temperature was lower than that of the heater.

• Proceedings of the KIEE Conference
• /
• 1999.07g
• /
• pp.2833-2835
• /
• 1999

이 논문에서는 임의의 시스템 동정에 사용되는 적응필터의 계수를 최적화시키는 방법으로 광범위하게 사용되어지고 있는 기존의 적응 알고리즘인 Least Mean Square(LMS)방법과 최근들어 다양한 최적화 문제에 응용되고 있는 유전자 알고리즘(GA)을 합성한 하이브리드 형태의 적응 알고리즘을 사용한다. 이 알고리즘은 TIR 필터를 설계하는데 있어, 경사하강법의 개념을 사용함으로써 야기되는 지역 수렴문제의 단점을 보완하기 위해, 미분과 같은 결정론적인 규칙없이 단지 확률적인 연산자만으로 진행하는 유전자 알고리즘을 이용한다. 그리고 유전자 알고리즘에 있어서 확률적인 연산을 사용함으로써 발생하는 많은 계산량과 느린 수렴속도 문제를 LMS의 경사하강법을 이용하여 보완한다. 이처럼 유전자 알고리즘이 지닌 장점과 LMS 알고리즘이 갖는 장점을 이용하여 각 알고리즘이 지니는 단점을 서로 보완함으로써 알고리즘의 성능을 향상시키고 이 향상된 알고리즘을 이용하여 최적 필터계수를 찾는다 이렇게 얻은 필터계수값을 이용하여 적응 필터의 성능을 확인 평가한다.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.22-28
• /
• 2007

Using woodceramics made from sawdust board of pine thinning logs, changes in surface temperature were investigated, by the heating rate and keeping time at maximum temperature. The heating rate of $2^{\circ}C/min$ and keeping time at maximum temperature 1 hour, were the highest in surface temperature. Also, it was found that woodcermics maintained heat for a long time because the descending velocity of their surface temperature was slower than that of the heater.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.6
• /
• pp.41-48
• /
• 2014

In this study, the behavior of fill dam with continuous water level change considering velocity changes via centrifugal model test was investigated. In addition, the collapse of fill dam due to the overflow was also experimentally simulated. The experimental results demonstrate that the pore water pressures and displacements vary in proportion to the water-level-change velocity, and the displacement increment is independent to the water-level-change velocity. Also, it is confirmed that the continuous water level change induces to the progress of fill-dam deformation due to displacement accumulation and the fill-dam stability dramatically degrades owing to the overflow. Hence, the real-time monitoring of pore water pressures and displacements of fill dam, and the control of water level in heavy rain through the countermeasure such as opening sluice gates are needed to ensure the stability of fill dam.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.2
• /
• pp.1-6
• /
• 2011

This paper describes a phase modulation I/O (PMIO) serial interface circuit that supports 1Gbps transfer rate with 12mW power consumption at 1.2V supply. The proposed PMIO which consists of TX and RX blocks utilizes a phase modulation technique. The rising edge is fixed to get the clock phase information and falling edge has multi positions for the multi-data information to increase the transfer rate. The designed circuit use the 16 possible falling edge positions. The data transfer rate is four times faster than the clock rate. The circuit has been implemented using $0.13{\mu}m$ CMOS process. Measured results show the circuit exhibits peak-to-peak jitters of transfer data (phase data) and recovery data.

• Journal of the Korean Data and Information Science Society
• /
• v.20 no.3
• /
• pp.527-539
• /
• 2009

The purpose of this study was to evaluate the influence of ankle joint mobilization on equilibrium ability of supinated foot. Both Joint mobilization group(n=20) and control group(n=20) were measured an equilibrium ability by Balance performance monitor at pre-test, post-test in 2 weeks, post-test in 4 weeks and follow-up test in 2 weeks. The sway area, sway path length and sway maximum velocity of the joint mobilization group were significantly reduced among the experimental period (p<.05). The reduction of sway area, sway path length and sway maximum velocity were significantly different between the joint mobilization group and the control group at in 2 weeks, 4 weeks and follow-up test(p<.05). In conclusion, we were found that ankle joint mobilization could reduce sway area, sway path length and sway max velocity and improve a balance for the individuals with supinated foot.

• Applied Chemistry for Engineering
• /
• v.8 no.5
• /
• pp.816-821
• /
• 1997

The hydrodynamics and the liquid flow characteristics were investigated in an internal circulation airlift reactor with a single nozzle as a gas distributor. In an air-water system, the gas holdup in the individual flow zone and the impulse-response curve of tracer were measured at various gas velocities and reactor heights. Experimental results showed that for the higher gas velocity(>about 8 cm/s), the flow behavior of bubbles in the riser was turbulent flow due to strong bubble coalescences and the axial height of dispersion zone of large bubbles having uniform sizes in the downcomer was decreased with increasing gas velocity. And mean gas holdups in the individual flow zone and the reactor were increased with increasing gas velocities and were decreased with increasing heights of the top section of the reactor and it was decreased with increasing the height of the top section and gas velocity. Flow characteristics of liquid in the riser and the downcomer was tend to access to plug flow and the overall flow behavior of liquid was mainly varied with the size of the top section which it was assumed to be perfect mixing zone. In these conditions, liquid circulation velocities were increased with increasing gas velocities and they were higher than those by using other gas distributors.