• Journal of the Korean Society of Safety
• /
• v.15 no.1
• /
• pp.140-145
• /
• 2000

This paper was composed with fatigue test of the cruciform specimens, as load carrying and non-load carrying type. It also has performed computational analyses for geometric condition of the fillet welding bead. As test results, the effect of stress ratio in the specimen was insignificant. Stress ranges were varied with R=0.1~0.2. The fatigue cracks that were found in the load carrying type specimens and most specimens welded with contact were developed at the end of welds. The fatigue strength of specimen that have fractured in maternal plate was found about ${\Delta}\sigma_c$=63.5MPa. It's about 24% less than that of the non-load carrying type specimens having about ${\Delta}\sigma_c$=83.8MPa. A category of the Fatigue design specifications which provide for cruciform details was defined grade C as a stress of the maternal member. And then, the fatigue strength to be transformed into the maternal stress was found about 78.27 MPa, it tends to be less than that of allowable fatigue strength.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.4
• /
• pp.467-474
• /
• 2010

Stainless steel sheets are widely used as the structural material for railroad cars and commercial vehicles. Structures made of stainless steel sheets are commonly fabricated by gas welding, For the fatigue design of gas welded joints such as fillet joints, it is necessary to obtain design information of the stress distribution at the weldment as well as the fatigue strength of the gas-welded joints. Further, the influence of the geometrical parameters of gas-welded joints on stress distribution and fatigue strength must be evaluated. in this study, ${\Delta}P-N_f$ curves were obtained by fatigue tests. and, the ${\Delta}P-N_f$ curves were rearranged on the basis of the ${\Delta}{\sigma}-N_f$ relation for the hot-spot stresses at the gas-welded joints. These results, were used for conducting an accelerated life test(ALT) From the experiment results, an acceleration model was derived and factors were estimated. The objective is to obtain the information required for the analysis of the fatigue lifetime of fillet welded joints and for data analysis by the statistic reliability method to save time and cost and to develop optimum accelerated life prediction plans.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.303-303
• /
• 2013

표면에 부착된 나노/마이크로 입자는 다양한 분야에서 오염물질로 작용한다. 특히 형상이 미세하고 공정 단계가 복잡한 반도체 및 디스플레이 등의 전자 소자 공정에서 미치는 영향이 크다. 따라서 입자상 오염물질의 제거에 관하여 상용화된 습식 세정 방법이 다양하게 존재하지만 표면 손상, 화학 반응, 부산물, 세정 효율 등 여러 가지 문제점이 있어 새로운 세정 방법이 요구된다. 이에 건식 세정 방법, 그 중에서도 입자의 충돌을 통해 제거하는 방법인 에어로졸 세정, 필렛 세정 등이 개발되었으나 마이크로 크기로 생성되는 입자로 인하여 형상의 손상이 크다. 따라서 본 연구에서는 나노 단위로 기체/고체 혼합물만 생성하여 세정하는 가스 클러스터 세정 방법을 이용하여 이러한 문제점을 해결하고자 하였다. 클러스터 세정 장비를 이용한 표면 처리는 충돌에 의한 제거에 기반한다. 따라서 생성 및 가속되는 클러스터로부터 대상으로 전달되는 운동량의 정도가 세정 특성에 영향을 미치며 이는 생성되는 클러스터의 크기에 종속적이다. 생성 클러스터의 크기 분포는 분사 거리, 유량, 분사 각도, 노즐 냉각 온도 등의 변수에 관한 함수이다. 따라서 본 연구에서는 $CO_2$ 클러스터를 이용한 세정 특성을 정의 및 제어하기 위하여 생성되는 클러스터 특성에 관하여 이론적, 수치 해석적, 실험적 연구를 수행하였다. 먼저, $CO_2$의 물리적 특성 및 이를 이용한 특정 크기 오염 물질을 제거하는데 요구되는 임계 클러스터 크기 계산을 이론적으로 구하였다. 이는 오염물질의 부착력과 클러스터의 운동량 전달에 의한 제거력의 비교를 통해 이루어졌다. 두 번째로 클러스터 크기분포를 수치 해석적으로 예측하기 위하여 각 조건에 대하여 유동해석을 수행하고 이를 통해 구해진 노즐 내 기체의 냉각 속도를 GDE (General Dynamic Equation) 계산에 대입하여 구하였다. 마지막으로 PBMS(Particle Beam Mass Spectrometer)를 이용하여 실험적으로 클러스터 크기분포를 각 조건에 대하여 구할 수 있었다. 또한 크기 분포 경향에 대한 간접적 확인을 위하여 포토레지스트가 코팅된 웨이퍼에 클러스터의 충격으로 생성된 크레이터 크기의 경향을 분석하였다. 이와 같은 방법에 의하여 생성되는 클러스터는 노즐의 유량 증가, 온도 상승에 각각 비례하여 작아지는 것을 확인할 수 있었다.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• v.9 no.2
• /
• pp.195-199
• /
• 2005

Semi automatic welding method to use carriage for welding at large size block manufacture welding process of present shipbuilding industry is used much. Carriage is device that transfer welding torch in horizontal fillet weld here, but because it is no function that chase welding like robot welding method, use can be impossible in curved line welding, and simply use in straight line welding. Also, because it is no function that chase welding, though welding mistake corrects this happening often in straight line welding, much times and expense are cost. Added welding chase sensor and 80C196KC microcontroller that use strain gauge to carriage that is using present in paper that see hereupon and manufacture a private line model and container box model welding because developing system that can chase welding automatically straight line and curved line welding establishing and investigate about chase phenomenon.

• Journal of Welding and Joining
• /
• v.23 no.5
• /
• pp.37-42
• /
• 2005

The non-destructive Inspection of the fillet weldment has difficulties due to its geometrical complexity and uneasy access. The surface shear horizontal wave (SH-wave), however, has been successfully applied to the detection of cracks on the surface and sub-surface of the filet weldment heel part. The conventional ultrasonic inspection using the surface SH-wave is usually a contact method using piezoelectric transducer. Thus, it is not suitable for a field application because the reliability and repeatability of inspection are significantly affected by test conditions such as couplant, contact pressure and pre-process. In order to overcome this problem, a non-contact SH-wave inspection method using EMAT is propose. The experimental results with this non-contact method are compared with those with a conventional ultrasonic method in fillet weldment with slit type defects. It is shown that the non-contact inspection technique requires simple procedure and less time in the fillet weldment inspection.

• Journal of Food Hygiene and Safety
• /
• v.35 no.6
• /
• pp.561-566
• /
• 2020

Nowadays, with increase of seafood consumption, there have been increasing reports of defective seafood products. There have been incidents of red drum (Sciaenops ocellatus) being sold as red seabream (Pagrus major). In this study, we sought to develop and validate species-specific PCRs to differentiate between P. major and S. ocellatus to prevent the sale of S. ocellatus as P. major. Primers for P. major were designed to bind 12s rRNA and those for S. ocellatus were designed to bind 16s rRNA. Multiplex PCR showed a 468 bp amplicon for P. major and a 181 bp amplicon for S. ocellatus. The limit of detection of P. major and S. ocellatus was present at 1 ng each. The developed primers were validated with 19 P. major samples of food items purchased through the internet. Using this monitoring method, the experimental results and tested species were in agreement. Hence, the developed multiplex PCR method is considered reliable to authenticate P. major and S. ocellatus.

• Asia-pacific Journal of Multimedia Services Convergent with Art, Humanities, and Sociology
• /
• v.5 no.2
• /
• pp.207-214
• /
• 2015

Stress concentrations around discontinuities, such as a hole or a sudden change in cross section of a structural member, have great important cause in the most materials failure because the stress near the points of application of concentrated loads can reach values much larger than the average value of the stress in the member. This paper presents the stress concentrations between fillet and hole at different locations in a stepped plate under tensile loading. The analysis for interaction effect of stress concentration was performed by photoelasticity and ANSYS which is a commercial finite element software. From the analysis results, the circular hole located at the different position from the fillet radius can cause different values of stress concentration factor within interacting region.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.56 no.6
• /
• pp.818-825
• /
• 2023

The surge in online seafood consumption has increased parcel delivery, leading to a need to implement effective preservation methods. As the cold chain system is not fully established in Korea, styrofoam boxes and cold packs are commonly used for low-temperature seafood distribution. The impact of cold packs on product preservation depends on the number utilized. Herein, the freshness of vacuum-packed frozen fish fillets (Paralichthys olivaceus and Scomber japonicus) stored at 25±0.5℃ for up to 84 h was measured. Chemical (pH and volatile base nitrogen), microbiological (viable cell count), and physical (odor intensity) properties were assessed using 2 or 4 cold packs in a styrofoam box. Four cold packs yielded lower values, indicating superior freshness, and extended fish freshness by approximately 12 h compared with two cold packs. Therefore, it is recommended to use a minimum of 4 cold packs (-350 g/cold pack) in a styrofoam box for distributing approximately 300 g of frozen fish fillets at room temperature during the summer, considering an average delivery period of 2 days in Korea.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.10
• /
• pp.1337-1345
• /
• 2011

In pressurized water reactors (PWRs), the reactor pressure vessel (RPV) upper head contains numerous control rod drive mechanism (CRDM) nozzles. In the last 10 years, the incidences of cracking in alloy 600 CRDM nozzles and their associated welds has increased significantly. Several axial and circumferential cracks have been found in CRDM nozzles in European PWRs and U.S. nuclear power plants. These cracks are caused by primary water stress corrosion cracking (PWSCC) and have been shown to be driven by welding residual stresses and operational stresses in the weld region. Therefore, detailed finite-element (FE) simulations for the Korea Nuclear Reactor Pressure Vessel have been conducted in order to predict the magnitudes of the weld residual stresses in the tube materials. In particular, the weld residual stress results are compared in terms for nozzle location, geometry factor$r_o$/t, geometry of fillet, and adjacent nozzle.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.32 no.6
• /
• pp.251-261
• /
• 2022

This paper describes the finite element analysis and die design change of spring retainer forging process to reduce the cold forging load and plastic forming stress concentration. Plastic deformation analysis was carried out in order to understand the forming process of workpieces and elastic stress analysis of the die set was performed in order to get basic data for the die fatigue life estimation. Cold forging die design was set up to each process with different four types analysis progressing, the upper and lower dies shapes with combination of fillets and chamfers shapes of cold forging dies. This study suggested optimal cold forging die geometry to reduce cold forging load. The design parameters of fillets and chamfers are selected geometry were selected to apply optimization with the DoE (design of experiment) and Taguchi method. DoE and Taguchi method was performed to optimize the workpiece preform shape for spring retainer forging process, it was possible to expect an increase in cold forging die life due to the 20 percentage forging load reduction.